Hey guys!
I've been after a gauge holder that suits the e23 well. I've seen the ones that go under the ash tray area but never really liked how they sat down there. I never use the ash tray so I figured I'll use that space.
I had this made and will be test fitting it sometime next week. It is 3d printed and textured to mimic the dash material (it's not exact, but looks decent so far!)
If you guys are interested, I can have them made to order. Pricing is still being worked out due to the limited amount that would be interested.
When your enemy is making a mistake, do not interrupt him.
Very cool, interested in pricing and to see some test fit photos
Not my style, but I will buy one or a few to help the project.
I make E23 parts.
09/1983 745i (stolen spring '13 around Houston, TX Achatgruen on nutria buffalo. 8481080)
10/1984 745i
11/1984 745i
11/1984 735i (10:1-265/6)
Ford, MB, and GM round out the pack.
Awesome!! I'm in.
Count me in. I recently had this same thought, but you are much more motivated than I am.
Steve H.
Subscribed
Don't know if I'm a buyer but very interested to see how it looks.
--Jay3->Sic gorgiamus allos subjectatos nunc
84 €735i manual, 88 528e/i
Motronic 1 and 1.3 wiring
Transmission & Diff gearing sheet
Prototype needs some refinement, but the concept is sound. Will be resizing the design and reprinting for a better fit.
He is going to get the side trim pieces made to match so it all flows well.
Here are the preliminary test fit pictures.
When your enemy is making a mistake, do not interrupt him.
Looking good!
4_gauge_anodize-small.JPG
Here's one that I made about 15 years ago, probably Eric has one
ANDRE LIVES!!!!!!!!
Pavel and I have a 3D print of it coming along. Also a junk center console to test fit before we make them.
I make E23 parts.
09/1983 745i (stolen spring '13 around Houston, TX Achatgruen on nutria buffalo. 8481080)
10/1984 745i
11/1984 745i
11/1984 735i (10:1-265/6)
Ford, MB, and GM round out the pack.
Yes Hi Eric....I'm still here although currently without a 745i or E23....
If you plan to remove the wood trim on either side, just make the gauge holder 1 piece with 2 or 4 holes for power windows.
That will eliminate the very obvious transitions between the pieces.
--Jay3->Sic gorgiamus allos subjectatos nunc
84 €735i manual, 88 528e/i
Motronic 1 and 1.3 wiring
Transmission & Diff gearing sheet
I used a piece of wood and did something similar. No longer using this set up. Had the adjusting knob for the waste gate mounted top middle.
Would look nicer with matching gauges, but this worked well for me.
Disregard all the dirt.
Current: '88 E28 ///M5 Schwarz/Natur | '84 E23 745i Arktisblau/Biege | '95 E34 525iT S50/5 AlpineweissIII/Pergament | '11 E70 X5 Alpine/Savannah | '05 G55k Schwarz/Schwarz
Past: '83 E28 533i/5 Schwarz/Schwarz | '85 E23 745i Diamantschwarz/Buffalo | '95 E34 540i/6 Hellrot/Pergament | '00 E39 ///M5 SchwarzII/Schwarz | '15 RAMME 1500 4x4 Sport Weiss/Schwarz
Not sure if it will help anyone but I have this one out of the car at the moment. I could get it mocked up if I knew where to go here in New Orleans. I could also send it out as well.
Sent from my iPad using Tapatalk Pro
That looks real nice.
Sent from my HTC6545LVW using Tapatalk
hey bra...
I'm from Nawlins and you have the first production batch of my console!!
Are you the original owner o did this come with your car?
Andre
Bookmarks