I have install m3 us cluster in my 93 325i m50b25 non EWS
I want to change odometer from mile to km.
I try 3 program but it fail
gt1/dis vmware v44
-dis woek perfect can coding but when I try programing I got "VIN and ZCS/FA cannot read out from EWS/KMB/LSZ control unit!"
sss progman v32 Got it. progman not work with ads interface
-I'm stuck at "The vehicle order/central encoding key (FA/ZCS) is being determined"
ncs expert
-run expert mode
-reading kmb (instument cluster) module
-try to edit FSW_PSW.MAN file in ncs dummy
-edit and export to FSW_PSW.MAN and change job to SG_CODIEREN and execute job with no error.
-but my odometer still in mile
-I reading kmb module again and try to edit FSW_PSW.MAN with notepad
-I got problem it should have WEGSTRECKE_EINHEIT but not have
I'm use tiny ads interface with real serial port laptop in windows xp
Can someone help me
Thank for advance.
sorry for my english.
update
my current vin is incorrect
Do I need to change my vin?
Last edited by mintth; 09-22-2015 at 10:45 AM.
Weird.
Can you post the kombi file?
~Mike
First I'm open ncsexpert and select REVTOR profile
2 click VIN/ZCS/FA
3 click ZCS/FA f.ECU
4 choose e36
5 choose KMB (CKMB,EWS not respond)
6 click back
7 select KMB(instument cluster)
8 popup cbd name KMB_E36.C27
9 change job to CODIERDATEN_LESEN
10 click execute job
11 open ncs dummy select chassis e36 load FSW_PSW.TRC and select module KMB_E36.C27 (another module EX KMB_E36.C25 .0 .1 can't edit and got error )
12 distance unit has uncheck?
13 I have try to edit in FSW_PSW.TRC and not found distance unit
14 I'm looking in profile edit
15 I'm check distance unit to km in ncs dummy and export and verify in FSW_PSW.TRC with notepad
16 re open ncs expert and change job to SG_CODIEREN
17 execute job and look at my cluster is writing
18 but when complete is still in mile
If I do somthing wrong please tell me.
my real vin is ZBTCB45080AA46103
but in m3 combi is WBAAA00000AA46103T
what is T mean?
under my hood my vin is +AA46103+
Should I need to change my vin first before coding?
thank for advance.
Last edited by mintth; 09-23-2015 at 12:30 PM.
CODIERUNG_ERFOLGT
codierung_erfolgt
CODE_NR_2
wert_01
CODE_NR_3
wert_01
SIA_AUS_VERZOEG
wert_01
SIA_TEMP_FAKTOR
wert_01
DZM_FAKTOR
wert_01
LICHT_EINSCHALT_DAUER
wert_01
WARNUNG_GESCHW_AUS_ZEIT
wert_01
LICHTWARNUNG_AUS_ZEIT
wert_01
LICHTWARNUNG_EIN_ZEIT
wert_01
DATA_VALID
datensatz_gueltig
TANKGEBER
hebelgeber
GETRIEBE
automatik
K_ZAHL_WEG
4663_imp/km
K_ZAHL_WEG_KOMPL
4663_imp/km
STEIGUNG_EINSPRITZ_KENNL
m52b28
MOTOR_FAKTOR
3_imp/umdrehung
CODE_NR_1
nicht_aktiv
CODE_NR_4
wert_01
CODE_NR_5
wert_01
GURTWARNUNG
aktiv
GURTWARNUNG_GONG
aktiv
LAENDERVARIANTE
ece
TANK_KENNLINIE
kennlinie_01
TANK_DAEMPFUNG
kennlinie_01
OELTEMP_GAS
oel_temp
TANK_GAS_KENNLINIE
nicht_aktiv
TANK_GAS_KENNLINIE_WINKEL
nicht_aktiv
SIA_GRENZE_INSPEKTION
30.000_km
SIA_GRENZDREHZAHL
4512_u/min
LICHT_EINSCHALT_VERZOEGER
wert_02
SIA_GRENZE_ZEIT
0_tage
SIA_ANZEIGEPARAMETER
ohne_zeitinspektion
OELSERVICE_ANZAHL
2_service
GURTWARNUNG_AUS_ZEIT
wert_02
GURTWARNUNG_EIN_ZEIT
wert_02
WARNUNG_GESCHW_LIMIT
nicht_aktiv
WARNUNG_GESCHW_EIN_ZEIT
wert_02
ZUENDSCHL_WARN_AUS_ZEIT
wert_02
ZUENDSCHL_WARN_EIN_ZEIT
wert_02
BC_CODE_AKTIV
aktiv
TANK_SCHALTPUNKT_1
wert_01
TANK_SCHALTPUNKT_2
wert_01
TEMPERATUR_KENNLINIE
kennlinie_02
SCHWELLE_UEBERDREHZAHL
8000_u/min
Have you ever solved the issue?
I'm having the same problem but with engine mode. Car is 318i and has now M62B44 in it. Need to set impulses per stroke from 2 to 4. Coding goes fine (KOMBI says EEP1 / EEP2) seems that it is written but once read again it fails.... (still same).
Bump up the thread. I am in the same boat as mintth
Is there a solution how to chaneg mileage from miles to kilometers in E36 M3 Instrument Cluster?
Bookmarks