x2 Staggered Sets, Style 24(LTW) wheels(non-stamped)

[SneauxM3]

Have my two sets of staggered LTW wheels I have decided to offer up for sale. No bends, no welds, no bs. Just my wheels that I have yet to get refinished to match.

Polished set - x2 7.5" wheels, x2 8.5" wheels - 36112227850 & 36112227860
Grey set(originally polished) - x2 7.5" wheels, x2 8.5" wheels - same part #s

The grey set(originally polished(860))has been powder coated by the PO, prep work seems to be lacing, as it has flaked off almost completely around the lips of the wheel, and you can see in the photos where other pieces have flaked off.

The polished set has some rash on two wheels, with a close up of the worst spot. Which I believe was made by a terrible tire-tech mounting tires.

Tires are NOT considered in pricing, as they're junk anyways.

- $1,2k for the powder-coated set staggered -- $1,7k for my original set

- $2,5k for both sets + shipping costs


IMG_2397 by PATT, on Flickr
IMG_2396 by PATT, on FlickrIMG_2395 by PATT, on Flickr
IMG_2439 by PATT, on Flickr
IMG_2440 by PATT, on FlickrIMG_2441 by PATT, on Flickr

Close up -

IMG_2442 by PATT, on Flickr
IMG_2443 by PATT, on Flickr
IMG_2444 by PATT, on Flickr
IMG_2445 by PATT, on Flickr
IMG_2446 by PATT, on Flickr
IMG_2447 by PATT, on Flickr

Inner Barrels -

IMG_2469 by PATT, on Flickr
IMG_2470 by PATT, on Flickr
IMG_2471 by PATT, on Flickr
IMG_2472 by PATT, on Flickr
IMG_2473 by PATT, on Flickr
IMG_2474 by PATT, on Flickr
IMG_2478 by PATT, on Flickr
IMG_2479 by PATT, on Flickr

Stamping -

IMG_2480 by PATT, on Flickr
IMG_2475 by PATT, on Flickr
IMG_2476 by PATT, on Flickr
IMG_2477 by PATT, on Flickr


I appreciate the interest,

Patt

[SneauxM3]

Thread updated.

Found a wheel manufacturer that is curious to attempt to match oe finish, as they specialize in diamond-cut machine polishing apparently.

[alwaysbored786]

Thread updated.

Found a wheel manufacturer that is curious to attempt to match oe finish, as they specialize in diamond-cut machine polishing apparently.

Curious as to if this has gotten anywhere? I have some ltw stamp and staggered i'd want refinished to OE.

[SneauxM3]

I’ve taken them a wheel by, but didn’t have them start since some unforeseen expenses came up.

The plan is to let them give it a try on the stamped 8.5” wheel I have, as I’d prefer to get a GT replica made out of an OE wheel. But as mentioned, took the one over there, showed them images of a GT wheel. Owner said that it would be no problem, however, doing the finish into the stamped lettering would possibly not happen.

Tried to message some of the others in community that put the effort into the knowledge behind these things, but no response. So if I get it figured out, I’ll pass it on.

[SneauxM3]

Bump it up.

Still sitting in the car-parts room after going to a bbk - nothing has been refinished as of yet.

[SneauxM3]

Was thinking about these again, and not sure if I want to stay with LTWs.

bump