BMW Drag Racing Standings

[Captain]

I have track coilovers, no launch, no boostcontrol, pumpgas.
So mine is not setup for dragrace either..

So i´m very satisfied!

Then like i said, GOD!

[Haavard ///M3]

vsmotor.no/filmer.html

BMW M3 vs motor
1422hp 1610nm
1/4 mil 7,70sec 286km/h
New world record!!!



Info: gatebil.no/forum/viewtopic.php?t=1407

[MrBlonde]

vsmotor.no/filmer.html

BMW M3 vs motor
1422hp 1610nm
1/4 mil 7,70sec 286km/h
New world record!!!



Info: gatebil.no/forum/viewtopic.php?t=1407

Awesome achievement, but this thread is for street cars.

[MrBlonde]

Andreas is still on the top of the heap!

[mike radowski]

It's hard to take the man out! I'm just a poor kid trying to cobble together a street car for some friendly competition. Just because there is silence on the board doesn't meen there's silence at the shop

[///M3 CRAZY]

i see i have to try to break into the 11's to get on this list. i am getting close. chipping away at it.

[Alphaman]

i see i have to try to break into the 11's to get on this list. i am getting close. chipping away at it.

You can dooo it!

[MrBlonde]

i see i have to try to break into the 11's to get on this list. i am getting close. chipping away at it.

Nearly there dude! You can make it!

[MrBlonde]

Go Donovan!

[BMWSOB]

Moovin on up!! Need more track time now!!!

[///M3 CRAZY]

i pulled the seats out and headed for the track tomorrow night! lets see if 100lbs less will get me into the beloved 11's.

[BMWSOB]

You Can Doo Eeeeeeet!

[card counter]

Getting near to that time of year.
Study the list and pick a goal and get-r done

[and1c]

Getting near to that time of year.
Study the list and pick a goal and get-r done

Cant wait to see your monster at the strip ulysees

[mike radowski]

The silver bullet is coming together nicely. I would like to shave a few seconds off of my previous best this season.

[highboostingm3]

I would like to shave a few seconds off of my previous best this season.

[card counter]

Cant wait to see your monster at the strip ulysees

Should be interresting.Im just hoping to keep the trans in one piece.

Will start out at low 22 psi and work from there.

[and1c]

Should be interresting.Im just hoping to keep the trans in one piece.

Will start out at low 22 psi and work from there.

What is the high setting mate??
35psi?? ~

[card counter]

What is the high setting mate??
35psi?? ~

Yes but I never run the maximum psi on street or track just when on dyno.
Probally the most it will see is 30-32

[MrBlonde]

George how about some clarification? What size Mickey Thompsons did you run under the blue car? Looks like they are right out to the edge of the widebody which makes it a widebody car and not a street car.

[m3jasper]

George how about some clarification? What size Mickey Thompsons did you run under the blue car? Looks like they are right out to the edge of the widebody which makes it a widebody car and not a street car.

The alignment is what gives you that impression. The widebody panels are molded onto the stock quarters. I'll try to take a better picture next time around. The tires are 255/50/16 Mickey Thompson ET Street Radials...

[marc1119]

The alignment is what gives you that impression. The widebody panels are molded onto the stock quarters. I'll try to take a better picture next time around. The tires are 255/50/16 Mickey Thompson ET Street Radials...

Thank you for the answer, Dave..Official ICS spokesperson and official ICS cameraman...

You are doing a great job..

[m3jasper]

Thank you for the answer, Dave..Official ICS spokesperson and official ICS cameraman...

You are doing a great job..

[GG///M3]

What can you do when some just hate.

[highboostingm3]

George how about some clarification? What size Mickey Thompsons did you run under the blue car? Looks like they are right out to the edge of the widebody which makes it a widebody car and not a street car.

Those widebody panels aint so wide. I used similar panels at first and without tampering with them I scratched my head thinking, "These only help from maybe 255 - 275. The reason being is that now the quarter pops out from top and comes straight down where the stock comes at an angle and then has a decent flare. They end up pretty close in clearance so truthfully the only difference is aesthetics. Plus with this car you can see the stock rear bumper and stockish side skirts are used without having to modify. I ended up having to have special mounting brackets and a ton of fabricating to widen the quarters I had to fit decent rubber back there on my car.

These look like the same MTs that would fit under stock body work. If you agree, I will be purchasing the same e30 m3 rims and tires for my car when it is ready for the strip.