Noise and risk of exhaust into cabin. Getting it under car would be better. Will sound like dump truck with no exhaust.
I think im going to make my wastegate lines out of 1/4" hard brake line w/ compression fittings at wastegate and charge pipe. Sound good to all?
Yeah he had hard lines and some coupler thingy that the hard lines fit into I didnt quite follow. I think a 1/8 npt -> 1/4" compression fitting at the WG and tapped into the charge pipe will work well.
Route them properly and no issues. Put them in DEI sleeves or tubes if concerned. Turbo since 2010, rubber WG and boost controller lines, no protective covering. No issues.
1989 535i - sold
1999 M3 Tiag/Dove - sold
1998 M3 Turbo Arctic/black - current
2004 Built motor TiAg/Black - Sold
2008 E61 19T Turbo-Wagon - current
2011 E82 135i - S85 Swap - current
1998 M3 Cosmos S54 swapped Sedan - current
1998 Turbo: PTE6870 | 1.15 ar | Hp Cover, Custom Divided T4 bottom-mount, 3.5" SS exhaust, Dual Turbosmart Compgates, Turbosmart Raceport BOV, 3.5" Treadstone Intercooler, 3.5" Vibrant resonator and muffler, Arp 2k Headstuds | Arp 2k Main studs | 87mm Je pistons | Eagle rods | 9.2:1 static compression, Ces 87mm cutring, Custom solid rear subframe bushings, Akg 85d diff bushings, 4 clutch 3.15 diff, , Poly engine mounts, UUC trans mounts W/ enforcers, 22RPD OBD2 Stock ECU id1700 E85 tune, 22RPD Big power Transmission swap w/ GS6-53
1989 535i - sold
1999 M3 Tiag/Dove - sold
1998 M3 Turbo Arctic/black - current
2004 Built motor TiAg/Black - Sold
2008 E61 19T Turbo-Wagon - current
2011 E82 135i - S85 Swap - current
1998 M3 Cosmos S54 swapped Sedan - current
1998 Turbo: PTE6870 | 1.15 ar | Hp Cover, Custom Divided T4 bottom-mount, 3.5" SS exhaust, Dual Turbosmart Compgates, Turbosmart Raceport BOV, 3.5" Treadstone Intercooler, 3.5" Vibrant resonator and muffler, Arp 2k Headstuds | Arp 2k Main studs | 87mm Je pistons | Eagle rods | 9.2:1 static compression, Ces 87mm cutring, Custom solid rear subframe bushings, Akg 85d diff bushings, 4 clutch 3.15 diff, , Poly engine mounts, UUC trans mounts W/ enforcers, 22RPD OBD2 Stock ECU id1700 E85 tune, 22RPD Big power Transmission swap w/ GS6-53
Just got a new Borg Warner S256...
Sx. Why?
SXE is the billet compressor wheel latest badassness. The S256SX is still a great turbo at an insanely good price.
Isn't that a small turbo ?
Like smaller than gt3071 ? Or am I looking wrong ? For a 3.2L
In precision terms 5661
Last edited by Butters Stoch; 12-11-2015 at 08:33 PM.
1996 332IS
Built 3.2
CES/Steed TS Precision 6466, spraying a "$π!℅" load of meth.
Technique Tuning 80# tune.
1/4 mile 10.84 @ 136.72
Your 1 and only stop for all your BMW performance needs
WWW.CESMOTORSPORT.COM
Its a 500whp turbo that should spool fast as hell.
1989 535i - sold
1999 M3 Tiag/Dove - sold
1998 M3 Turbo Arctic/black - current
2004 Built motor TiAg/Black - Sold
2008 E61 19T Turbo-Wagon - current
2011 E82 135i - S85 Swap - current
1998 M3 Cosmos S54 swapped Sedan - current
1998 Turbo: PTE6870 | 1.15 ar | Hp Cover, Custom Divided T4 bottom-mount, 3.5" SS exhaust, Dual Turbosmart Compgates, Turbosmart Raceport BOV, 3.5" Treadstone Intercooler, 3.5" Vibrant resonator and muffler, Arp 2k Headstuds | Arp 2k Main studs | 87mm Je pistons | Eagle rods | 9.2:1 static compression, Ces 87mm cutring, Custom solid rear subframe bushings, Akg 85d diff bushings, 4 clutch 3.15 diff, , Poly engine mounts, UUC trans mounts W/ enforcers, 22RPD OBD2 Stock ECU id1700 E85 tune, 22RPD Big power Transmission swap w/ GS6-53
1996 332IS
Built 3.2
CES/Steed TS Precision 6466, spraying a "$π!℅" load of meth.
Technique Tuning 80# tune.
1/4 mile 10.84 @ 136.72
Your 1 and only stop for all your BMW performance needs
WWW.CESMOTORSPORT.COM
What is a turbo with great spool (500 lbs rwtq by 4000 rpm) and that will make 650 rwhp at 25 psi on 93 pump plus meth on a 9.0:1 S52?
Last edited by vollosso; 12-11-2015 at 09:38 PM.
1989 535i - sold
1999 M3 Tiag/Dove - sold
1998 M3 Turbo Arctic/black - current
2004 Built motor TiAg/Black - Sold
2008 E61 19T Turbo-Wagon - current
2011 E82 135i - S85 Swap - current
1998 M3 Cosmos S54 swapped Sedan - current
1998 Turbo: PTE6870 | 1.15 ar | Hp Cover, Custom Divided T4 bottom-mount, 3.5" SS exhaust, Dual Turbosmart Compgates, Turbosmart Raceport BOV, 3.5" Treadstone Intercooler, 3.5" Vibrant resonator and muffler, Arp 2k Headstuds | Arp 2k Main studs | 87mm Je pistons | Eagle rods | 9.2:1 static compression, Ces 87mm cutring, Custom solid rear subframe bushings, Akg 85d diff bushings, 4 clutch 3.15 diff, , Poly engine mounts, UUC trans mounts W/ enforcers, 22RPD OBD2 Stock ECU id1700 E85 tune, 22RPD Big power Transmission swap w/ GS6-53
Someone check out this compressor map of a s256 over a 35r compressor map. Pretty impressive IMO. https://www.google.com/search?q=borg...UMpUWLUmz8U%3D
My goal is a quick spooling and reliable 400-450whp set up. I was never going to feel right about having that "mystery" turbo , and this BW should give me peace of mind, hella quick spool, and enough power to meet my goals. Hope I made the right choice
Last edited by rajicase; 12-12-2015 at 02:30 AM.
Bleed your cooling system http://forums.bimmerforums.com/forum....php?t=1709482The ULTIMATE OEM Alarm/Keyless thread http://forums.bimmerforums.com/forum....php?t=1792200
Does the BW256 fit the TCD manifold better or worse?
I think the 256 is more of a comparison to the 3076
http://honda-tech.com/forced-inducti...3076r-2220363/
1996 332IS
Built 3.2
CES/Steed TS Precision 6466, spraying a "$π!℅" load of meth.
Technique Tuning 80# tune.
1/4 mile 10.84 @ 136.72
Your 1 and only stop for all your BMW performance needs
WWW.CESMOTORSPORT.COM
Bookmarks