Dear all, this my first post since joining. I have a 2005 545i with SMG. After one morning of “no start”, the car sat for a while which drained the battery. I have now charged the battery to 100% and it is being maintained with the trickle charger so I can performed diagnostic. Using a Foxwell NT520 I retrieved the list of code below. I am very handy but need help and guidance with understanding and how to proceed by elimination to fix the various codes. Someone please help!
Vehicle: /scan/BMW/
Test Path: BMW, Automatic selection, Auto Scan
Status Report
2E8B DME: Intelligent battery sensor, signal present
2A67 DME: Valvetronic, actuator motor: activation present
2A68 DME: Valvetronic, actuator motor 2: activation present
2A6A DME: Valvetronic, actuator motor 2: power supply present
2DD8 No message, receiver DME, transmitter Active Steering present
51B3 Implausible message, engine oil temperature, receiver EGS, transmitter DME-DDE present
4EF9 SMG: Clutch speed sensor not present
51B1 Implausible message, wheel speeds, rear axle, receiver EGS, transmitter DSC not present
4FB5 SMG: Control unit: internal fault (A/C converter) not present
4FB2 SMG: Control unit: internal fault (watchdog) not present
4E26 SMG: Solenoid valve, clutch not present
4E91 SMG: Hydraulic-pump relay present
4E21 SMG: Solenoid valve, gear selection, fuel injector 2 not present
4F73 SMG: Gearbox: gear deselection unsuccessful not present
CF07 Transmission control unit: Communication fault: PT-CAN not present
5EAF DSC: DSC sensor, internal not present
D35D No message (active steering, 0x1FC) present
E484 SMBF: K-CAN line fault present
E444 SMFA: K-CAN line fault present
E244 SZM: K-CAN line fault present
A468 CID: External open circuit (LVDS data line) present
E5C4 CID: K-CAN line fault present
D944 DWA: K-CAN line fault present
9C54 IHKA: AUC sensor present
E704 IHKA: K-CAN line fault present
9C55 IHKA: Fogging sensor present
A548 Message (Active Steering, 0x1FC) faulty, receiver KOMBI, transmitter AFS present
E104 KOMBI: K-CAN line fault present
E584 KBM: K-CAN Line fault present
930C LM: Clearance light, left (E60, E65), outer (E60 Halogen), faulty present
E504 LM: K-CAN line fault present
DA04 SHD: K-CAN line fault present
To many faults clear them all and start over also just because you charged the battery does not make it good, how old is it and did you load test it
Does it crank at all?
SMG problems can stop the starter from cranking.
-Abel
- E36 328is ~210-220whp: Lots of Mods.
- 2000 Z3: Many Mods.
- 2003 VW Jetta TDI Manual 47-50mpg
- 1999 S52 Estoril M Coupe
- 2014 328d Wagon, self-tuned, 270hp/430ft-lbs
- 2019 M2 Competition, self-tuned, 504whp
- 2016 Mini Cooper S
I bet the battery is toast. That clicking sound is from the starter. I bet the voltage at the starter drops to zilch when you try to start the engine. That starter takes a bunch of power. Electrical power is measured in watts. Watts=voltage x current (measured in amps). If the voltage drops the starter tries to draw more amps to compensate. But the battery can’t provide the required amps. Have the battery tested for cold cranking amps.
Bookmarks