I was in need of end links and did not want to drop $100+.
I ended up making my own and did a few extra sets. I used my set, sold one and have another set left over!
$75 shipped + PP or friend and fam
If they sell and more are wanted, shoot me a PM!
The top bolts are slightly larger and stronger than factory so the holes on the stock bracket need drilled to 3/8". Takes about 5 minute while changing them.
- - - Updated - - -
Okay the order is in. Heres some details for you guys if interested.
Details -
The bracket bolts are grade 5 zinc plated with a 60,000lb shear strength.
The nuts for the bolts are grade 8 zinc plated 1/4 inch
The top swivel end is Zinc plated rated at 3,950lbs radial max at 12 degrees - carbon fiber, self lubricating lining on the joint
The threaded rod is 18-8 stainless steel
The securing nuts are thin grade 8 zinc plated
The lower shank end is zinc plated rated at 3,950lbs with a 50 degree swivel (states will need lubricated occasionally for best life) I use marine grease and have not had to reapply.
The washers are grade 8 zinc plated steel
The lock washers are grade 8 zinc plated steel
I could have used cheaper materials and cut the cost way down, or used the premium SS stuff and charge what most shops do for mild steel, but this is a good compromise. They will def withstand corrosion, function well and wont break the bank. This info was added to the original post.
Last edited by PITT M3 RR; 08-21-2017 at 01:43 PM.
Bump for a solid part from a good dude - these do just as well as the adjustable ones on the market, for a much better price.
Sent from my iPhone using Tapatalk
PITT M3 RR - Im interested Pm'd you sir
Replied!
What's the range of adjustability on these? Like on the shortest setting from hole to hole and the longest setting from hole to hole?
Also, can these be used with OEM swaybars? A lot of the endlinks out there are for aftermarket sway bars only.
Hi, Ill grab some measurements for you ASAP. At the moment its for after market sway bars only as they have a hole vs the rod. Only think I can think to do is find a unit that has a hole with a similar diameter to the stock sway bar end...then have it slip fit with some sort of way to secure it.
do you still have some?
Sent from my 831C using Tapatalk
Yes guys, I can have a few sets ready to go this week. When I hit the garage tonight I will et those measurements for you too. Just set an alarm.
Just to let you guys know, I went to the garage and realized I sold all the sets I had. I am getting the supply for three more and will have it this week. Sorry about that! I though I had one set, but sold it locally awhile ago.
Lets go with $75 Shipped for the good of the community!
Okay the order is in. Heres some details for you guys if interested.
The bracket bolts are grade 5 zinc plated with a 60,000lb shear strength.
The nuts for the bolts are grade 8 zinc plated 1/4 inch
The top swivel end is Zinc plated rated at 3,950lbs radial max at 12 degrees - carbon fiber, self lubricating lining on the joint
The threaded rod is 18-8 stainless steel
The securing nuts are thin grade 8 zinc plated
The lower shank end is zinc plated rated at 3,950lbs with a 50 degree swivel (states will need lubricated occasionally for best life) I use marine grease and have not had to reapply.
The washers are grade 8 zinc plated steel
The lock washers are grade 8 zinc plated steel
I could have used cheaper materials and cut the cost way down, or used the premium SS stuff and charge what most shops do for mild steel, but this is a good compromise. They will def withstand corrosion, function well and wont break the bank. This info was added to the original post.
Last edited by PITT M3 RR; 08-21-2017 at 01:41 PM.
sweet! I defiantly need a pair! don't want to go and pay ground control for some lol
I'm in no rush by the way, for the project
Ready to go 3 sets.
they can get down to 3.5 inches with a single nut.
Last edited by PITT M3 RR; 08-22-2017 at 10:51 PM.
No prob!
Have some more - been running them with out complaints
Bookmarks