Results 1 to 5 of 5

Thread: NCS EXPERT HELP!! Coapi2020 error

  1. #1
    Join Date
    Aug 2018
    Location
    columbia sc
    Posts
    66
    My Cars
    2002 CSM M3, 1997 m3

    NCS EXPERT HELP!! Coapi2020 error



    What is going on with this error? Using bimmergeeks tools and datens, my cable works with winkfp and inpa.

    My copy of ncs has manipulation mode and factory mode only, so I changed the profile settings of manipulation to meet those of expert mode, at least as much as I could.

    Every time I select e46 to get the cars VO I get a coapi2020 code... any help?


    Sent from my iPhone using Tapatalk

  2. #2
    Join Date
    Apr 2018
    Location
    Turkey
    Posts
    1
    My Cars
    1999 BMW 328
    Honostly I didn’t even read the error parameters (i never do if it is longer than 7 lines!)
    Just the way it looks (from my ignorant point of view) like communication failure which could happen when;
    -you did not turned your key to the position 2
    -obd2 or 20pin connectors have a problem
    -old car with not soldered cable or new car with soldered cable
    (if a switched cable is being used switch is on the wrong side)
    -cable driver is not set to same port selected when installing standart tools (usually COM1)
    -cable driver latency setting is a value different than 1
    Last edited by SkyDeity; 02-26-2019 at 06:44 PM.

  3. #3
    Join Date
    Aug 2018
    Location
    columbia sc
    Posts
    66
    My Cars
    2002 CSM M3, 1997 m3
    I believe it ended up being my cable, my current one works with inpa and everything but ncs. Borrowed one from a friend and it was all good


    Sent from my iPhone using Tapatalk

  4. #4
    Join Date
    Jul 2007
    Location
    Philadelphia, PA
    Posts
    5,660
    My Cars
    2005 M3 & 2004 330i
    Quote Originally Posted by pullinmyhairout View Post
    I believe it ended up being my cable, my current one works with inpa and everything but ncs. Borrowed one from a friend and it was all good


    Sent from my iPhone using Tapatalk
    Solder pins 7 and 8 together on your cable

  5. #5
    Join Date
    Mar 2019
    Location
    uk Canterbury Kent
    Posts
    34
    My Cars
    2004 BMW E46 convertible
    why is it when I go to GM5 C01,C02,C03,C04,C05,C06. I am getting this message
    a RED( X )come up 15:45:29 An error occurred while reading "C:\NCSEXPER\WORK\FSW_PSW.TRC": Unresolved parameter
    keyword "500ms" in function "HUB_VERZOEGERUNG_FH_VORN". Make sure chassis and module match those of the trace file.
    knowing I have had GM5 C01 & C06 working befor but now all of them are not ? so I can get back to codding
    Last edited by TonyLou; 03-13-2019 at 03:10 PM.

Similar Threads

  1. Help with NCS Expert - COAPI - 1000 error
    By redbull325is in forum Diagnostic Software
    Replies: 2
    Last Post: 01-14-2013, 05:58 PM
  2. DIS,NCS Expert = help please
    By lilone in forum Diagnostic Software
    Replies: 10
    Last Post: 08-09-2012, 04:19 PM
  3. NCS Expert - coding faulty error?
    By GFRoSTY in forum Diagnostic Software
    Replies: 1
    Last Post: 06-23-2012, 08:03 PM
  4. NCS expert help!
    By twinturbo888 in forum Diagnostic Software
    Replies: 6
    Last Post: 01-03-2011, 09:02 AM
  5. NCS Expert Help
    By platinum911 in forum Diagnostic Software
    Replies: 1
    Last Post: 09-24-2010, 11:35 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •