Page 3 of 4 FirstFirst 1234 LastLast
Results 51 to 75 of 86

Thread: Vorshlag 2002 BMW E46 325Ci - Daily/Track Car - Project Jack Daniels

  1. #51
    Fair's Avatar
    Fair is offline Senior Member Supporting Vendor
    Join Date
    Oct 2003
    Location
    Dallas, Texas
    Posts
    3,634
    My Cars
    E36 M3, E36 LS1, E30 318
    continued from above

    The NASA National office folks were there to observe with rumors of NASA Nationals here? Couldn't find a better place to host a major NASA event at the country's only active track on the F1 schedule. The facilities are immense and world class! I guess when you spend $450M to build a track that is to be expected.

    I wore my driving suit all day Saturday and part of Sunday, but shed the soaking wet garment late Saturday when I was feeling the heat. Its not the safest way to drive on track obviously but neither is passing out from sweating so much you get heat stroke. I hope the organizers remember how hot it is in late May/early June when they plan this event next year's calendar. This far south it gets HOT quick.



    Traffic in the TT sessions was pretty rough. I don't know why its so hard for drivers to get off line and give a point by when you are holding someone up, or on your cool down lap. I have never seen a NASA TT event this bunched up, on a track this huge, in all of my years with this organization. We had over 45 drivers, but not everyone was driving in each session. If I felt like I was holding anyone up I would bail on that lap and point them by - obviously I had made a mistake on that lap, or they were just faster. The sooner they got around me the sooner we could settle into our class / grid rankings and get clear laps.



    Saturday's "TT session 1" (our 2nd session of 4 that day) was a good bit faster for me than the Warm-up, with a 2:43.932 lap, mostly just learning the lines from Costas' notes. I went out again in TT session 3 but the ambient temps were so high and traffic SO BAD that I never got a faster lap time. I skipped session 4 due to the temps being at 96°F after lunch, and my total lack of energy by that time. Still coached Amy and instructed my student.



    By day's end that 2:43 lap was enough to win the 5 car TTD class by 1.5 seconds and set the first ever TTD track record here (this was NASA's first event at this track). After this hot day I drank the best cold beer I ever had! We were goofing around and found cutouts of the F1 drivers so of course I had to get a shot on the F1 podium with Hammy. We stuck around to get a trophy but skipped the Saturday night "party crawl" to go to dinner (inside air conditioning, with lots of water refills) with friends Joe D (SI racer) and his family (including my student), plus American Iron racer Stewart M. After that meal I slept like a rock that night.

    SUNDAY TT

    Up early again for the 7 am HPDE meeting for Amy, then I lined up on grid to look for a better time in the coolest temps of the day - Sunday was once again "the money session". Unfortunately there were 4+ cars gridded ahead that were holding me up badly between T2-T10 and again in T13-T19 in the opening laps. There are such long straights with so many turns in between here that the "momentum" cars like TTD really do have to fight the powerful cars for track space. It didn't help that we had some "TT Tourists" giving ride-alongs in the TT competition session, driving laps 5+ seconds off their normal pace - who couldn't give a point by to save their lives. I complained to the higher ups but got a "Too bad - go faster" response. I managed a 2:42.848 lap making a pass in heavy traffic, temporarily giving us a 4 second lead over 2nd place.



    For TT session 2 I talked to the 3 guys gridded behind me and told them I was going to build a massive gap (100+ yards) to the slower cars gridded ahead of us on the out lap. This might give us a lap without being held up in the twisty bits. Now we're not supposed to do this gap trick, but people aren't supposed to block either - so we did what we had to do. "Too bad". I still caught them by the T2-5 complex on the first lap, then backed way off and let 3 cars behind me go by. I let them get ahead for a lap, built another gap, then found a good chunk of time. I ran my best time of the weekend of 2:42.340 this way, but it was still hotter than the ideal track conditions of the first session.


    Video from Sunday Session 2 - best lap of the weekend

    As you can see in the video above I wasn't exactly happy with that lap, and there were multiple driving mistakes that cost time. The rear tires were also struggling by that point - too hot, too many heat cycles, just never "came in" in this session. I was slower in the esses than in previous sessions, just finally was able to patch together a quicker lap without all of the traffic. I never really got a lap all weekend where I nailed all of the high speed braking markers, clipped every apex, used all of the track out room, and maxed out what the car could do... a combination of learning the track, TRAFFIC, tire age, TRAFFIC, little driving mistakes, TRAFFIC, and track temps. These factors combined to never allowed me to sync up what I felt the car should do (2:40-2:39) on a "full tilt" lap. Oh well, maybe next time.



    I still had nearly a 4 second lead over 2nd place after session 2, and with the rising ambient/rack temps and my level of sweating I felt we had seen the best track conditions already - so I skipped TT session 3. For once I gave Amy the car (she always ran right after me) without blistering hot tires and brakes. Now she could work on her lap times (she was still "gaining courage" up until the last session) without boiling tires. The 2nd place TTD car was an NC Miata that had aero and power - he was pulling me on the straights - but luckily was braking super early and going slower in the esses. He was usually gridded 1 or 2 cars behind me and could see my lines, and I could see that he was getting faster. He went out in TT session 3, found a bunch of time, and got within a second of me?! Uh-oh.

    OK so now we have some serious competition, this time from someone out of region I don't know, and I have one session left to stay ahead. Do I go out, do I skip it? Will he? If he finds any more time in session 4 I could not only lose for the day (and potentially 2 tires) but lose the track record (which I had reset in session 2). I went to grid for TT session 4 with some serious pressure, but no other cars were there yet (see below left) when we were scheduled to go out - just me. Maybe I could get a "solo session" and work on my lines, maybe still find some time in this late afternoon heat? Slowly more and more and more TT drivers arrived to grid, and my closest TTD competitor was supposed to be gridded right behind me. If he showed up to grid I was going to stay out there in front of him for the entire time, to see what he could do.



    With a long delay due to a Spec Miata crash the last TT session was stuck sitting on grid for an eternity - 45 minutes passed in sweltering high 90s heat, and by then 10 TT drivers had arrived. I stayed on grid, looking for that TTD Miata. 5 minute warning. 3 minute. 1 minute. No Miata. Right before TT took to the track DARK clouds rolled in (see above right) from a looming MEGA storm.

    Amy said "He's not coming. You won - now go out there and drive!" So I did. I drove the piss out of the car, knowing I had a fresh set of tires coming from Hoosier for the next race. Held nothing back, pounded out laps. And consequently had the most fun of the weekend with no pressure any more. I narrowly missed a TTC S2000 spinning right in front of me entering T10 on the first lap, but other than that I finally had my first traffic free laps of the weekend. With this set of Hoosiers essentially cooked out (with a combined 5 weekends of driving among 3 drivers) I still managed to run a 2:43.5 lap in the highest temps of the weekend. I stayed out a long time, just stringing corners together, pushing the car more and more. This track is LOTS OF FUN!



    I finally came in when I started to run out of fuel (the long T16-T18 corner would fuel starve with anywhere near 1/2 tank) and Amy was watching live times on the Race Hero app. She said none of the other TT cars went any faster, so we took the Sunday win and track record for the weekend. Hot damn! They had some champagne and trophies for Sunday class wins also (I guess $1200 entry fees pay for a lot!), but we rushed to load up all of our stuff in the garage, stuck the car in the trailer, and high tailed it outta Austin by 7 pm with rain starting to fall. We weren't a mile from the track when the skies UNLOADED and we slogged through one of the worst storms I've ever driven through.



    Plenty of traffic heading north through construction so of course we had a trailer tire explode. It happened during a 10+ mile construction zone with no shoulders, right outside of Waco. Brand new tire, not a month old. GRR! I quickly dove into one small stretch of shoulder 100 feet long, stuffed the right side of the trailer almost in the dirt, then did a super fast tire change in the rain with traffic whizzing by. Super sketchy location with no way to exit back into busy high speed traffic without backing up and getting a spotter - it was on a curve with concrete barriers on both sides. Texas DPS pulled in behind me right as I finished the tire change (to our last spare!) and helped make a lane for Amy to pull the truck and trailer out into. Well its time for all new wheels AND a new brand of tires on this trailer, and two new spares.

    Luckily the following Monday was a holiday for most folks (our shop was closed) and we got to catch up on some sleep before I headed in to catch up on work. Watched some of my laps, noted the massive traffic and blocking, but I've got to just realize that without the Friday test day I put myself in a bad spot by having to learn the track during competition. With a better Saturday TT Warm-Up time I could have moved up the grid ahead of the slower cars sooner, avoiding much of the traffic. Can't take any new track for granted - we have to learn them at a test day.



    Amy (see above) had a lot of fun and was running her fastest times of the weekend right at the end. She was finally getting more seat time in this 330. Its hard to share a car that is also running in competition, because tires are a very finite, temperamental aspect. We really want to get her car (FRS) more track worthy and try to sell this 36' trailer and get a 2 car (44-48') for next year. We'll see. My DE1 student learned a TON and I got him a check ride for DE2, which he passed easily - probably ready for 3, but I won't rush him. Great racing, well run event, and other than the high temps, the weekend was a complete success. If they move NASA Nationals here.... man that would rock!!!

    COTA Official Results: http://timingscoring.drivenasa.com/N...ts/May%20COTA/

    The Sunday results are being contested in TT (one of the other class entries magically dropped 20 seconds in one session) but the Saturday results are up and our class results were not protested. This pair of class wins put us at 600 points for the year, and the next closest TTD racer is at 255 points. We'll run "D" at Hallett in late June and if we can continue our unbeaten streak and score two more wins (+200 total) that would put us far enough ahead in class mathematically to cinch the regional championship. We have some new 245mm Hoosiers coming that we won at COTA so at least we won't be on this dead set of tires any longer. Our E46 here isn't going to NASA Nationals East or West - two tracks I have never driven and that are super far away - so Hallett might be our last TTD event, then the car might jump up to TT4 soon after.

    WHAT'S NEXT?

    I've been hinting in this build thread about a possible move from TTD to TT4 for a while. The "TT-Number" classes are much more open and almost entirely P-to-W based (compared to the "dying or gone" TT-Letter classes). We'd need a big injection of power, a big drop in weight, or a bit of both to get from the 14.25:1 ratio of TTD to the 12:1 ratio of TT4. So we're working on both aspects now while still staying in TTD for one more event. TT4 allows us to have a splitter, wing, LSD, a max of a 275mm R7 tire, and more power (without chasing "mod points") so it is very enticing.



    To get a head start on TT4 prep a lot is going on with our little E46 this week. I will cover this work next time but we have already added an AJ Hartman carbon fiber hood, AeroCatch hood latches, HARD Motorsport rear quarter Lexan windows, a Lexan rear window, aluminum rear bulkhead, dual fuel pump upgrade, and more. All of this is currently TTD legal, and we can easily ballast-up to meet the TTD weight, but these mods do help us get closer to TT4 later.



    Our sister shop HPR race builds engines. Since I race with an M54B30 engine... and so few shops build these up... I've been pushing the guys to look at these a bit closer - with an eye towards a 300 whp engine. So last week we began tearing apart an M54 to look at what we can do to make that power level or beyond. Master engine builder Erik Koenig took a lot of measurements and ran a lot of numbers on this block & crank and we think there is a lot room for a "considerable amount of additional displacement" in this all-aluminum M54 engine - more than I have ever heard anyone reaching. I will talk more about this next time and over the summer as we explore the possibility of a more powerful M54 engine. If we don't like the costs or constraints within the block or head, we can always put a small displacement LS engine in this car (like a de-tuned 4.8L) to make the numbers we need.

    Until next time - drive fast and take chances!
    Last edited by Fair; 06-13-2017 at 09:09 AM.
    Terry Fair @ Vorshlag Motorsports

  2. #52
    Fair's Avatar
    Fair is offline Senior Member Supporting Vendor
    Join Date
    Oct 2003
    Location
    Dallas, Texas
    Posts
    3,634
    My Cars
    E36 M3, E36 LS1, E30 318
    Project Update for July 17th, 2017: Since our last update in June our crew did a number of upgrades to the red 330, including a carbon fiber hood, Aerocatch hood latches, HARD Motorsport Lexan quarter rear windows, a Lexan back window, and a custom aluminum bulkhead for the trunk to cabin opening. We even show carbon fiber repair techniques this time.



    These weight removal changes required us to add more ballast to stay within TTD class rules, but its all part of the planned move to TT4 later this year (where we can run less weight/more power/more aero). To reduce our fuel load reduce our fuel load requirements and fuel starvation issues in right hand turns we also performed a popular upgrade by adding a 2nd fuel pump. The driver's seat was also upgraded with a halo style racing seat. As predicted, the more "racey" the 330 gets the less "daily driver" friendly it becomes.



    We took the 330 to the NASA Summer Shootout at Hallett and won all 3 Time Trial events over the weekend and set two new track records, which we will cover below. This brings our TTD track record total to 5 for the year in this car. This actually wasn't an easy weekend and we had some tight competition chasing us.



    We will also cover more of the upgrades to "Operation Track Rat", an E46 328i sedan we bought a while ago. This update shows the suspension upgrades, brake upgrades and chassis reinforcement. This car recently sold but I will continue to share all of the work we did before this customer took ownership. I recently bought yet another E46 coupe that we're going to tinker with, to keep a steady stream of E46 cars coming into Vorshlag.

    NOTE: We have closed down the thread on corner-carvers, as they don't want build threads posted by shop owners there anymore. Hope you found your way to this thread from another location.

    CARBON FIBER HOOD UPGRADE

    Please suffer me this small tangent to explain how our 330 got a carbon hood. The E46M3 V8 monster track build we are building for a customer received a lot of AJ Hartman carbon fiber parts, including the roof panel and hood. The quality, weight, fit and finish were all exceptional.



    But getting this sizable part from New Jersey to Texas proved to be a bumpy road and one hood was damaged in shipping. A second hood was sent for this M3 and got here in perfect shape. So we had one extra, damaged hood on hand. Hmm, what could we do with it? Shipping it back costs a lot of $$, and its always tough to sell a repaired carbon fiber part - the weave will never "look perfect" again.



    Above is some tool (me) holding the AJ Hartman E46 carbon hood with one hand. I cannot do that with the stock steel hood on the 330, I assure you! This hood weighs 1/4 of the stock piece, and we needed to concentrate on front weight removal, so this might be the right mod for our red 330 right now.



    44.5 pounds vs 9.5 pounds, so this would shed around 35 pounds. Weight saved over the front tires, and fairly high relative to the cg. Too good to pass up...

    CARBON FIBER REPAIR

    To be able to use this hood we needed to repair the shipping damage. Ryan used to work on carbon fiber race cars so he knew what materials to order. Carbon fiber fabric plus the epoxy resin and hardener to set it up. He also had me order some heavy gaffer tape, which was used to hold the outer shape of the repair during curing.



    Now I've done fiberglass repair before but this was a little different. We aren't going to be painting this hood for a little while so we didn't want to do any bodywork on the repaired section just yet. The key to this repair was to get the repaired area on the outside to match the shape of the hood as much as possible.



    The cracked section was cut back a bit to trim up the fibers at the break. This was so the cracked area would line back up - otherwise the pieces would try to mesh together at a funny angle. Patches of carbon fabric were cut in increasing widths, with the thinnest patch near the crack, then a wider one above that, for about 4 layers. The first batch of resin was mixed up in a disposable measuring cup.



    The material pieces were soaked with the mixed resign, which was applied to the broken area in layers - thinnest, then wider, then widest on the outside. Some resin was brushed onto the hood section first, too. Gaffers tape was placed on top of the repaired area while it was still wet. Then some formed aluminum pieces (made beforehand) went on top of the gaffers tape, which acted as a press on both sides of the repair. Clamps were placed against the aluminum and it was allowed to cure for 6 hours.



    The same repair was done at the end of the day on the outside surface of the hood. Resin, material, gaffer tape, aluminum plates, and clamps to give it pressure. Then that cured overnight.



    Above left is the broken section repaired on the back side only. Above right is the finished repair with the outer patch completed, which was somewhat smooth. This area will be cleaned up with some bodywork before paint, but is functional and strong. With $80 in materials (and lots left over) and a couple of hours of work we salvaged a pretty busted up section of the carbon hood. Like all motorsports grade dry carbon parts it needs to be painted or wrapped, and we plan to paint this and some other panels on the car later this summer.



    The hood was bolted on using the factory hinges and lift struts but you will notice the underside only has about half of the inner structure. The forward portions are omitted for weight reasons. This is meant for race cars, not street cars, and no provisions for the two forward factory latches were there.



    Instead Ryan added two Aerocatch hood latches. Installing these takes a lot of measuring, careful cutting, some drilling, and patience.



    Similarly the hood pin instillation is a bit harder than it looks. These have to be mounted at the precise location to line up with the hood latches, with the correct height and angles to align with the latching pin. The mounting holes were reinforced with TIG welded plates and the threaded fasteners for the pins have good anchors to hold against now. A small section of rubber hose act as adjustable hood height spacers, as well as a good cushion against the closing of the hood. Works great.



    This is how the raw hood looks right out of the mold, with no clear coat, no heavy gel coat. So while I wasn't planning on buying this lightweight hood the shipping damage and repairs we did made it more affordable, and it will help us as we move this car to TT4 class. For now we'll have to add 35 pounds to the ballast rack in the trunk.

    MORE ON THE E46 TRACK RAT BUILD

    Back in the June 9th 2017 update I showed the first stages of mods to this 328i sedan, which is becoming a dual purpose street/track car.



    As we've shown in this thread before the easiest brake upgrade to any E46 322/325/328 is an upgrade to the E46 330 front brakes, which are 1" larger diameter rotors. We had previously upgraded our 325Ci (the original #JackDaniels) to 330 front brakes and noticed quite a nice improvement. So when the red 330 (our TTD car) got an a front BBK upgrade to Powerbrake bits we took the fresh 330 rotors/Carbotech pads/330 calipers off the red car and donated them to the 328i here.



    The Stoptech rotors and Carbotech pads were fresh and had only done 2 events on the 330 since new, so they went right on. The 330's calipers also looked fine, so those and the longer 330 caliper brackets were transferred over. The 328i got a full brake flush with Motul RBF600 and an upgrade to our 90mm wheel studs and lug nuts (I hate lug bolts!).



    Right after this brake system upgrade it was time for suspension. Again, new parts we had briefly track tested on our red 330 were put to good use on this 328i, like the Bilstein PSS kit we had converted to 60mm coilovers.



    "Waste not, want not" - these very same Bilsteins had been on the red 330 for the first 3 track weekends and still looked brand new. We had robbed the camber plates and spherical rear shock mounts so those were replaced with new Vorshlag bits on this 328i. We re-used the Hyperco 60mm coilover springs (450F/550R) and the modified Bilstein rear ride height adjustable platforms from the red 330, too.



    There is always the Achilles Heel of the E46 to fix: the rear subframe mounts at the chassis. As we have discussed before, these can crack easily on any E46 car and must be reinforced for all street and track cars. Without these reinforcements an E46 is hard to sell; with them done correctly the value goes way up.



    We break in all new fabricators who start at Vorshlag on an E46 rear reinforcement job. Its dirty, nasty work and requires hours of overhead wrenching and TIG welding. We let them do their first one on shop owned cars - because the hours can run long on your first attempt. If they can pull this off without complaint and their welds look good, they usually work out.



    With the subframe out we always replace the sloppy rubber bushings with poly or aluminum. This car got Powerflex Black race polyurethane in the 4 subframe mounts and two front and one rear differential mounts. No more slop to wreck havoc on the rear sheet metal.



    Once the rear subframe was all buttoned up in the car the front control arms were replaced. The front lower control arm bushings at the "lollipop" were replaced with Powerflex 2-piece race poly bushings as well. We always drill and tap the housings for grease zerks and drill thru the outer part of the 2-piece bushing to allow grease to get to the inner joint. That wraps up the brakes, suspension and subframe reinforcement - we will show more work on the 328i next time.

    ALUMINUM REAR BULKHEAD TO TRUNK

    We showed the welded custom 4-point roll bar in the red 330 back in a previous update to this thread. I have been very happy with the fit and rigidity of this 1.75" x .095" wall DOM tubing structure.



    continued below

  3. #53
    Fair's Avatar
    Fair is offline Senior Member Supporting Vendor
    Join Date
    Oct 2003
    Location
    Dallas, Texas
    Posts
    3,634
    My Cars
    E36 M3, E36 LS1, E30 318
    continued from above

    When we remove the back seat and add a roll bar like this there is an open hole left to the trunk. If we had a fuel cell mounted in the trunk there would NEED to be a metal firewall added close off the fuel tank from the passenger cabin. Of course the E46 has the stock fuel tank under the back seat floor section, so a metal barrier already exists. I noticed a lot more road noise (and a clunk we later traced down) with the back seat out, so I asked our guys to build an aluminum bulkhead - to quiet this noise and make the car look more finished.



    Ryan usually does these sheet metal jobs and as usual he made this task look easy - which it isn't. He started by making templates from heavy craft paper, which were then transferred to .080" thick 3003 aluminum sheet. This structure is made in 3 pieces - an upper shelf, then a 2-piece vertal panel that fit around the rear down bars of the 4-point roll bar.



    These were cut, bent, and drilled for mounting hardware. The panels were designed to work with bolts and threaded inserts (see below right) - but in this step the familiar Cleco fasteners were used during construction.



    Now since we weren't building an air tight firewall the panels were fitted close to the roll bar tubes but this will still help keep fluids and gases out of the cabin from the trunk - whatever those might be.



    As you can see the rear window was out to gain access to make this series of panels. With a coupe of coats of semi-flat black paint (to minimize glare in the back window) the final panels were bolted in place using a number of stainless button head bolts and M5 threaded inserts added to the chassis. Very happy with the finished panels, looks great.

    LEXAN QUARTER REAR AND BACK WINDOW UPGRADE

    In an effort to remove more weight and to test out some additional parts from the vendors we work with, I ordered the HARD Motorsport rear quarter windows and a Lexan rear window from 5 Star Bodies. I didn't weigh the factory rear glass or the replacement panel, which was a silly mistake.



    The back window was fitted to the car, holes were drilled for hardware, then the border was masked off and painted semi-flat black.



    The border has to be taped off and masked. Taking your time here makes a big difference in the final look. The holes in the rear window frame had M5 threaded inserts added, but the painted border on the Lexan panel covers up these areas and the body colored sections you might otherwise see.



    A bead of black weatherstrip adhesive was laid down before the Lexan was put in place. Countersunk stainless M5 bolts went in above countersunk Tinnerman stainless washers were inserted into the holes drilled in the Lexan to make for a flush mounted hardware installation. Now it was time for the rear quarter windows. This car also had a bad OEM rear actuator for the stock glass windows (these weigh .5 pounds each).



    The glass pieces weighed 11.2 pounds for the pair with the actuators, the Lexan added up to 3.6 pounds, so it isn't huge savings potential but it all adds up. These come with a cut vinyl border so you don't have to mask and paint them like we did the back window.



    The OEM pieces were easy to remove - a few bolts on the front edge hinges and then the actuators which also unbolt. Then the weatherstrip gasket was pulled out of the channel.



    The mounting brackets and hardware that came with the HARD kit made the install very easy. We save over 7.5 pounds with the Lexan side quarter windows. I am extrapolating (uh-oh!) that to the rear glass to Lexan upgrade to be closer to 15+ more pounds dropped, since we threw out the old glass and didn't weigh those bits...



    50 additional pounds of ballast was added to the trunk to get the 330 up to the weight we wanted, which is 25 pounds over the 3205 pound number we are claiming in TTD class (we are burning 6 class points to dip 80 pounds under the 3285 pound class minimum for this car). This is with a 1/2 tank of fuel and the 210 pound driver in place. This made for 51.2% front weight bias, which is the best we've seen in this car since the beginning.

    DUAL FUEL PUMP UPGRADE?

    The factory plastic fuel tank assembly for the E46 chassis is a "dual saddle" design, shown below. This is how many modern sports sedans and coupes run their fuel tank (our 2011 Mustang had a nearly identical design). It puts the fuel under the floor sheet metal, usually under the back seat. It straddles the driveshaft and exhaust with a raised center portion. Fuel is usually fed from one side by an in-tank fuel pump but there is usually a feed tube that goes to the other side, fed by a jet pump or vacuum. The E46 fuel pump (with a level sender) is on the right side and a second fuel level sender is on the left side. The two level senders "average" the readings to send to the fuel level gauge on the dash.



    Most of the road courses we frequent are built to be run in a Counter Clock Wise direction, a layout which produces mostly left hand turns. These turns push the fuel into the right side saddle, which helps to keep the E46's fuel pump pickup covered in fuel. Right turns would slosh the fuel load into the left side saddle, possibly uncovering the fuel pump pickup....



    Fuel starve on right turns in this car has been noted at some tracks but hasn't been a huge issue in this car until we ran COTA, which had one massive right hand turn. Turns T16-T18 are linked to make for a fast, 4th gear, flat out right-hander that would starve the fuel pump on anything less than 3/4 tank in our 330. Running 3/4+ tank is a LOT of fuel, which we could "just run as ballast" but we are trying to get weight down for the next class. It was time to tackle this right hand fuel starve issue.



    There are numerous kits sold by various shops for a "dual fuel pump" upgrade, where the left side fuel level sender is replaced with a 2nd fuel pump which has another integral float and level sending unit. We looked at the options and decided we could make a better kit for less. The pictures above show the fuel sender and jet pump on the left side and the other round port is where the fuel pump resides, in the right side saddle portion of the tank.



    Now one thing we noticed when Aaron had the factory sender and jet pump line (internal crossover hose) out of the car was that the feed line to the "pump side" of the tank was kinked, hard. Maybe we just had a restriction in the factory bits? But so many other BMW owners complain of the same issue that this couldn't be just a kinked line affecting this car. So we moved ahead with the second fuel pump addition - and this kinked hose was replaced in the swap..



    Wiring in the second pump was fairly straightforward but plumbing it took some new lines and a custom adapter fitting. This was machined from aluminum and allowed a connection with some crimped Oetiker hose clamps for the feed line. I'm not exactly sure how other dual fuel pump kits do this, but this made the most sense to us. Both fuel pump feed lines were connected via a "Y" and feed the main supply line running to the fuel rail.



    This feed line is then routed over to the other saddle, under the floor, as shown above left. An internal crossover for the return was made inside the tank using submersible fuel line - specially made so the outer jacket is impervious to continuous submersion in fuel (which makes it damned expensive). With the two steel access covers bolted in place (above right) it is all secured under metal bulkheads. With 1/2 tank of fuel verified visually before buttoning this all up we were set to test this at Hallett, which has some fast right-handers on the CCW course and where the entire course would be run CW for one session Sunday...

    SPARCO CIRCUIT II SEAT SWAP

    The stock seats that came in the E46 330 look a bit "sporty" but in reality they are terrible. Downright scary on track, especially once you have real race tires and race suspension. We yanked these heavy bastards out early in this build (and they went into the 325Ci "JackDaniels").



    We have been racing this 330 with a COBRA Suzuka GT width driver's seat for the past season and a half. This is a great seat which we have used in multiple shop cars over the years. This Kevlar composite 1-piece FIA racing seat has higher leg bolsters than the Sparco EVO II seat that is on the passenger side. These hold your legs better in cornering but make for a higher "step over" when getting in or out. It makes it more challenging to use in a daily driver, but it is a better racing seat because of it.



    I like COBRA seats but in the last year we have setup a better relationship with Sparco, and have begun stocking and selling more of their seats. The Sparco EVO line of seats (they make a total of 4 versions... EVO I, II, II US, and III) are very popular and probably comprise 80% of our sales. The E46 M3 SMG below got a pair of EVO IIs for dual purpose street/track use.



    Since we had no seat in the right side of our 330 for a while I decided to add a a Sparco EVO II there. Since this 330 stays at our shop I can let customers who stop by test sit in our 330 in this seat.



    We ran our 330 with the COBRA on the driver's side and the OEM seat on the passenger side for a while. Then we pulled the heavy passenger seat out to try to make weight, and ran it with just one seat for a while. For the last ~6 months or so it has had this Sparco EVO II on the passenger side using a fixed mounting bracket (no slider). It is more than adequate for the occasional passenger - I usually take my HPDE students, friends, customers, or Amy for ride-alongs. And I've ridden in this right side seat with Amy driving many times, too. Works great.



    As the #DailyDrivenTrackCar E46 becomes more "racey" with Lexan, Carbon Fiber, and an offroad-only exhaust, we have been increasing safety to match the speed of the entire package. The 4-point roll bar ("half cage") was added, and while technically suitable for a dual purpose car, this is one of those things that cannot be un-done easily. These things are all adding up to make this into a race car, and I'm OK with that. That means some aspects of street driving naturally get compromised.



    One thing we just added that really is not appropriate for a street car is the halo-style Sparco racing seat on the driver's side. This Circuit II seat helps prevent neck and head injuries in a side impact with this massive chunk of seat surrounding your head. The Sparco Circuit also has very high leg bolsters, for leg protection, like the Cobra Suzuka.

    continued below

  4. #54
    Fair's Avatar
    Fair is offline Senior Member Supporting Vendor
    Join Date
    Oct 2003
    Location
    Dallas, Texas
    Posts
    3,634
    My Cars
    E36 M3, E36 LS1, E30 318
    continued from above



    Compared to the Cobra and EVO II (above left), the Circuit II (above right) weighs about 3 pounds heavier. Of course we weighed them, who do you think this is???



    I've been keeping 2+ Circuit II seats in my lobby because they are going into more and more race cars. I've sat in these 4 Sparco seats dozens of times and the Circuit II just fits me best. The Pro2000 is a good alternative to the Suzuka, with better hip/leg bolsters than the EVO line. Between the Pro-ADV and Circuit, the head halo comes inches higher on my head on the Circuit. The seat fits my frame and we decided to pull the Cobra driver's seat and add the wider "II" version on a new, stronger slider & bracket assembly.



    Last year when we first installed the Cobra driver's seat I had Olof make a super low profile bracket and trimmed the carpet around the factory floor mount structures. With the stock headliner and sunroof in the car I needed every possible inch of headroom. Some of you criticized this bracket and it wasn't as rigid as I like, so we built an all new bracket using much thicker materials this time.



    This chassis bracket is built with 1x2" rectangular tubing and angle iron and is about an inch taller than the original. With the retracting sunroof and headliner removed height is no longer an issue and at the new seat height Amy can finally see over the dash. We uses the same Cobra dual locking slider and modified OMP side brackets. The old chassis bracket was light and thin, whereas the new bracket is beefy and could kill a man if you swung it at his head. Unsurprisingly the new bracket keeps the seat more rigid in the car.



    The Circuit II is the Kim Kardashian of racing seats, with a much more curved bottom (see below left). This is why I fit better in this seat than the PRO-ADV, which visually has the same height as the Circuit II but a flat bottom. Mounting this Circuit II required some adjustment in the side brackets - which we did after I ran the car at Hallett - to get the seat height correct for me. Since this seat was added about an hour before we left for the race, I ran it at Hallett sitting a bit too high for my liking - but it was still a great fitting seat.



    Now that we had a few more minutes to modify the side brackets and change the mounting holes, it is adjusted better to my torso height and I can't wait to get back on track with this seat. The slider is super smooth and locks positively.



    We left the OEM 3-point seat belt anchor off of this set of brackets, and that along with the halo seat's natural blind spots make street driving a thing of the past. #BecauseRacecar The car still has a steering wheel airbag, steering wheel radio controls, a radio and front speakers, and an ice cold AC. Some tough decisions lie ahead for this red 330.

    BRAKE PAD LIFE

    Before we loaded up the car to tow to Hallett we had the car on the lift for a quick pre-track check-up. We pulled the wheels, checked the brake pads, caliper temp strips and rotor tamp paint.



    The Powerbrake PB23 compound pads that came in our "large 4 piston" front Powerbrake upgrade kit seem to be lasting an insanely long time. after 14 months and countless laps the Powerbrake front pads are still 3/4 depth! Its crazy - I abuse these brakes, and they are wearing very well. I'm used to replacing pads every 3-4 weekends, but it might be every 2 years at this rate.



    Even the rear pads seemed to be wearing better than expected. Maybe with the massive upgrade to the front brakes it took some work/wear off the rears. And even through we won some tires at COTA, we only won 2 total, so the existing tire set was examined and looked OK to run one more time at Hallett.



    With the large number of "little upgrades" and the car checked out by our staff I felt confident in the upcoming Hallett Race. There were 5 signed up in TTD so I was hoping the class might "make" - but many were strangers from outside of our region so I had no idea if there were some new folks that could challenge us.



    With the car and gear loaded into the trailer, Amy drove us out of Dallas around 4 PM on Friday for the 4-5 hour tow to the hotel in Tulsa Oklahoma, about 40 minutes from the track. We would blast out to the track early the next morning to unhook, unload, and get to grid.

    NASA SUMMER SHOOTOUT, HALLETT, JUNE 24-25, 2017



    Hallett opens the gate early, but to get into the paddock area you have to crossover the track surface, so they close the track by 7:30 am and you would have to wait to enter between sessions after that - sometimes for as long as an hour. Yea they need a bridge or a tunnel, but it has worked for 30+ years this way.



    The track is built in a way that it can be run in both directions, but predominantly they run it CCW. And NASA runs it this way for the racers, HPDE and TT groups - except for the last sessions on Sunday for HPDE and TT. Oddly enough NASA Texas Region counts the last ClockWise session as a separate event, and track records can be set in this one and only session. They do it as a way to get people to stick around for the last Sunday session, but points is points and track records are my favorite thing, so we ALWAYS stick around.



    I've set track records at the 2013 and 2014 NASA Summer Shootout in our red Mustang above. Some folks are intimidated by one particular corner, T9, which is called "the Bitch". A number of cars have had big shunts there, but I love that corner and always seem to be caching competitors there. I'm on/off the gas and brake 3 times entering T7/T8/T9, usually jumping two different curbs on the entry. We always come away from this NASA Hallett event very pleased with this track - the lush green rolling hills, the elevation changes (which we don't see much in Texas), and the amazing track officials and photographer Tim - he always takes great shots! I bought the photo CD from this event like I do every year. If you see a non-watermarked pic in this post, it's from him.

    SATURDAY RACE #1 - 1.8 CCW

    Saturday we got to the track and quickly unloaded the car, setup the camera and lap timer, and installed the AMB transponder. Tire pressures were 28psi cold all around to start shooting for 33F/32R hot. The Time Trial group started with a meeting, and we had a large number of folks there. So I figured TT would be a mad house of traffic with only 1.8 miles of track.

    Event Photo Gallery: https://vorshlag.smugmug.com/Racing-...ne-24-25-2017/



    And sure enough, traffic in the TT warmup session was a hot mess and I only ran a 1:29.1, stuck in a lot of traffic (I'm used to 1:21 times here in the Mustang). That time at least moved me up to 11th on the grid out of 26 that made it to this session. I had a TTD competitor that was close on my heels with a 1:29.5 in a white Acura Integra Type R. Ambient temp was a low 73°F, which is crazy for late June in the south, so we were loving it.



    In TT session 1 the temps dropped to 71°F ambient, and my times dropped down to a 1:27.983. The whole time I was fighting to get a clear lap inside of a huge a pack of TTC S2000s. That was the fastest TT session of the day - but I still felt like I had more in the car. The white Integra popped off a 1:28.108 in that session - whoa!



    That margin was too close for comfort so I lined up for TT session 2, where temps had crawled up to 82°F. Once again had to fight for track space with faster cars ahead of me that were holding me up in all of the braking zones and into T9. All I could muster was a 1:28.032 in the ever increasing heat. The TTD Integra slowed down to a 1:29.904 best lap, which was a big drop off for him.



    There was still less than a tenth of a second between us, so I went ahead and ran the last TT session of the day Saturday in fairly hot conditions (86°F), not expecting much improvement - but the competition was too tight to sit this one out! I found a break in traffic and on lap 4 ran off a 1:27.950 for Saturday's best. It was only .027 sec quicker than my TT session 1 time but good enough for the win and a new TTD track record.



    I walked the paddock to go look at this Integra Type R but couldn't find him, so I figured I'd look again on Sunday. TT competitors can ask to see other TT racers' classing sheets - and I just wanted to take a peek and see where his points were spent. Having never seen an Integra run competitively in TT before I was just curious. We had four TTD cars run during the day but one got DSQ'd in the Warm-up, so only 3 on the class results at the end of the day - which meant "no tire payout" for the win once again.



    Overall the car did well that day, just needed more horsepower to get some passes done. The only good place I found to pass was under braking into T2, which is a fast downhill braking zone. But if you pass there it throws you offline for T3 and you lose a lot of momentum going up the hill into T4 so it blows the lap. All day I was picking off TTC, TT3 and even TT1 cars in the early laps where I could, trying to move up the grid. Inevitably some of those folks would put in a flier at the end of a session and sneak past me on grid the next time. Frustrating being down on power.



    Even with only 86°F showing it was hot and humid at the end of the day and Amy and I both needed to cool down. There was a "paddock crawl" party and even fireworks, mostly attended by folks camping at the track. Since we had a hotel with air conditioning 40 minutes away we jetted back to there, cleaned up, and had a nice meal downtown instead.

    continued below

  5. #55
    Fair's Avatar
    Fair is offline Senior Member Supporting Vendor
    Join Date
    Oct 2003
    Location
    Dallas, Texas
    Posts
    3,634
    My Cars
    E36 M3, E36 LS1, E30 318
    continued from above

    SUNDAY RACE # 2 - 1.8 CCW

    Sunday we got to the track right before they closed the gates at 8 am, whew. We had 3 sessions to get our best lap in on the 1.8 mile CCW circuit. I got to grid and began looking for the white TTD Integra. He never showed, hmm? Even with lots of traffic I went out and ran a 1:27.592 in the first session, taking 7 laps looking for a clear track. It was 79°F but temps were climbing fast after this session.



    In the video above from this session I can see many driving mistakes, especially my line into T4 and entering T5. Hindsight is 20-20 and all but even at the time I knew I was butchering the late apex at T4. Just couldn't get my brain to turn in later on this uphill, blind, off camber corner. Frustrating, but I still found nearly 1/2 a second from my best times Saturday - which is what the AiM predictive lap timer kept telling me I could run.



    I went out in TT session 2 but it was getting hotter (82°F) and the tires were getting greasy quickly. There was no traffic and I ran my best lap of the session (1:28.274) on my first lap, with times steadily slowing down after. I also ran a few laps in the HPDE 4 session that followed taking Jeremy W for a ride-along, running some 1:29.1 fun laps.

    Nobody was dropping time, so I skipped TT session 3 when it was getting into the low 90°F range - and everyone slowed way down. The fuel starve issue was as bad as ever and if the fuel load was anywhere near 1/2 tank it would fuel starve in T9, the long right-hander. Meanwhile one of our E46 M3 suspension customers Dennis Clevette (below) won the TT3 class and reset the lap record to a 1:20.385 - Nicely done.



    My lap in my first session CCW lap was enough to win the 3 car TTD the class by 7 seconds, with a new TTD/PTD Miata competitor joining the fray for Sunday (the Type R never showed up). I was saving what was left of this ragged set of tires for TT session 4 - our only ClockWise session of the weekend. I've only run this CW course twice - in the last session of the 2013 and 2014 NASA events.

    SUNDAY RACE #3 - 1.8 CW

    This last session was damn hot but since it was worth another 100 points and a potential track record I was going to run it. To complicate matters many of the Houston and Austin NASA officials were leaving a bit early to get a jump on the 7-9+ hour drives home they had. Our TT director asked me to step in and run that session.



    So I got to grid and talked to all 10 of the TT drivers, giving out copies of the map and showing folks who had never run this way where we needed to "bunch up" and "go green" on the out lap. I also tried to show people where to watch out, brake early, and not to mess up (T3 entry done wrong will put you across the track outside of T2!). Amy and I then filled up the 330 with the very last of our Texas 93 octane fuel we brought, for 3/4 tank indicated. This is the fuel load that worked on the CCW course without starving so far. I felt like the car would be fine even with all of these right-handers...



    Since I was helping folks on grid I was the last driver to get belted into their car, HANS linked up, gloved up, timer turned on, vidcam started, etc. I waved the field by while I was getting strapped in and caught the back of the field on the out lap, bringing up the rear. Even with only 10 cars running this CW session I had a LOT of traffic to get through and I spent the entire session trying to find a clear lap. And fuel.

    The fuel starve issue was HORRIBLE running ClockWise, even with 3/4 tank! It fuel starved on Every. Single. Corner. My best lap came on lap 7 of 7 with a pitiful 1:31.158, fuel starving its guts out, short shifting, and making 2 passes on that lap. Driven well and without all of these other issues the CW direction should only be about 1 second slower, not 3.5. Still that was good enough for another TTD win (+100 points) and another track record. The lap is so bad I'm not even posting it, yuck. Obviously we need to revisit the fuel system setup.



    To help fill in for the HPDE group leader, I came back into the grid area after my last TT lap, quickly parked under a tree, jumped out then helped get the last session HPDE drivers (also their only CW session of the weekend) up to speed, passing out the maps and telling them what to look for on this course run in this unusual direction. Once they got going on track I checked the results and noticed that of the 7 TT track records reset this weekend our little 330 set 2 of them. The old CCW TTD record was a 1:28.6 and the old CW record was a 1:36.6, so we reset them both by enough. Our TTD times were pretty far off the new TTC records set by Wallace, but that's been his M.O. all year - obliterating the old TTC records in his dyno-reclassed S2000 (below left).



    By the time I got back to our trailer, parked by the pond at the back of the paddock near T9 (above right), the heat was pretty brutal and Amy had overheated a bit (she took pics and helped me in the car all weekend, but didn't drive any sessions). We loaded up the E46 and hit the road soon after, with 3 wins and 2 new track records under our belt.



    Jamie Beck's ST3 classed Mustang did well on Saturday scoring two 1st place finishes. In Sunday morning practice 3rd gear on his second Getrag MT-82 transmission broke, but he could still run the whole course in 4th. He still managed to score two 2nd place finishes in the next two races, putting him in the points lead for the season. We have a T56 Magnum XL being built now that we will install in this car soon.



    The recently added cool suit / cooler / controller we added to his Mustang worked perfectly, even with the CoolShirt "vest" he ordered from us. With as bad as the heat has been affecting me lately I need to get one of these setups. Oddly enough the high temps at Hallett didn't kill me this time, but I also wasn't doing double duty with instructing and racing.



    While at Hallett I looked at a friend's 48' aluminum gooseneck trailer and fell in love. It has a generator, air con, queen sized bed, room for two cars - gotta step up to one of these some day. My 36' trailer is now for sale...

    WHAT'S NEXT?

    Obviously we need to take another look at the dual fuel pump "upgrade" and see if we routed something wrong or if this is just normal when you corner at 1.3g lateral. If we find a flaw on our layout we have a test event coming up where we can check with various fuel levels. If not it might be time for an external surge tank/pump setup, like the LS1 powered E36 M3 (see below) we are plumbing now.



    A fellow TT competitor was chatting with us in our paddock and noticed two small issues at the Hallett event - a ground strap had broken and the Mishi air filter had started rubbing the radiator support. Not much of a concern, and I did some quick paddock repairs for that weekend, but I'll show the real fixes for these two items next time.



    There's a good long break before the next NASA event, which isn't until late September at TWS (either on the regular 2.9 mile CCW course or this 1.8 mile abomination they are threatening to make us use). This break is done because Texas summers are damned hot and it will be 90-100°F for the next 2 months. People get heat stroke racing in those conditions. We'll spend that time working on our little E46 building it for TT4, of course. I'll try to show another update here before that event. There are some other big surprises in the works as well. Stay tuned!

    Cheers,
    Terry Fair @ Vorshlag Motorsports

  6. #56
    Fair's Avatar
    Fair is offline Senior Member Supporting Vendor
    Join Date
    Oct 2003
    Location
    Dallas, Texas
    Posts
    3,634
    My Cars
    E36 M3, E36 LS1, E30 318
    Project update for October 3rd, 2017: I am way behind updating build threads; I need to do about 5 other project updates but I am going to try to do a quick update here. We had a busy summer, which pushed back some work my red TTD prepped 330, but we finally did some upgrades in mid September.



    Not only did the front bodywork and aero completely change on the red TTD 330 (above), we completed and sold two of the other E46 cars we have been chronicling in this thread: the 325Ci "Jack Daniels" coupe and the Track Rat 328i sedan (below). This time I will show the final round of work on JD and the 2nd round on the silver 328.



    We also picked up another E46 coupe, this black 2003 below. We are just now starting to work on repairing the "little things" to create another "reliable daily driver" for Amy and I to use while some of our other cars are in the shop for upgrades.



    I won't talk about the black 325 Coupe above this time, but I will cover work to these other three E46 projects in this post - plus one NASA race weekend - while trying to keep it as brief as possible.

    ROUND 317 OF JACK DANIELS REPAIRS + SOLD

    This little "whiskey dented" E46 Coupe E46 started this whole build thread, which we named Jack Daniels. It needed a lot of repairs - too many to count - and I lost money on this car due to the purchase price + parts costs alone. I quit counting hours long ago, because it was ugly.



    Learned I should have learned long ago - no matter how cheap a car seems up front, starting with a high mileage car coupled with excessive repair costs can bury a project into a money loser right from the beginning. This car needed everything when we bought it with 200K miles: interior work, body work, paint work, suspension work, gaskets/leak fixes, clean-up work, entire cooling system, headlights, and all of the normal things that can plague any high mileage E46.



    Even with a shop that specializes in BMWs, and friends in the industry hooking us up on things like PDR repairs, and wholesale pricing on repair parts, I really blew the budget on this one. I won't say how many thousands I lost on this build, but it was enough to notice.



    In the end we really cleaned up this little 325 Coupe, and made somebody a nice daily driver that they got with pretty much everything touched or repaired. It had some upgrades that we did when this was going to be our TTD build - the 330 front brakes, Powerflex bushings, etc - and Amy used this is a daily driver off and on for 2 years.



    I had people who read this thread that kept calling to try to buy this car for months, but I kept finding things I wasn't happy with and wanted it to leave my shop only when I felt it was "right". So when I drove it recently and felt the rear diff bushing slop, I had our new tech, Aaron, install Powerflex poly diff bushings in all 3 locations (see above). The OEM rubber is just so soft and cracked that this will give whoever buys it less trouble back there.



    One nagging thing that kept bugging me was the flaky fuel level gauge. It would only read "full" for a few miles after you topped off the tank, then it would ready empty for 3/4 of the gauge sweep. There are TWO fuel level senders and I ordered the primary one that comes with the new fuel pump, shown above. Our crew swapped that assembly in and it fixed the gauge, whew. Notice also: no more dash lights! We only put 7,000 miles on this car in 2 years, but whenever its logged over 200K it still kills the resale value.



    The leather seats (which came from my red 2001 330Ci) needed a bit of work and Brad used LEXOL conditioner to clean and condition the fronts as well as the rear seats. The car was then washed, detailed, vacuumed - cleaner than it ever was while in our possession. I finally felt good about letting this one leave and let the next guy that called have it for a decent price.



    When it was time to deliver it to the new buyer he ended up with a lot of repaired systems and a clean, reliable car that is fun to drive for not a lot of money. It won't win any car shows but it should put in many thousands of street miles without too much trouble. It might become the basis for his next WRL endurance race car build in the next few years also. #LongLiveJackDaniels

    TRACK RAT GETS SOLD, CUSTOMER WANTS UPGRADES

    I have talked about the silver Track Rat build in the past. This was a 1999 BMW 328i sedan we bought a while back for another purpose (endurance racing), but when priorities changed I just used this car to fill time in the schedule when our techs weren't on billable work. Which is rare, but still. Last time I showed the 330 front brake upgrade to this car, the Bilstein coilover suspension install, rear subframe reinforcement and bushing upgrades done in late 2016. Let's cover another round of work that happened in 2017: the interior.

    INTERIOR: ALUMINUM DOOR PANELS, FLOORS, CONSOLE, ROLL BAR, SEATS



    Our crew that started tearing this car apart one weekend (when I wasn't here), to make it into an endurance race car, literally ripped apart and threw away perfectly good interior panels and seats. When we aborted that plan and I decided to make this into a dual purpose street/track car to sell, we needed to keep the windows. Question: how do we cover the door openings on the inside? Answer: fabricate all the things!



    Ryan made some 3D aluminum door panels that tied into the felts at the top and bolt to the doors around the perimeter. These were a little tricky to make and no, we won't likely make a production version. The C shaped cut-out at the front is to clear the dash. The "bump" out of the upper section is to clear the power window motor.



    The seats were tossed during the interior removal, too. We stock a lot of race seats here so I had Ryan build brackets and a slider to hold the Sparco Circuit II on the driver's side. Notice how ugly the naked transmission tunnel looks, above?



    I got stuck with this unusual and LARGE Momo FIA seat shown above when it didn't fit into a customer's Miata. Plenty of room for wider seats in an E46, so it went into the Track Rat. It uses a fixed mount and fits virtually anyone on the passenger side.



    The center console was thrown out also - along with ALL of the window switches, DSC switch, hazard switch, etc. This made me "less than happy" so I had one of our techs make a new center console. It wasn't exactly a fabrication masterpiece but it does the job. Again, this was back when it was just another car we had and I was trying to get it into shape to sell.



    The missing switches were purchased (GRR!) and then holes were made to mount them into this aluminum console towards the end of the build. This way the hazards worked, windows rolled up and down, etc. The early E46 uses a DSC button that is different than the late cars... so this was purchased and installed as well (see below). Way too many hours tied up into this aluminum console - if you want to keep it JUST USE THE OEM PLASTICS instead.



    The carpets were gone and with that a lot of padding that covers up a funky floorpan shape and lots of big wiring bundles.



    To cover up the "non-flat" floor and hide the wires a pair of "false floors" were built from aluminum sheet. Underneath is a lot of structure to keep them from buckling under the weight of a driver's legs, which is not shown. A custom "Dead pedal" foot rest was added along with some "Grip tape" (above) to keep your shoes from sliding around on the floors when wet.



    I don't like installing fixed back racing seats into a car without at least a 4-point roll bar. A bolt-in kit was ordered from Kirk Racing, and it shipped in on a flat pallet in pieces. Ryan fitted the roll bar structure to the chassis, tack welded the rear down tubes in place in the car, then removed it to final weld these joints.



    The welded assembly was powder coated in a "textured black", then it was bolted into the car. Even the reinforcing backing plates were powder coated before installation. All in all it fits pretty well, with a gap to the roof and B-pillars that allows for this to be installed with a headliner and interior panels. Great place to hang harnesses from...



    Well it turns out when you are building a car "on speculation" of selling it, you probably shouldn't install racing seats and assume it will fit the buyer. The Circuit II wasn't the right seat but we had an EVO III in stock that fit him perfectly. This was installed into the Track Rat and the new Circuit II that was in there went into my red 330, which I showed in the last installment. A pair of new Schroth Profi-II 6-point harnesses went in to wrap up the safety/interior bits.



    A bit of PDR was done early on in this build to remove some dings and a "wrinkle" in one door panel. Kris did a great job and made this car look pretty sharp - it had good paint, just needed a little massaging.



    Next time I will show the upgrades the customer asked for after he purchased the car. It now looks like this, above. We have since tackled the wider wheels/tires, flares, oiling system upgrades, cooling system changes, custom brake cooling, new belts/hoses, Vorshlag motor/trans mounts, new Motul fluids, plus some other small repairs and a few more little restoration jobs. This car has already seen track use and the owner loves it. He can drive to the track with cold air and windows up, then get there and let 'er rip. It turned into a more dedicated track car interior, and a better dual purpose build than even our 330...

    continued below

  7. #57
    Fair's Avatar
    Fair is offline Senior Member Supporting Vendor
    Join Date
    Oct 2003
    Location
    Dallas, Texas
    Posts
    3,634
    My Cars
    E36 M3, E36 LS1, E30 318
    continued from above

    NEW FRONT NOSE + SPLITTER FOR TTD 330

    In the last installment we showed a carbon hood upgrade and new seat on the red 330, so it was a bit lighter than before. We had to add back some ballast (which came out when we put in the 4-point roll bar) to meet the 3205 lb weight we were claiming with driver (I had crept up to 217 lbs in the spring, yikes). That 3205 number is 80 lbs under the "base class" weight of 3285, so we have been burning +6 TTD class points to take this 80 lb drop all season. This was because we couldn't figure out exactly what to do with those points...



    The 330 did well enough at Hallett in June (2 wins + track record) but we had some really close TTD competition (Acura ITR). Being so far under the TTD class / build "theoretical power" max of 244 whp (at 3285 pounds) is hurting it's competitiveness (only making 216 whp with header, exhaust, CAI, stock tune). A 28 hp power deficit is huge, but we didn't have any points left to make the stock M54 engine substantially more powerful, legally. We were also hitting a brick wall with the BMWeditior software (more on that below) and finding someone locally to tune it to maybe find another ~10-15 whp wasn't panning out. Even "tuned" we could still be 20+ hp short of the class/build max. So what is left that we attack to make the car faster for TTD, that can also apply to TT4 class next year? (TTD is going away)



    Downforce! To go faster in the corners we need some help from the air, and we have been wanting to add a wing + air dam + splitter to this 330 build since the very beginning. Aero upgrades helped us find a lot of lap time in our TT3 Mustang, but when the "powers above" inexplicably pulled 7 points from the "E46 330" listing in Jan 2016 (the TTE -> TTE* fiasco) it crushed most of my "aero dreams". We spent every classing point carefully, but with only 6 points left (assuming we ballasted up to 3285 lbs) we could only do a few things with aero, and none of it was "balanced":

    TTD legal Aero additions, shown with class points
    Wing = +4
    Air dam = +3
    Splitter = +3
    Front fascia change = +3 (aka: air dam)
    Canards/Winglets = +2 (not legal for TT4)
    Flat front flat undertray = +0 (from front centerline to front lip)
    Rear Diffuser = +3 (not legal for TT4)
    Vented hood / CAI = +1 (already are claiming with CAI)

    Jason and I brainstormed this part of the TTd build over many lunches for the last two years and could not come up with an aero combination that used all 6 points we had left and could give the car more balanced front/rear downforce potential. I briefly thought about a CRAZY multi-element canard/winglet setup (+2) with a flat undertray (+0) front aero package with a rear wing (+4). The rules poorly define any limits for canards/winglets, especially as to their numbers/square footage/shapes. That craziness might have worked for one event, but then a rules rewrite would have shut that down. And with a planned move to TT4 for 2018, canards/winglets are not legal there. So this would be a lot of weird front aero that could be used for a very time period, maybe not even a full weekend of TT racing.



    We also tried to rationalize taking off some mods (brakes, suspension, etc) to "get some points back" for more aero potential, but everything on the 330 now serves a purpose: to test/prove a new part or brand, to make the car faster, and/or make it easier to drive. Nothing there we could afford to lose was worth enough points to sneak in a wing + air dam + splitter. So for now we compromised and pushed for all 6 points to be used on an air dam/front fascia (+3) and full splitter (+3) instead - which could also be used later in TT4. I had picked up a number of these E46 M3 bumper covers a while back and they fit the E46 coupe perfectly. Even the HARD flares fit up to it without modifications. The original 330 nose was also pretty beat up, as pointed out by the #JankyStick above. The M3 nose had better brake inlet duct support, a larger lower grill opening, and a "more flat" lower edge for a splitter. It also looked a lot better.



    Mounting an aftermarket bumper cover to an E46 could be easier than what we did here, but I wanted to go with with a custom front bumper beam - just like we did on the E46 M3 CSL V8. It is both legal and strong and would probably be lighter, yet loses the "5 mph" bumper shock design. I figured if I hit something on track, its gonna be at a lot more than 5 mph. Aaron used a tubing roller and curved a piece of 1.75" dia DOM tubing, then made some bolt-on brackets and stand-offs, to place the curved beam under the new M3 nose.



    Maybe we could have tweaked/modified/forced the OEM E46 bumper beam & 5 mph collapsible bumper struts to fit with this aftermarket M3 nose, but I wanted something stronger and lighter, so this tubular setup was my decision. A raised sheet metal bracket along the middle of the curved beam has a flat mounting face that the bumper cover bolts to, with the recessed stainless mounting hardware hidden behind the hood/grill. Dimple dies keep this bracket light, and two more "loops" of thin sheet metal touch the underside of the bumper cover out on the ends, giving it additional support.



    The bumper cover and beam assembly were on and off the car many times for mock-up. The goal was a cleaner fit, so it was not rushed. I wanted this new nose to look good (after it is painted) and have tight body lines when completed. After it was tacked up the beam assembly was removed and finish TIG welded on the bench.



    A new OEM plastic/rubber front "radiator inlet snorkel" from an E46 M3 was ordered and installed, replacing the fresh E46 330 snorkel we had put on last year. This plastic piece seals the openings from the two "nostril" grills and lower "mouth" grill of the M3 nose onto the face of the radiator - directing air through the core. Since air wants to take the path of least resistance, without this air snorkel you would lose a lot of inlet airflow around the radiator core. The OEM engineers do a great job of making these inlet boxes have smooth lines, proper angles, and good seal, and it was much easier to buy this $153 part than make it from scratch. We often make these calculations to see when it makes more sense to buy something than to fabricate it - because time is money, for everyone, always. #BoughtNotBuilt



    By that same logic, Why not just buy a splitter kit? Guys like AJ Hartman make a beautiful carbon unit that fits this E46 M3 nose. The answer for us was that none of the worthwhile, pre-made splitters fit our class rules, especially the "new-for-2017" TT4 rules. Off the shelf splitter kits rarely fit every class or organization, and some "image brand" parts are not strong enough for real track use.

    So this time we did have to make something custom - to fit both the TTD and TT4 rules. We chose sheet aluminum for this splitter design, as we often do, for a lot of reasons. I will address this and the many of the rules we had to interpret to make the max sized splitter for TT4, below.

    AERO RULES MEASUREMENT DRAMA

    Like we find in almost every ruleset, Jason and I looked at the TT4 aero specific rules and saw things that left some "room for interpretation". In TTD the splitter can protrude past the car a full 12" forward and up to 6" wider than the body. In TT4 a front splitter can protrude 4" forward... but from where? For this event we went with a more liberal interpretation of the TT4 limits rules for our TTD (for now) splitter. Of course the internet erupted with howls of protest when I showed pictures during construction. People cannot be bothered to research the rules or class you are running in, nor want to discuss the nuances of rules that are missing definitions or key words about measurement, in 60 characters or less.



    So while this splitter "looks huge", its pretty mild for what is allowed in TT-Letter class (TTD), but potentially not legal for TT4 (depending on how they "intended" for the rule to be) by about 1-2" in the forward direction. We are building for TT4 later this season but at the very next NASA event (MSR-Houston) the car will still be running TTD.

    2017 NASA TT rule 7.3.2.D.2
    TT4 Specific Aerodynamic Modification Allowances (if not using OEM Mod Factor):
    Aerodynamic parts/devices/aides shall be limited in TT4 to the following:
    a) All of the items listed above in section 7.3.2.D.1) “OEM Aero” Modification Factor.
    b) Vertical front air dam (5º tolerance) that follows the outermost edge of the front and side bodywork/fascia.
    c) Single flat, horizontal front splitter that protrudes no greater than 4” from the vehicle.
    d) Single rear wing or spoiler that does not exceed a height of 8” above the roof line, or width greater than the vehicle’s body width, or end plates greater than 12”.
    e) Modified BTM, non-Base Trim Model (non-BTM), or replaced front fascia (unless specifically approved in Appendix D:
    i) May have nothing attached to it other than specifically allowed items (above).
    ii) May not have canards/winglets molded into it.
    iii) Any item that is molded into the fascia that functions as an airfoil, deflector, dive plane, or vortex generator and extends 2" or more past the outline of the immediate surrounding fascia is prohibited. To inspect: a plumb line run across the entire surface of the fascia and bumper shall not have any such item that extends 2” past the line when viewed from above.
    f) Cutting/removal of the rear bumper cover/fascia where it does not cover the rear frame/bumper cross beam.
    In ST4/TT4 if you don't use the "OEM" aero rules and chose to take the small p-to-w penalty (0.4) for "non-stock aero" (we will), you can build around these front aero rules shown above. Somewhat limited allowances and lengths compared to TT-Letter, and the entire section is a bit on the brief side. No canards/winglets or rear diffuser allowed (which are legal in TT-Letter). Since there is no side-limit we jump back up to regular TT1/2/3/4 aero limits, which are a maximum 6" from edge of vehicle, so a splitter can be wider than it is long front-back. About that 4 inch forward protrusion...


    Defining how and where to measure critical components is important in proper rule writing

    It doesn't say so in the TT4 splitter rule 7.3.2.D.2.c, but where do you measure "forward" on the splitter from? This is critical and can be interpreted in 3 ways: A) the projected outline of the bumper cover, B) from the base of the front fascia (and which one - OEM or aftermarket/allowed limit of the class?), or C) from the base of the allowable air dam? Since the TT4 aero rules mention "outermost edge" in 7.3.2.D.2.b, and again with a definition of how to measure "past the outline" in 7.3.2.D.2.3.iii, you'd think it was from the projected outline, right? And since an air dam is legal and effectively changes the projected outline by another 5° forward, that moves the "line of measurement" forward as well.



    That being said, this is how we measured for this splitter, which I feel is 100% legal for TT4 with the rules as written. Of course after a picture was posted on Facebook, I was told through back channels very quickly that's not what they "intended". So even though the same TT4 aero rules section defines projected outline and references it in two other places, and we can add an air dam with up to 5° off vertical that pushes that outline further, they want us to cut the splitter back considerably for TT4 use. We think... Maybe... The written rules contradict this non-official judgement. You never know how these rulings will go, but it seems to always be against how we interpret things.



    Regardless, this splitter plus another 6" of length was legal for TTD at MSR-H. For the event at the NOLA event in October we will switch classes from TTD to TT4, and there I might ask another TT4 competitor there to file a formal protest on this item, so we can FORCE an official ruling from NASA National. In writing. With a change in the rulebook for next year. This way everyone is on the same playing field in 2018.



    The splitter plane itself is .125" thick 6061-T6 aluminum, which is thinner than I normally use so I might not stand on this one like I usually do. The splitter was checked for level and ground clearance at the leading edge was ample at 87 mm (3.4"). This is a more clearance than we have done on previous splitters, like our TT3 Mustang which was closer to 2".



    Splitter height is critical, and the lower you can get to the ground plane without the splitter plane bottoming (which disrupts downforce completely), the better. But then there are other real world limits, like the issues of curbing height limiting track width (see above right) and the need to load cars into a trailer or onto a flatbed wrecker (see above left), plus body roll and brake dive / bump travel that can smash your splitter into the ground. You need to plan for this, and sometimes this is only seen in track testing.

    We let some of the chassis give us a starting point. The back of the splitter mounts at the front edge of the OEM factory undertray/engine bay brace - which is a two layer, welded, stamped aluminum structure. Nutserts were added to this and countersunk stainless hardware was added to the back edge of the splitter to secure it there. From there forward it is level - which is required (no up- or down-angle is permitted).



    Now it was time to support the leading edge of the splitter. As this splitter extends about 6" forward from the base of the bumper cover, and the plastic fascia is not a good anchor to counteract downforce loads (expected to be in the 100-300 pound range, depending on speed), we need some splitter "stays" or "struts" to hold it in place. Some folks use cables, which only work in tension, but that isn't how we do it around here.

    continued below

  8. #58
    Fair's Avatar
    Fair is offline Senior Member Supporting Vendor
    Join Date
    Oct 2003
    Location
    Dallas, Texas
    Posts
    3,634
    My Cars
    E36 M3, E36 LS1, E30 318
    continued from above

    I also wanted the struts to be mounted into brake duct or grill openings, to minimize holes in the (eventually) painted front fascia. Aaron machined thin slices of solid round steel bar with threaded holes, then welded these in 4 points to the bumper beam. The splitter struts extend through the plastic fascia and attach securely. These struts then mount at the splitter plane with countersunk hardware from underneath, with nothing to hang down and get "ground off" on pavement.



    With the bumper cover in place the #ExposedSplitterStruts are softened a bit, which a friend G-Speed gives me so much grief for. These 9" Joe's Racing Struts have LH and RH threads, which you can adjust the length of by turning the aluminum hex bar center portion. Sometimes we custom make longer units but it wasn't necessary on this splitter (see below right).



    While a carbon fiber splitter can often get by without struts, we are not a composite shop. The costs for replacing a molded carbon splitter ($2000-2500, if one existed to fit this car/class, which it doesn't) also pale in comparison to the $200 that this 4x8' sheet of 6061 aluminum sheet cost. We could cut another from our new pattern quickly. Carbon splitters also fail spectacularly - they can crack, shatter and sometimes explode in use.

    Aluminum splitters tend to bend and deform, which can be repaired track-side with a hammer or by driving over the bent piece with a truck tire. Most of the time spent on this "splitter install" (33.01 hours) was the planning, templating, bumper beam construction, bumper cover mounting, OEM inlet air snorkel swap, struts and anchor mounting, tow hook install, making the air dam mounts, adding the air dam plastic, brake inlet duct mounting, tire wall fabrication, etc. Making the actual splitter plane cut-out was probably only 2 hours.



    Now we had to fill the big gap between the bottom of the not-quite-flat M3 bumper cover and the top of the splitter plane. This was our air dam solution - some short pieces of aluminum angle (not shown) were bent to follow the shape of the fascia, riveted to the splitter, which then forms a semi-continuous lower mounting flange. Next a small strip of black plastic "race roll" was cut, marked, drilled and mounted vertically to this flange via rivets, and trimmed to overlap the fascia and fill the gap. We didn't rivet the upper face to the bumper cover, as this air dam might change, and the pressure of the plastic (after a bit of forming/heating) made for an adequate seal to the body along the top edge.


    These thin aluminum bits are "tire walls", and do not add downforce. They curve downwards

    These vertical aluminum parts added in front of the tires (above) are what I am calling "flare extensions". Its really a "tire wall", but they don't define or address this in any NASA ST/TT class that we can find. They also function as an outboard splitter support (we cut the width back from the allowed 6" down to 4", to keep the front end narrower). The black plastic fender flare (allowed) has rules that are a bit vague, so we are calling the more vertical parts of the tire walls an "air dam" (allowed) - which serves the same function here. We went to great lengths to integrate these with the HARD Motorsport flare and keep it from being a potential "canard" (not legal).


    These cars both have canards, which are meant to add downforce outside of the front splitter. They curve upwards.

    In the 71 pages of the 2017 v14.1 NASA ST/TT rules, there is no definition of a "canard" (3 mentions) or "winglet" (2 mentions) that we can find, but the motorsports world knows what a canard is and how it functions. The purpose is to take air hitting the front of the car and curve it upwards (concave shape) and force the air flow to create some downforce. These do work but are a bit drag intensive. Canards are not allowed in TT4, where we are heading with this car. What we have added onto the 330 are curved the wrong way to create downforce, and really are just missing extensions of the flare to cover the spinning portion of the tire sticking out into the air stream. No downforce generated, just operating as a fender flare for the front edge. Again, we can call the front vertical section of these "air dam" if you want - which is legal.



    A threaded coupling was machined, fitted into and welded to the bumper beam (above left) for mounting the pivoting front tow hook. Four little aluminum brackets were built to allow the OEM style grills to mount in the single-layer carbon fiber hood (the OEM steel hood has a mounting flange). These provide a function - keep big nasty rocks from flying into the heat exchangers, and the grills fit up against our M3 air inlet snorkel. Lastly a factory BMW roundel hood emblem was drilled and mounted to the carbon hood which has a depression for the emblem plus the two OEM anchors.



    That wraps up the front nose + splitter install. Below we will cover some other things that were done at the same time...

    BRAKE COOLING + NEW ROTORS

    We have been racing this car for 2 seasons without any front brake cooling whatsoever. A stock E46 330 normally has some small "scoop" plastics that sort of push air in the direction of the front brake hub, but its not very effective. And after the front hit that this car survived years before under another owner, all of those undertray, front fender liner, and brake scoop plastics were long gone or shredded. There were entire sections of the fender liner just gone - all too common for a 15+ year old car like this...



    Why did I care? We have these massive Powerbrake 4 piston motorsport calipers and 340x35mm rotors up front! Big meaty things that can soak up tons of heat and shed it all easily, right? Well after 1.5 years of abuse, and a few times where I aborted a hot lap right before the pits and came in with hot brakes, I finally warped a rotor. Amy says I came in more than once with the front brakes pouring smoke, hopped out, ran off to get in a student's car, and just left the car parked - which is what probably warped the rotors. My stupid mistake. So for the last couple of events I've had to drive around this issue, which would show up after a few REALLY hard laps and was evident with a pulsation in the pedal.



    Even though the rotors have plenty of meat left on them we couldn't find a way to safely turn 2-piece floating rotors, so we ordered replacement rotor rings and new bobbins/hardware from Powerbrake. These were installed onto the original aluminum hats that came with the brake kit. I was hesitant to put these new rings on the car until after we had some front brake cooling upgrade. And that brake cooling was waiting on the new nose + splitter decision. Now that we had a path forward, and a new front nose mounted, it was time to add some backing plates with cooling air, then feed that with some effective brake inlet ducts and hoses.



    We are developing a front brake cooling backing plate package for the E46 330 using the design above, which we created on the silver 328i shown at the beginning of this post (will show that next time). With a small tweak these backing plates cleared the Powerbrake calipers. The 3" oval hose opening shown should pump air completely inside the rotor hat, around the wheel bearing, and through the rotor ring's curved vanes like an air pump.



    We chose 3" hose for a number of reasons, but mostly because it packages well, provides cooling that is appropriate for cars this size/weight, and is a default brake duct size for most cars. Heavier/faster cars often get 4", but it is much less common on a 2900 pound BMW like this. Notice the vertical wall that has a "C" cut-out for the hose to pass around? That also acts as a splitter mount. We will go back after our next track event and add some inner fender liner sections - from aluminum or plastic - to fill in the gaps and better seal the engine bay. A clean fender liner makes a vented hood more efficient, too.



    Placement of a brake inlet duct is critical - you are looking for the highest pressure area on the nose without moving the inlets off to the side too much, where the air can roll off to the sides. These HARD Motorsport inlet ducts fit the E46 M3 nose perfectly, so a pair were purchased. Again - we can buy something for a whole lot less than the time it would take to hand-make it here. #BoughtNotBuilt The bumper beam was designed to clear these with the new nose, because all of these pieces interact with each other in the same space.


    Right: The hole shown in the duct is for the splitter strut mount to pass thru and land on the bumper beam.

    The M3 foglight openings are large and these formed thermoplastic ducts fit around them perfectly. They form a nice curved bell that pushes the inlet air into the 3" round opening, which fits inside 3" brake hose nicely. Aaron mounted these to the M3 bumper cover with rivets hidden behind the front face, for a cleaner look. The hoses route to the backing plates but care was taken to keep them from being rubbed into by the front tires steering at full lock. With a 17x10" wheel, that takes some twists and turns, and the custom vertical splitter mounts inside the wheel well have room for the hoses, but its part of the normal plan when routing brake hoses. This should keep rotor temps from getting high enough to warp a rotor ring, even if I screw up and forget to take a cool down lap after a session. (I did a full 20 minute session of qualifying laps at MSR-H with these brake ducts installed - never saw even a hint of fade or warping).



    Even with nearly 2 seasons of track events on these Powerbrake fronts, and the lack of brake cooling, and my mistakes in skipping cool down laps, the PB23 compound pads that I purchased with this set of calipers still have a ton of life! These are motorsports calipers so they are made with thicker-than-OEM pads, but still - many of these race weekends in 2016-17 were with two drivers. Amazing stopping power and pad life.

    OTHER SMALL UPGRADES

    There were a number of other little modifications we accomplished over the summer before our MSR-Houston event September 22, 2017. I will briefly cover those below - including the loss of the "daily driven track car" moniker!

    TT4 = NO MORE STREET CAR

    There is usually a tipping point you come to in a dual purpose car where it no longer makes sense to keep it street legal. Too many compromises that you have to make for street use that limit the track potential in TT-Number class - especially the aero. Driving a car with a rigid, low mounted splitter on the street is nerve wracking! I feel that our recent "beginnings of the move" to TT4 are already unleashing too many compromises that are just not appropriate for street use. While we kept our TT3 Mustang "street legal" for long time, at a certain point when it became more competitive, it no longer made sense. That's where we are on this 330... inevitable, with the TT-Number move looming just ahead.



    Last time when we added the Sparco Circuit II seat with the halo support the car was safer on track but became less safe for street use. Why? While this style seat really helps save your head/neck/back in a side impact, the halo portion blocks a some of your side vision. I mentioned it briefly then.

    In a race car you should have enough situational awareness for this small blind spot to not matter, but on the street where you have a lot more crazy people trying to kill you... not ideal. Swapping seats is a pain and we have so many more daily driver cars (including other E46 models) it didn't make sense to do that with this car, so its off of "street duty" for now.



    We also pulled the front seat belts and the Texas rear license plate came off. A fake Euro-style, vanity plate went in it's place (these embossed metal pieces look like real plates and cost $25-35 online). We were also never going to run the TT4 motor with catalytic convertors, which are dangerous to run with in long stints on track with a race motor, so we can avoid that limitation. And registering/inspecting/insuring the car costs money that I'd rather spend on race tires. I just sold the fresh set of Dunlop ZII street tires (to pay for race tires!), dropped the insurance, and decided to no longer "dual purpose" this car. #BecauseRacecar It still has roll up windows and the A/C might stick around a while longer, but those might both go away in the future as well. We will see.

    MORE BALLAST + M3 GAUGE CLUSTER SWAP + FUEL LEVEL FIX

    With the 6 points spent on air dam and splitter for TTD we had to add the 80 pounds of ballast back in the trunk, going from the 3205 lb number we have been running this season up to the 3285 lb number shown. We are so far under max power/torque it isn't even worth noting (but we do have it on our classing sheets and dyno printouts).



    Two 45 lb plates + one 25 lb plate are double secured to our weight bracket in the trunk. I lost 21 pounds over the summer (Atkins) so I had to add that for a total of 115 lbs of ballast now (the roll bar gobbled up about 60 pounds). We left with only 1/2 tank, to test fuel slosh, too.

    continued below

  9. #59
    Fair's Avatar
    Fair is offline Senior Member Supporting Vendor
    Join Date
    Oct 2003
    Location
    Dallas, Texas
    Posts
    3,634
    My Cars
    E36 M3, E36 LS1, E30 318
    continued from above



    Note that between our first race in Jan 2016 we have gone from a 54% front weight bias down to a much ideal 50.5% front bias now. We have been moving weight down and to the back every chance we get.

    A random failure of a stock gauge cluster in the silver 328 led to a musical chairs of E46 cluster swaps - my red 330 gave up the stock cluster and a leftover E46 M3 cluster made its way in. This isn't a 100% plug-in swap - there's a beeping alarm and "brake light" lit up ever since - but the fuel level, water temp, speedo and tach all seem to work perfectly. Don't know about the oil temp gauge? Bonus: the M3 has a 9000 rpm tach, which might come in handy for next year's motor!



    Also (not shown) Aaron pulled inspection covers for the fuel tank to see our dual fuel pump setup, which fuel cut at Hallett in right hand turns with 1/2 tank or less. He re-routed one of the crossover hoses to be able to to retest at MSR-H.

    CURRENT TTD POINTS BREAKDOWN

    Below is the list of modifications in this, the final iteration of this car for TTD class. TTC goes away in 2018 and rumor has it TTD will be sacked as well, both replaced by TT4/TT5. We won't see those new TT5 rules until its too late to build for next year, but very likely we would have to ballast up or power down for TT5.


    Ballasted up to our new TTD 3285 pound number with me in it, + 1/2 tank of fuel, + 5 lb buffer

    So we planned on running TTD at least one more time in 2017 before making the jump to TT4. Our E46 330 starts in TTE class and has 39 points to spend with "1 class UP jump" to TTD (+19 points for TTE and +20 points once into TTD). Here's the points breakdown:

    + Base classing of TTE* with 3285 lb min
    + 7 points for the BMW E46 330 "star" added to this car in the 2016 rules (*GRR!)
    + 10 points for Hoosier Racing Tire R7 compound
    + 1 point for 245mm tire size (+10mm from 235mm base class TTE tire)
    + 0 points for weight reduction (we were taking +6 for -80 pounds previously)
    + 1 point for cold air and/or hood venting (haven't vented yet)
    + 5 points for non-stock headers, cats, exhaust
    + 3 points for 2 way non-remote monotube coilovers (Motion Control Suspension TT2 model)
    + 2 points for non stock springs (Hyperco coilover springs)
    + 2 points for swaybars (Whiteline at both ends)
    + 2 points for non-BTM brakes (Powerbrake front 340x35mm 4 piston)
    + 3 points for add, replace, modify front fascia or air dam (5° variance from vertical) - New mod
    + 3 for add, replace, modify a single flat front splitter (up to 6" wider than body and up to 12" sticking out front) - New mod
    ================================================
    39 points (everything else we have done is an approved "free" mods)

    CUSTOM "REMOTE TUNE" - NO GAIN

    In an effort to squeeze as much out of the TTD setup before we go to the new motor next season, and to see if the BMWeditor software actually works, we asked for some help from a friend at another shop. He knows how to load a tune into these cars, and had a tune sent from a "remote tuner" who tunes BMWs all the time. We communicated the mods the car had (header, exhaust, no cats, no air pump, CAI) and the goals (road course use) and he had something that he felt would fit the bill. We did not have time to book a dyno - this happened suddenly, the day before we left for MSR-Houston.

    It took a little effort but our local buddy got the tune to load and actually start and run. I drove it around the block and it "felt better" but who knows? Maybe that was wishful thinking. I was just glad we didn't have the stock tune any longer! I knew we couldn't possibly go beyond the class limit of 244 whp from our 216 whp previous dyno, so we loaded the car up for the NASA weekend.



    A few days after this race weekend I went by True Street Motorsports (who does not tune BMWs directly, but has a dyno and tunes all of my GM and Ford V8 powered cars), where we made several pulls to see what the power numbers and air:fuel ratio looked like with the wide-band O2 they hook up during pulls. In the graph below we have overlaid the best "stock tune with headers + CAI" pull (in blue) with the best pull of the new "tuned" setup (in red). We made 3 pulls that day but they were nearly identical.



    As you can see it didn't change much at all. The "tuned" curve was within 2-3 hp of the old one everywhere, and was actually down 1 hp at peak. If it wasn't for the much worse Air:Fuel ratio I would have guessed that this car still had the stock tune loaded. In the upper end of the power band where it matters, the A:F went from 12.05:1 (rich) with the stock tune, down to 11.05:1 (VERY rich) with the new tune. So it went from bad to worse. Not dangerous, just far from ideal.

    I worked in the late 1990s in a shop where we did custom EFI tuning using a chassis dyno (and some street driving) with a wide band. I know what it takes to tune a car, and like I have said in the past, I feel that canned/email tunes or "remote tunes" are impossible to do properly without a lot of time on the tuner's end and someone with a dyno + a wide band at the car's end, so this "shot in the dark" tune went about as I expected.

    Now that we know what the hang up was on our end with BMWeditor (the BIN loader software), and we can see what happened between the stock tune and the new one, we can work with the tuning software directly, while on the dyno. If we can get the A:F closer to ~13.5:1 at WOT, that should unlock a few more horses. Running at 11:1 or 12:1 won't hurt anything, just not the way to make the most power on a Naturally Aspirated motor.

    NASA @ MSR-HOUSTON SEPT 21-23, 2017

    As I showed above, the new splitter still required all 12' feet of the 2-piece RaceRamps to load, but it goes in relatively easily. With the front tow hook it can be winched in, but I normally just drive it in and out.



    We loaded up the Thursday evening before the event, bringing along a second set of 17x10" Forgestars (ordered over the summer, powder coated gold) mounted with two "fresher" R7s and 2 new "sticker" R7s that I won earlier this year (the one day we finally had 5 in class, Saturday at Hallett). With no time for track testing before this event we went ahead and signed up for the Friday "test day". The plan was to run the old set of tires on the silver wheels (which had too many events on them) at the Friday test, try get the car and driver dialed in with the new front aero, then switch to the sticker/newer set for Saturday to run TT.

    FRIDAY - TEST DAY

    We towed down 5.5 hours from Dallas to Houston Friday morning, got to the track, found a spot to park and quickly unloaded the car. Ran over and paid the $75 for the afternoon test sessions and I was in my gear and on the track by 2:30 pm.



    Since I was rushed I didn't put the vid cam in the car, but ran the AiM SOLO for lap times. Right off the bat I was way off the lap record pace set in 2014, by one of my customers in a BRZ that used to run in TTD with MCS TT2 coilovers and Hoosier A6 tires. Not only did I have a poorly handling car at speed I was having trouble remembering this track in this direction.



    MSR-Houston has been on the NASA Texas schedule twice each year for a while. They alternate the direction for the January event (normally CW) and the September event (normally CCW). For various reasons we have missed the September NASA event here most years, as this is usually a busy month where we have other events going on that pull us away. After looking back at 12 years of running NASA events, I've only found one other instance where I ran this track in the CCW direction - back in January 2014 (when it was cold, where Hoosiers work much better). This might explain why the CCW record for TTD is fairly solid at a 1:48.5 - the MSR-H CCW event wasn't run that year during the traditionally hot "second" September event date. I ran that event in TT3 that year and it was COLD, but I put down a 1:41.4 lap which was the class record until it was reset in 2015 by a TT3 M3 with a giant front wing (which prompted a front wing ban from all TT1/2/3 production cars).



    So I was re-learning the track again in the 330 in hot weather on a pretty used up set of tires. But still, I knew we had a setup problem - the car was very loose in high speed corners, especially Turn 2 (the Carosel). I was entering this corner at about 85-90 mph, avoiding the curbs, but it would step the rear out badly at speed. It wasn't shocks or tires, it was mid-corner at the limit - I could enter the corner slower fine, but as I sped up the nose really planted and the rear stepped out. This was the "new front downforce" working like it should, just a little too well. With no rear wing to balance that new front downforce out it had an aero imbalance. Damn it.

    It was also very hot and humid - 95°F in the late afternoon sun - which didn't help things. Still, my lap times were getting "better" the longer I drove, as long as I kept my cornering speeds down in Turn 2. Very frustrating - I knew what the problem was, just couldn't fix it without pulling the entire splitter off. About 10 laps / 20 minutes into this session the coolant temps started to creep up. I took a cool down lap and they came back down, but as soon as I pushed it again they were spiking. No steam or water coming out that I could see. I shut off the engine, coasted around the track to pit in, and came into the paddock right as the session ended.

    Fuel pump check: The car started this session with a hair above 1/2 tank of fuel and after the 20 minutes on a course with a long right-hander it had no fuel starvation, got all the way down to 1/4 tank with zero issues. At least we can say with confidence now that the dual fuel pump upgrade does indeed work.

    Continued below

  10. #60
    Fair's Avatar
    Fair is offline Senior Member Supporting Vendor
    Join Date
    Oct 2003
    Location
    Dallas, Texas
    Posts
    3,634
    My Cars
    E36 M3, E36 LS1, E30 318
    continued from above

    When I got out of the car I could smell just a hint of coolant. Even though we have purged this coolant system of any traces of anti-freeze, and all we put in is distilled water and Motul "MoCool" additive, it seems like you never really get ALL of the old stuff out. I could hear just a small hiss of steam, so I popped the hood and it was coming from a tiny pinhole in the plastic coolant reservoir tank. Almost impossible to see, buried at the bottom of the engine bay.

    The thicker aftermarket radiator core was pushes the plastic reservoir a tiny bit closer to the engine, and with some uncontrolled radiator movement the tank started to rub into the power steering pulley - under heavy braking, I guess? The same exact thing happened at TWS last year, and way back in 2011 on my blue 330 with the same radiator setup.

    I was now on the clock - it was past 3:15 pm on Friday when I found the issue, and I needed a new reservoir, fast. Called our shop manager Brad and he started calling around - he found one at a WorldPac warehouse 32 miles north, in a rough part of Houston. They were supposed to close at 5:30 pm, so we quickly unhooked the trailer, hopped in the dually and raced north. We got there fighting the worst Houston 5 o'clock traffic I've ever seen at 5:12 pm, whew!



    Traffic was still VERY BAD. It was going to take nearly two hours to get back down to the track, and by then it would be pitch dark. We re-routed, picked up several gallons of distilled water, headed to the hotel, and decided to get to the track right before dawn and change out the tank (its a 5-15 minute fix, if you have light). At least we got to eat some good food in Pearland at an old favorite - Los Cucos, Tex Mex.

    SATURDAY - HPDE5 DAY 1

    We got to the track very early, and it was foggy and dark. The cooling system was cold so I started to get the old reservoir off. Its a series of quick disconnects for several coolant hoses and attachment at the radiator neck, 5 connections total.



    I was fighting with the new tank install when I had to run off to an instructor meeting at 7:20, then a TT meeting at 7:40. I had enough time after that to get the tank on, refill with distilled water, let the car idle and hopefully "burp" coolant. I then secured the radiator with a big mess of zip ties, and yes it looked janky. I would have swapped on the "gold" wheels, but time was too tight, so I ran the old set from practice. It was just the Saturday TT warm-up, and any times taken would only count for gridding in the 2nd TT session (which would then count for times/classes).



    I got to the grid, got strapped and ready with the 5 minute warning, engine warming up... then the coolant temps spiked - it had burped out another air pocket. Shut engine off, coasted back to the paddock. Popped the cap, refilled it again with more water (and one more time later that day) to get the system bled and filled. Back to grid, no more cooling problems. Then we waited for 30 minutes...


    Left: MSR-H just a few weeks earlier was under water. Right: Same section of track "dry"

    Turns out the Hurricane Harvey had flooded the track weeks earlier, and this led to electrical gremlins with the timing system during this event. The AMB timing loop wasn't working consistently. A crew of guys was frantically working to patch the timing loop, hoping there was a break. Both the Primary and Secondary loops were failing to register transponder pings. At one point they finally sent us out for the TT Warm Up, telling us it was fixed. The TT group was gridded randomly and I was stuck behind a lot of traffic when we went out, but I fought my way through and found lots of time on the old tires - according to my AiM lap timer. I was finally into the 1:50 range, inching closer to that "cold" TTD record for the CCW course. Was finding ways of driving around the aero imbalance, but it was still very limiting.

    I thought about pulling the entire splitter Saturday night, otherwise I might lose this class of 5 TTD cars with the aero imbalance issue. There were a couple of "dyno-reclassed" engine swapped, gutted race cars in TTD that I had never seen before. The track was still a bit moist from the morning fog/dew, so I came in after the traffic got really bad, not happy with my times but knowing that the sticker/new tire set would help and the fog would burn off before lunch. Sunday morning is always the "money session" anyway. Once back to the paddock Amy said the live timing system "...Race Hero didn't show any times for anyone". Hmm, that's odd, must be a communications problem? Got to grid for my HPDE1 student. And we waited for 45 minutes while they again furiously worked on the timing system again... So we didn't get any official times from the TT warm-up?



    This went on all morning - no functional timers, frantic work, sending out cars to test the loop, and yet no times. HPDE folks had no issues because they get no times anyway. W2W groups didn't have a qualifying session and instead gridded for races after lunch by season points, but they got to race (they had a gang of volunteers hand scoring every lap, showing which cars passed start/finish in what order). But we were assured the timers would be working after lunch, so I swapped onto the gold wheels and newer tires. Got to grid for the first afternoon TT session, another long wait. When they sent us out I found a lot of time in the afternoon heat, knocking on the door of the old record with some 1:49.0 laps. Got some good passes in, figured I'd place grid really well later in session 4, might sneak into 1st, and have some good video/data to crunch over night. Sunday morning I could get this track layout in my brain, see some faster times in the cooler weather...

    Wait, what? Once again the timers didn't work, and they were down for the rest of Saturday. TT was officially scrubbed, with no times, no results, no points, and no contingency for the day. Damn it, and we finally had 5 in class. The fastest "unknown" TTD car left broken on a flat bed and wouldn't be back for Sunday. So I might not have 5 in class tomorrow, but at least we'd have timers by then. They had a whole new AMB timing loop being brought in, after patching both the primary and secondary loops in the track AND moving the karting track's loop over with no luck - it wasn't for a lack of trying. They said they'd "work all night" on the timing system if they had to, get it fixed, no worries. We had surprisingly good Thai food for dinner, then went to see Kingsman 2. Turns out Pearland is actually pretty nice little town, just about 25 minutes from the track.

    SUNDAY - HPDE5 DAY 2

    If you aren't seeing the "HPDE 5" notes above, that's what we were calling the Untimed Time Trial group. Our luck did not improve - We never had functional no timers on Sunday, so the entire TT weekend was scrubbed for us. We could run if we wanted, but with no results. Really really disappointing to come this far and get no times. There was no back-up means of timing TT, either, we were just S.O.L. I never took a lap on Sunday - what was the point? I had already put a wasted session on a sticker set of tires for no results.



    I tried to stay positive and spent the day working with my HPDE1 student, then coached with two more: a DE3 guy in a S550 Mustang and a DE4 guy in a Corvette. My new wired helmet comm system worked great with all 3 guys, and we all saw some good driving and time improvements in the very hot weather. We loaded up the BMW that afternoon and after a lot of sweat and work, headed home.

    Its just a bitter ending to what became an extended test weekend. Our last TTD event in this car here was just not going to happen. The fuel pump test was successful, we have narrowed down the recurring coolant reservoir issue, and the front downforce test was proven, too - the splitter made way too much impact, and let me know that it would need a wing to balance this out, and quickly.

    WHAT'S NEXT?

    A few days after that event we brought the car to True Street for the dyno check, which I showed above, which just added further disappointment. We then measured the chassis for width (68.9" wide, minus mirrors) and immediately ordered a wing for use in TT4 (68.5" wide). AJ Hartman is making this carbon fiber element now and we will show the new wing instillation next time.



    The TT4 wing mount will be similar to the E46 M3 wing on the V8 car above (same width as the car, 8" above roof), but with some changes for possible "production" manufacture. I'd just use AJ's uprights but they are tailored for BMWCCA, much lower than NASA allows. We're gonna shoot max allowed width, max allowed height. The endplates will need to be smaller but otherwise pretty similar to the M3 setup.



    Before the next event we will trim the front splitter just a bit, to get all of our ducks in a row for TT4. We are signed up for NASA @ NOLA for Oct 27-29, where we will go down on Thursday to be able to run the Friday test day. We will probably step up to 275 R7 tires (max size allowed in TT4), yank all 115 pounds of rear ballast, and jump right into TT4 class - under powered and over weight. We can then work on dialing in the new wing's AoA to get some aero balance in high speed corners, which NOLA has in abundance. There's no prayer of winning TT4 in this car yet, but it will give us an idea of how the class is looking and give us some goals to shoot for in 2018.

    Thanks for reading!
    Terry Fair @ Vorshlag Motorsports

  11. #61
    Fair's Avatar
    Fair is offline Senior Member Supporting Vendor
    Join Date
    Oct 2003
    Location
    Dallas, Texas
    Posts
    3,634
    My Cars
    E36 M3, E36 LS1, E30 318
    Project update for November 10th, 2017: Last time we had a record FIVE PART forum thread update here - and that was only a month ago. And this time... well, its another FIVE part post, so you better grab a snack.



    As you can see above our TTD E46 has jumped up two classes to TT4, then we raced it with NASA at NOLA Motorsports Park - with somewhat shocking results. We will cover the latest round of mods (Big Wang!) that pushed this build out of TTD class (a class that is going away in 2018 ) and then chronicle the race NOLA race weekend at the end.



    We also need to catch up with work done to the 328i Track Rat dual purpose build we couldn't fit in last time (including 17x10" wheels RS4 tires, above left), and we have recently completed a huge round of repairs to the black 325 automatic we bought earlier this year (above right) - soon to be a Daily Driver for Amy so we can LS swap her Scion FR-S. So once again we have a lot to cover!

    FINAL MODS & DELIVERY OF 328i TRACK RAT

    We started building this 328i in 2016 "on spec" as a dual purpose street/track car, but heavily track focused. We tackled the suspension, brakes, roll bar, chassis reinforcement, and more. Last time we covered the many changes to the interior and safety bits that were upgraded.



    HARD MOTORSPORT FLARES ADDED

    We had planned on selling this car with a set of 17x8" Jongbloed 3-piece wheels and Hoosier race tires we had in the shop from another project. When our customer Jeremy saw the car he loved it, but liked the 17x10" Forgestar F14 wheels and flares on our red 330, so we ordered up another set of raw wheels and HARD Motorsport flares.



    This set of flares was specific to the E46 non-M sedan chassis. These were mocked up on the front fenders and marked on the paint to see where to trim the fender lips. The mounting holes for the bolt-on/rivet-on flares were also marked and drilled in both the flare and fender.



    There was a slight bit of trimming to perfect the fit. After the front fender lip was cut off (at the lower marked edge of where the flare touched the body) they were then riveted in place using the black aluminum rivets included in the kit.



    The rear is obviously a lot more work than the front, as these pictures show. We went over this on our red 330 but we took a few more pictures this time. The flares are mocked up and the top and bottom edges are marked, then the outer skin of the rear fender was cut off at the flare's lower edge. The inner structure of the rear fender was then pie cut and folded out 90° to meet the outer edge. These were then welded to the outer skin and the "flaps" were cut off.



    The inner structure was then seam welded to the outer fender skin and made waterproof with seam sealer. This is a significant amount of welding that should not be ignored. The structural integrity of the rear of the unibody relies on this outer skin to be welded to the inner skin - don't skip this step.



    The fender area was then primed and the flares were riveted on. As you can see the sedan uses some extra pieces that tie into the rear doors, but the structural changes for tire clearance are all done on the rear fender area (the door is not cut). We took the picture above right with these flares and a real E46 M3, and you can see they are nearly identical.

    UPGRADED WHEELS & TIRES

    Picking the wheels and tires for this dual purpose street/track car looked at three main variables: cost, grip and wear. The tire options for 17" wheels are less costly than 18" versions, but the width options run out above 255mm width. While we could probably have run an 18x10" wheel and the popular 285/30/18 size under these flares, the customer wanted the more cost effective 17" tire option for this set.



    In the 255/40/17 size there are many options to choose from, but for what this car needed to do (drive to and from the track and also put in a lot of quick laps), these two stood out: Bridgestone RE-71R and Hankook R-S4. The price of the RS-4 was a tick lower and it seems to wear better than the RE-71R, but look at the difference in tread width and section widths. The R-S4 is nearly 0.5" wider! Stretched out onto the 10" wide wheel the wider 9.4" tread width of the Hankook will be able to put more rubber on the ground and costs $130 less per set (at the time of this writing). The softer compound of the RE-71R might make up for this width deficit, but the wear would very likely be higher.



    The wheel choice was rather easy since we get most of our custom built wheels from Forgestar. We also work with D-Force on flow formed BMW wheels, and their 18x10" option is a nice setup, but he wanted 17" tires so we chose Forgestar. We also work with some other higher cost companies for custom wheel sizes but the price point wasn't right for this build. We ordered a set of 17x10" F14 wheels identical to what we used on our 330, requesting them in a "raw" finish to save time getting them built. One of our local vendors powder coated them with a flat textured black finish, which looks great clean or dirty. The RS-4 tires were mounted and balanced up and of course we got a wheel and tire weight.

    BELTS, HOSES, DRIVETRAIN MOUNTS, RADIATOR, FLUIDS, OIL PAN BAFFLE & OIL PUMP DRIVE

    In this section we will show the oiling system upgrades, cooling system changes, custom brake cooling, new belts/hoses, Vorshlag motor/trans mounts, new Motul fluids, plus some other small repairs and a few more little restoration jobs. That's a lot of work, and some of this was done before we sold the car and some completed after, but I'll go over these tasks quickly.



    A Mishimoto aluminum radiator was installed along with new E46 radiator hoses, heater hoses, and a water pump. The Mishimoto upgrade is cheap insurance that we do to any track E46. This removes any plastic from the radiator and adds system volume and heat shedding ability with the thicker aluminum core.



    A new internal seal and a fresh steering rack boot stopped one last power steering leak.



    As is usually the case the original hydraulic fluid filled motor mounts were toast, and one side had separated completely. This accelerates a lot of the hoses/radiator leaks on these cars - the unrestrained engine, flopping around the engine bay, yanking on all of the hoses.



    Our competition motor and trans mounts went in place, with Nylon motor and Red poly trans mounts being the preferred combination on this heavily track-centric car.



    A spare M54 oil pan was already on hand so it was cleaned in the ultrasonic tank at our engine shop, HorsePower-Research (HPR); we keep a spare pan around for these baffle installs because we do them so often. The engine on this 328 was then supported from above with a beam style engine bay stand, and the crossmember was dropped. Then the stock oil pan was removed.



    An oil pan baffle from VAC was ordered and fitted to the oil pan. There is always a bit of trimming, fiddling, then some TIG welding to install these. A very worthwhile upgrade for road course use - prevents long high-g corners from starving the oil pump pick-up in the pan.



    Another very worthwhile upgrade for track use is a beefier oil pump drive shaft. We picked the VAC unit and swapped that in place of the OEM bits, which had a loose nut on the shaft and was bound to come off. There are other brands and styles but regardless - upgrade the oil pump shaft on any track abused M54 to avoid complete oil pressure loss. Ask me how I know this!



    The OEM balancer is usually a cause for alarm for track use, but this one proved to be in perfect shape. No cracks in the rubber isolator ring and it had not "slipped" relative to the hub, so it was re-used (with the customer's consent).



    To finish off the maintenance a full change with Motul ester based synthetic oil, Wix oil filter, and Gates belts were installed.



    Early on in the build I decided to replace the exhaust with a Magnaflow stainless cat-back system. This system fit great except right at the dual tip opening in the rear bumper cover. That was trimmed to match the wider exhaust tips and now looks OEM.

    FRONT BRAKE COOLING

    On a road course you have to use the brakes, a lot, creating a lot of heat. To keep the rotors, calipers, pads and fluid in the proper operating range you should really think about positive pressure brake cooling. The OEM brake cooling from BMW is barely better than nothing, and the E46 non-M has poor brake cooling support from the aftermarket, so we set out to develop something for the E46 330 front brakes (which we have on the front of this 328i).



    For the prototype setup we made the backing plates and ducts at the hub from aluminum, hand cut and TIG welded together. If/when we make a production version it will be made from stainless steel and CNC laser cut, but for a one-off aluminum works fine. The backing plate is designed to push as much air inside the rotor face, to cool the hubs then be sucked through the vented rotor like an air pump. We went with a 3" oval opening, to keep almost 100% of the airflow inside the rotor face. The closeness of the backing plate to the rotor face is to help seal the hub area to the ducting, so air won't go around the rotor but instead through it.



    Once the backing plates were welded they were bolted in place and 3" high temp brake duct hose was attached to the oval inlets on the backing plates. These need to be fed from a high pressure zone at the front of the car, which we will show below.

    continued below

  12. #62
    Fair's Avatar
    Fair is offline Senior Member Supporting Vendor
    Join Date
    Oct 2003
    Location
    Dallas, Texas
    Posts
    3,634
    My Cars
    E36 M3, E36 LS1, E30 318
    continued from above

    We need to feed high pressure cooling air to the backing plates, and that air comes from the front of the car. Since the customer did not want to switch to the E46 M3 nose - which has better brake inlet options - we re-used the OEM inlets in the lower grill.



    Again, the OEM setup has some brake ducting, but it just dumps air into the inner fender. We wanted to keep the forward inlet sections that seal to the front nose but re-route into hoses that run along the front swaybar. Above you can see where a "bite" was taken out of the OEM outlet, which puts cooling area "near" the hub area. As the tire turns it cuts off that supply, so we needed a re-route ahead of that point.



    The smooth plastic rectangular duct work from the factory also incorporates some of the inner fender liner. These are actually very well made, but the original bits from this car were long smashed and/or missing. So a pair of new ducts was purchased from BMW. These molded plastic parts have rubber flaps at the front to better seal to the bumper cover's rectangular openings.



    About a third of the back sections of these new ducts were cut off, then some aluminum oval tubing sections were fabricated, shaped, and riveted into the rectangular ducts at the rear - pointing them away from the fender liner and tire.



    The pictures above show the modified front inlet duct work installed, and the diverted section that normally cools the alternator (which seems a bit silly) was blocked off to force all of the air into the brakes. The 3" high temp hose was slid over the rear...



    The hoses were secured with 3" worm gear clamps and the brake cooling was complete. Doesn't look impressive externally, since the front inlets are stock, but it definitely pushes some air through the rotors and keeps the brakes and front hubs cooler. This front duct work was so customized it is not likely that we will make production "inlet duct kit", but maybe some E46 owners will see what we did and make their own home brew versions.

    328i ALL WRAPPED UP!

    The Forgestar F14 17x10" wheels and tires + the HARD Motorsport flares really wake up the look of this car, and the added grip will definitely be felt on track. We got a final weight with all of the work completed and were pretty happy with the results.



    The before and after pictures say a lot there. This car is now 344 pounds lighter yet is still street legal, emissions complaint, has functional air conditioning and heat, lights and wipers, and all of the factory glass. The wheels are all 2" wider than stock, suspension is much firmer, brakes are bigger and cooled, oiling system upgraded, and tons of deferred maintenance has been completed.



    Jon cut a little vinyl per the customer's request and Brad got it all cleaned up. I'm happy with the finished results, as we took a rather plebeian 328i and turned it into a lighter, more nimble, better stopping track car that can still be street driven.



    The customer has since wrapped the roof (which hides the carbon delete panel fairly well), added the factory undertray bits, plus a few other upgrades. This 328i has already seen several weekends of track use and the owner loves it. He can drive to the track with cold air blowing and the windows rolled up, then get there and let 'er rip. This ended up with more of a dedicated track car interior than what we had on our 330, and made for more of a "dual purpose" build than even our red car as well (we've now stopped street driving our TT4 car).

    2003 325Ci COUPE AUTOMATIC

    Earlier in 2017 I picked up a "problem child" E46 coupe from a former customer who was just tired of dealing with maintenance issues. We used to be his shop of preference back in 2011-13, but when our shop moved from North to South Plano the distance just got too great and he stopped coming to us for service. He ended up getting the run around from a "normal repair shop", the type of place where they mark up the parts 500% and charge way too much for service work. Repairs bills with $800 starter replacements started wearing him down.



    That kind of repair bill terrorism sucks, and I felt bad for the guy. When this car was under our care we took good care of it, and even upgraded the stock wheels to 17x8.5" D-Force wheels, replaced the A-, B-, and C-pillar interior panels, and did all sorts of maintenance. We have since steered away from doing "basic maintenance work", because unless you are willing to rip people off its a tough business to make money in. Now we do more track prep, suspension, chassis, safety, and fabrication work - which still doesn't make any money, but at least it is fun!



    So back in the spring he called me and said he wanted to unload it. His kid had kind of driven the car hard and it wasn't nearly as pretty as it was when we last saw it, 3 years earlier. It ran very rough, had a bent wheel, and needed many repairs. I bought it and hauled to the shop to get it cleaned up and running better.



    Facebook just reminded me today that eight years ago I bought my first E46 (actually two on the same day). At this point I've stopped counting the E46 cars that have "followed me home", but they always leave our care in better shape then when we got them. That silver 328i above was transformed, and even Jack Daniels left cleaner and better running than before. Well this black 325 was barely running with a massive intake leak, plus that bent wheel. I figured this one would be an easy fix. Of course I was wrong!

    DISA VALVE UPGRADE + WHEEL REPAIR



    The M54 family of engines has a "dual tract" intake manifold, with a "DISA" valve after the throttle body. This valve switches between a long and even longer set of runners on the intake manifold. These valves are notorious for sticking and worse - falling apart and being ingested inside the engine. This one was literally falling apart, and luckily hadn't been eaten yet. It was leaking badly at the mount on the manifold, which is why it ran so poorly.



    We learned that the M54B30 DISA valve we had from another 330 motor doesn't fit the smaller 2.5L M54B25, so it was time to rebuild the original DISA unit in this car. Like always I ordered the repair/upgrade kit from German Auto Solutions (I am not a dealer nor do I have any affiliation with them), shown above. This replaces a bunch of janky plastic parts with stronger, machined parts made from better materials for about $75. These are the features right from their website:
    • The plastic flapper valve has been replaced with a black anodized & stress relieved 6061-T6 aluminum flapper valve that is twice as strong and many times less brittle than the stock part it replaces.
    • The plastic crank lever has been replaced with a black anodized 6061-T6 aluminum bell crank lever that is four times stronger than the stock part it replaces.
    • The flapper valve and lever lock together on a precision machined hex shaped taper & are screwed together, instead of just snapped together like the original design. Locking the parts together prevents any possible movement and wear between the two pieces, the #1 cause of failure in the stock design.
    • The parts are securely locked together by a custom, light weight, titanium pivot screw that's held captive from outside the housing. The titanium pivot screw also replaces the stock steel pin of the original design. Since the pin is part of the pivot screw, and the pivot screw is held captive from outside the DISA housing, there is no longer a possibility of a steel pin coming loose and getting sucked into the engine

    We do this upgrade on virtually all M54 cars we build to race or to street drive. For $75 in parts you can prevent catastrophic engine failure, and in this case make the car run 1000 times better. This should be on the list for ALL E46 CARS PURCHASED.



    These new parts + an upgraded Viton O-ring (also from GAS) were installed into the old DISA valve then it went back into the intake. And it ran smooth as glass! The wheel was repaired and looks as good as new, too. Still had some leaks to fix...

    LEAK FIXES + NEW BRAKES + NEW STOCK SUSPENSION

    I want to make this slushbox equipped E46 coupe into a nice, reliable, smooth riding commuter car for my wife. Her commute is pretty crappy and has a lot of stop and go traffic, so the automatic might be a nice change from her normal manually shifted cars. So to keep it simple we're NOT upgrading the brakes, suspension, or engine beyond new stock parts.



    This engine has the normal leaks and the first place we often look is the valve cover gasket. Sure enough this rubber gasket had turned into a brick, cracked, and was leaking badly.



    With a new gasket, spark plugs and some engine bay pressure washing once it was buttoned up the engine was now leaking much less. We're keeping an eye on the now clean engine looking for additional leaks to tackle, but for now its a whole lot better. Some vacuum lines were also replaced at the same time.



    The old battery was a massive lead acid unit, which was very old and was not holding a charge. This poor car sat at our shop for 2 months waiting for a break in the schedule and was driven out of the shop and back in every day, so that didn't help the battery's life. This new Bosch unit is the same size as the OEM battery and tips the scales at 47.2 pounds!



    The suspension was pretty tired, not necessarily from the miles (160K) but the age and use (it was 100% part of a daily driver grind). So new OEM replacement control arms, LCA bushings, inner and outer tie rods, swabar end links, top mounts and drivetrain mounts were ordered. The old ball joints and bushings on the control arms were hammered, but the new bits fix all of that. Normally I will always go to Powerflex 2-piece LCA bushings at the very least, but this time I went with stock. Should ride smooth like butter!



    The stock motor mounts (see old vs new, above left) and strut top mounts (also old vs new, above right) were both worn and "shrunken" over time. This is what happens to rubber after 13+ years - and we went back with stock bits on these parts as well. Rare for me, but we have ZERO delusions of this car ever seeing track use.



    The rear brakes looked fine but the front rotors and pads were done, so those got replaced with Centric Premium rotors and Centric branded ceramic "ultra-quiet" something-or-other pads.



    Brad pressure washed the aluminum chassis brace (which was covered in oil) and then wrapped up the front suspension repairs. This shot is without the plastic front undertray installed (its still intact on this car). We took the car home after this round of work and... the transmission started slipping badly after about 30 miles of driving. First automatic E46 I've ever bought and of course its bad! Since I have a low mileage GM E46 trans laying around, of course this car has the ZF automatic - which has outrageous rebuild prices ($2000-4000, ha!) I will talk about that issue and subsequent repairs next time.

    continued below

  13. #63
    Fair's Avatar
    Fair is offline Senior Member Supporting Vendor
    Join Date
    Oct 2003
    Location
    Dallas, Texas
    Posts
    3,634
    My Cars
    E36 M3, E36 LS1, E30 318
    continued from above

    INITIAL TT4 PREP TO E46 330

    You made it through the work on the silver 328 and the stock black 325 above, so now we finally get to talk about the red 330! Last time we covered a ton of work to the front of the car - new bumper beam, M3 bumper cover, inlet ducts, brake backing plates, splitter, air dam and tire walls. We took it to MSR-Houston and.... had a massive aero imbalance. All front df, no back aero, not hard to imagine, right? What would fix this aero imbalance - nothing less than a massive rear wing.



    We were out of points for TTD mods, thanks to the re-write of the base classing in 2016, otherwise we would have done this full aero build TWO YEARS AGO and been much faster this whole time. Since TTD goes away next year, we were way ahead of the season long 2017 regional TTD championship back in June, and since no TT cars got points at MSR-H due to timer issues, we had a lock on the regional TTD class championship. So we decided to test the waters in next year's class early - TT4.

    There were a few small repairs and updates needed but the bulk of this work was all about the rear wing.

    WINDSHIELD REPAIR

    We started out by replacing the front windshield, which had a massive crack in it on the passenger side, which was growing.



    Since we no longer had plans to ever street drive this car we could get the less costly, thinner glass windshield without the "Rain Sensor". $130 installed, no more crack, no more pitting, perfect.

    SECONDARY RADIATOR TOP BRACKETS

    The wobble on the top of the radiator on this 330 (which has allowed the coolant reservoir to rock back into the power steering pulley) was finally traced (by looking at some other E46 models) to some missing upper rubber bushings that were never on this car when we bought it. These screw down into the top of the stock radiator and keep it in place. The spots they would be are now where we have the pins mounted for the AeroCatch latches for the hood, so we cannot just add those rubber knobs back.



    So I asked Aaron to make these aluminum brackets (just inboard of the hood pins, above) that bolt to the radiator support and "capture" the trailing edge of the top of the Mishimoto and keep it from moving. Some rubber pads keep the aluminum bracket from wearing through the radiator - we'd see how this worked at NOLA. I brought a spare coolant reservoir with us just in case.

    BIG ASS WANG

    We had read the TT4 aero rules very carefully a few weeks earlier and had ordered an AJ Hartman Aero carbon fiber wing element to fit the limit of the class - which can be as wide as "the maximum width of the car" and placed "no more than 8 inches above the roof line".



    There are no other wing element or mounting limitations. We measured the stock bodied 2003 325Ci Coupe width at 69" at the rear fender lips (we have to ignore the side mirrors), then ordered the 14" chord wing at 68-1/2" wide, to have a bit of margin for measuring error. Now it was time to make uprights using the basic shape and height of the E46 Chainsaw Massacre build's wing.



    Ryan had fabricated the uprights for the M3 by hand, and it took a big chunk of time to make all of those interior cuts. This time I asked Aaron to make the set for my 330, and we worked with Jason to simplify the trunk mounting points and removed the extended lower bumper beam section. We moved the wing forward a hair but kept the same basic height. The first mock-up were made in fiber board, shown above.



    After I sketched what I wanted changed from the mock-up he was able to get that into CAD, make some CNC plasma cut uprights, and incorporated a slot-and-key feature I wanted with some load spreading mounting plates. These four slotted mounting plates self-jigged into the keys of the uprights to make fabrication easier and more repeatable.



    This worked perfectly and the mounting plates were tack welded to the uprights on the car. These were then removed and finish TIG welded on the bench, with a good bit of heat. The mounting holes were countersunk and flush mounted hardware was used to secure them to the trunk from the inside.



    This was all designed in up front but to verify legality we moved the wing to maximum Angle of Attack (AoA) before stall (12°) and using a level from the rear of the wing and an 8" tall box on the top of the roof, we were within the limit of the rules. We set the AoA to 6° based on some calculations and speculations as to the effective downforce of the front splitter. We could dial the rear wing to balance the front at the track soon.



    The wide angle lens makes this wing look much bigger than the car, but it is in fact 1/2" narrower than the stock fender lips, and well within the limits of the class. The end plates were direct copies of the somewhat subdued units from the V8 M3, and also well within the limits of TT4 class rules.

    WEIGHT SAVING INTERIOR UPGRADES

    Moving to TT4 means we would be massively overweight with the power we currently have (210 whp avg, or 216 whp peak) for TTD - hell, we were 30 whp down for TTD, but had no more points for upgrades in that class. Until we do something drastic we could at least ditch some weight. 115 pounds of ballast in the trunk was easy, but after that would start to get more difficult.



    I have been wanting to ditch the stock steering wheel and airbag for some time, and now that there's no more street use it is appropriate to upgrade this. The weights above aren't super high but removing an explosive device from in front of my face is always a win.



    For this car I chose a Sparco L360 (Ring) Steering Wheel, which has a black suede cover and comes in 330mm diameter. Sparco's hub adapters are hit or miss and for the E46 I prefer the MOMO 6-bolt Steering wheel hub adapter, part #2012. This allows any 6-bolt 70mm PCD steering wheel to bolt to the E46 steering column AND keep the horn. Even though it doesn't see street use, having a functional horn has kept my cars from being backed into on grid more than once. Keep the horn!



    There are airbags in each side door, so those two 1.6 pound "potential bombs" were also removed. I lost some pictures, including getting the 13.3 pound weights of the OEM door panels, with speakers. We were replacing the panels with low profile, thermoplastic formed racing door panels from HARD Motorsport (3.0 pounds each).



    Mounting these is done with rivnuts added to the door, then what look like 3D printed plastic stand-offs screwed into those threaded holes. Then the door panels is fitted a bit and bolted in place.



    Brad traced the custom mounting panels from the V8 M3 to make another set for the driver's door on this 330. This panel mounts the factory power mirror controls, so those can still work. This bolts in place of the little tweeter speaker.



    There is a mount for a pull strap which passes through a slot in the door panel. The passenger door kept the little speaker in place for now, but we might go back and make a blanking plate for that side later. We briefly thought about yanking ALL of the carpet and foam backing, which probably still adds 70 pounds to the car, but I decided to hold back - for now.

    FRONT AIR DAM TWEAKS

    So last time I pointed out that "anything can be called a canard" since the NASA ST/TT rules do not define what a canard is. So the "tire wall" we built last time, which absolutely does not create downforce, was called a canard... which isn't allowed in TT4. Instead of forcing the issue with a protest against myself at NOLA we looked at this a little harder, Jason and I read the air dam rules and figured we could easily make that taller here and cover up all of the tire wall extension at the somewhat incomplete fender flare. This would have less aero drag and be completely legal. This is what we call a "win-win".



    A small bracket was added at the base of the outer edges of the splitter and then a piece of plastic "race roll" was riveted in place, covering the tire wall and looking nothing like a canard. It's all covered up by a 100% legal air dam extension.



    I also asked Aaron to trace a line showing the "projected outline" of the legal M3 bumper cover, which the TT4 rules reference 2 times in the aero rule section. This way its easy to see where the 4" splitter extension was measured from.

    FINAL WEIGH-IN AND LOADING



    With 1/2 tank of fuel the car now sits at 2942 pounds (as shown above) and 3154 pounds with driver, gear and helmet. We had the car sitting at 3290 pounds with driver and the same fuel load for the previous NASA event (on a 3285 pound minimum), so the ballast removed from the trunk and the weight savings in the interior lost 136 pounds from our previous TTD setup. Still, we were VERY heavy for TT4 - minimum weight for our current power (210 whp avg) would be 2520 pounds with driver, which we could not hope to get to without MASSIVE amounts of cutting and carbon composites. This meant we were a staggering 634 pounds overweight for TT4 at the next event... not a good deficit to try to overcome. Of course we will be adding power and not trying to find 634 pounds of weight loss for our future TT4 build, so you can also say we were down 90 whp. I felt this deficit was so insurmountable that we'd be lucky to avoid LAST PLACE in class, and we had 5 signed up for NOLA.



    Wow, 634 pounds overweight is massive, and as we loaded up and my head hung pretty low. Jon cut some vinyl and replace the "D" letters with "4" numbers. The 2-piece ramps plus the flip down door on the trailer made loading pretty easy, just as long you approach the end of the ramp carefully. Its still easier to load than the TT3 Mustang, that's for sure!



    I'm sharing the TT4 classing sheet above with optimistic weight numbers of 2600 pounds - I could have put 2542 minimum, but inflated them a hair for "margin", hehe.... Who cares since the car is 600+ pounds heavier than that! Same goes for power - I claimed 215 whp avg, when its really 210 avg. Not that we will get dyno'd, but I always try to leave some margin for error on the stated numbers.



    We also kept the two sets of 17x10" wheels mounted with 245/40/17 Hoosier R7 tires we had leftover from previous events, even though we could have run a 275mm max width tire and more aggressive A7 compound for TT4. I didn't want to blow the $$ on new tires for one event when we were THIS OVERWEIGHT. I thought briefly about running a "slower class" like TTC (we'd still be hundreds of pounds heavy), but I really wanted to run a NASA event against the fastest TT4 cars in our area as-is. And for reasons that would later prove to be true, I feel that the TTC class cars are faster than their TT4 counter parts.

    continued below

  14. #64
    Fair's Avatar
    Fair is offline Senior Member Supporting Vendor
    Join Date
    Oct 2003
    Location
    Dallas, Texas
    Posts
    3,634
    My Cars
    E36 M3, E36 LS1, E30 318
    continued from above

    NASA @ NOLA, OCT 27-29, 2017

    We have not raced at NOLA Motorsports Park in 4 years, but we had a lot of fun the last time we ran with NASA here. We were eager to get back and Amy and I both planned to drive the 330 this weekend. It was SO MUCH FUN - we are both glad we went and vowed to make at least one NOLA event per year in the future!



    We completed this round of "TT4 prep" on Wednesday so we got on the road Thursday morning to make the 512 mile trek from north Dallas down to New Orleans to run at our final NASA weekend of 2017. We spent the entire day driving the 9-1/2 hours through Texas and Louisiana, got caught in some traffic around Baton Rouge, then rolled into NOLA right at dark. We unhooked the trailer, found a parts store to sell us DEF fluid for the diesel truck, went to the hotel, then found a local watering hole to get some good Cajun food.

    FRIDAY TEST-N-TUNE

    Friday was an absolutely beautiful Fall weather day in the deep south. Sunny, light breeze, 70-80°F all day, just perfect. We arrived on time for the 8:30 drivers meeting for the test event we signed up for, where we hoped to re-learn this track we have only raced at once back in 2013. I was startled to see that the TT3 track record we set on the 2.75 mile course 4 years ago still hasn't been toppled (1:50.525), but I figured it would surely fall this weekend (it didn't).



    The test day was run by the track itself and cost a whopping $250, which is relatively high for this area (our last test day at MSR-Houston cost $75), but they do put on a good show and the track had nearly every corner station manned. They separated the entrants into 3 groups: W2W Race cars, Advanced + Intermediate HPDE, and Beginner HPDE. Since we don't have a full cage in this car that meant I would go out in the Adv/Int HPDE group. There would be five sessions for each group during the day and I ended up running four of them. There was no riders, coaches, or instructors allowed in the cars, plus Amy could not take a session in my place - $250 per person per day. Bummer, but I would be able to ride along with Amy on Saturday for some coaching.



    We unloaded the BMW and set the tire pressures (27 psi cold) on the silver wheel set, which had the older scrubbed set of R7s mounted. We were planning to run this set Friday and switch to the gold wheels (fresher tires) for Sat-Sunday.

    It was good to do this test day, being that I hadn't driven this track in 4 years. It slowly came back to me and I was able to adjust my lines to work with this "momentum car" vs the more powerful setup of the Mustang. We stayed with our existing shock settings, and the 6° AoA wing setting felt damn near perfect. We adjusted tire pressures and got them all about 32-33 psi hot, with a 1 psi bias for the fronts. This course is CW so most of the corners are right handers, which meant the right side tires needed higher initial pressures when cold.



    There were some bumps that had formed since the last time I ran here which were noticeable in 3 corners: T5, T6, and T7 all have a pretty big dip in them - but good dampers make these non-issues. There's some "gator teeth" curbing that you drive over in a few spots (which you will hear in my in-car video), and some FIA inside curbing that you can drive over if you enter the corners at the right angle. There is also a concrete wall along the pit straight that you need to avoid (more on that below!) and some armco out near some corner stations that seem to be magnetic as well. Our group on Friday could pass on any of the 5 straight sections of track parallel to the pit straight.



    We figured out on this Friday test day that the M3 cluster's fuel gauge is "problematic". In my second session the car was fuel starving at "3/4 tank" gauge levels, which I knew was not right. So I went to the fuel pumps and... put nearly 3/4 of tank of fuel in the car? So it was reading high. After I filled it up it showed "Empty", WTF? So now I cannot trust the fuel gauge and we just started filling up after each session. We were using 3.0 gallons per 20 minute session, and I ran every lap of four sessions that day.



    The range of cars that show up in HPDE are all over the map, from commuters on street tires to Corvettes on Hoosiers to other TT racers testing. There were only about 20 cars in our Adv HPDE test group so traffic wasn't too bad and we quickly figured out that our little 330 was one of the faster cars running, so I started gridding as the first or second car out. The aero was really working. As my courage increased, so did my speeds through the high speed esses!

    The exit of T16 was pretty different from 4 years earlier, as they had paved a huge swath of run off area that used to be grass. They put a bunch of gator teeth in this area to discourage people from tracking out there but they told us that was all within track limits up to the concrete wall. One S2000 found his way into that wall Friday, destroying the whole right side of the car - but they beat the fenders out and he ran Saturday and Sunday anyway. I started using more and more gator teeth on track out and kept finding time... but it was a dangerous game to play.

    Lap times started in the 1:59 range and at the end of the day I was squeaking into the 1:57 range, still about 7 seconds slower than my old TT3 times, ugh. There weren't any published times all day Friday so I had no idea what any of my competition was running - just going off times from my AiM Solo, but those were pretty accurate 4 years ago (always within 0.1 sec of the AMB loop).



    We wrapped up the last session and swapped to the gold wheel set (above) to get the car ready for TT on Saturday. Some weather was supposed to move in and drop some wind/cold/rain overnight, but many of the Texas racers were camping out at the track in tents and trailers.



    After swapping tires we noticed that they were wearing extremely well. The last set that wore badly was an old set from our TTC Corvette, which had some shoulder wear that was worsened on the 330. Lots of tire klag inside the wheel but otherwise this set is good for more testing. After we had the car prepped for Saturday we went to our hotel, got cleaned up, then met my nephew and niece (who both live in N.O.) at a French restaurant for a great dinner - and I got to meet my grand nephew for the first time. Cute kid.

    SATURDAY - TT DAY 1

    We arrived at the track early for instructor's meeting, driver's meeting, and then a TT meeting. It rained pretty hard Friday night and was still wet and sprinkling on grid as we went out for our first TT session. We had a large number of TT cars but only about half of the folks made it to grid for the "TT Warm Up" session, and while I debated going I ended up driving the whole session. This "Warm-Up" would not count towards results (and being wet it wouldn't matter for times) but it would set the grid for the next session, so I went out on the bald R7s.



    Turns out that this wet session was a total blast and I had one of the quicker times of the session, running a 2:06 lap, which was about 9 seconds slower than my best times Friday in the dry but the quickest TT4 time (again, wet times don't mean much). What's weirder than entering a corner at 115+ mph flat on the floor in the dry is doing the same thing in the wet! One of the guys who I passed in this session said the rear wing was throwing up a rooster tail of water 40' in the air, "I couldn't see a damn thing - but you left me pretty fast anyway!" I ran the whole session and vacuumed the track a bit.

    That wet session put me 3rd on grid for the dry-ish "TT Session 1", and I assumed we would fall way down the grid throughout the day - but that never really happened. The weather for this session was COLD (temps started in the 45°F range), with high winds that would just cut through and made you shiver. Amy waited until after lunch to go out in the 330 with the HPDE 3/4 group ("Its too cold!") but I was on track for every TT session that day. Throughout the day the track was drying out except in a few stubborn corners, so times were dropping.



    During that first dry TT session, my times immediately dipped into the high 1:56s, and the third TT session I ran a 1:56.599. And while I was hoping to not finish last, somehow I as shown in 2nd place? I only knew one of the TT4 guys, Dysen Pham (S2000), who is always the fastest TT4 car at NASA Texas events - and he comes to NOLA a lot and is fast here. There were also three BMW M3s in class, including an E36 with an S54 swap that held the track record.

    In the 3rd session, "TT session 2", Dysen ran a 1:56.231 time but spun off track, hit some armco, broke his steering rack and had to come in on the flat bed. Since he did spin off track his times would be DSQ'd for that session. I ran a tick slower but the Race Hero readout and NASA results weren't posting right for the rest of the day - due to a wifi issue in the tower. That meant after the 2nd session we were completely in the dark. Frustrating, but I knew my AiM times at least. I figured one of the M3s would swoop in and destroy both of our times at some point.



    In the 4th and final TT session I was maybe sitting in 2nd or 3rd, wasn't really sure at that point, but I wanted to try to catch Dysen's time. I was pushing the car VERY hard, driving through the small puddles at the apexes of a few turns, using all the road and even a bit of curbing, but just couldn't find the time. The predictive lap timer showed a 1:55.8 lap more than once but I could never nail it down. I pushed hard for all 6 laps in this final Saturday session and on the VERY LAST LAP TT took all day I managed to get down to what I saw as a 1:56.3 lap on my AiM SOLO. I knew that wasn't faster than Dysen's best lap in his DSQ session - but what about his fastest lap from the previous one?

    continued below

  15. #65
    Fair's Avatar
    Fair is offline Senior Member Supporting Vendor
    Join Date
    Oct 2003
    Location
    Dallas, Texas
    Posts
    3,634
    My Cars
    E36 M3, E36 LS1, E30 318
    continued from above

    I came into the pits after that session exhausted - I had ridden with my HPDE1 student in 3 sessions, took him for a ride in a HPDE4 session, rode in one session with Amy, and drove every lap on all four of my TT sessions that day (9 sessions). The cold weather sapped our energy as well.



    We cleaned up, locked up but left the car out for the night with the windows up, then went to the awards banquet. They had some crazy good bar-b-q served up from a food truck outside and we went into the massive clubhouse to hear official results - which for once would be a total mystery. Did we finish 3rd? 2nd? Worse? Nobody knew.



    Once we got our food we went upstairs in the clubhouse for the awards. The race director was reading off the TT results and lap times, and apparently he was looking at the wrong column (2nd best times). He read them in the right finish order, so there was some confusion. When he read off Dysen as 2nd and me as first for TT4, I was in shock - mostly because the times he read off were not our best. Turns out the official times had us a tenth of a second apart, with my 1:56.347 lap taking the win out of 5 in class vs Dysen's 1:56.441. That meant 2 Hoosiers, woo! I was loving that luck, but figured Sunday would be the inevitable TT4 blood bath. The S2000 mafia that swarms these events is pretty industrious and they tend to fix all manner of issues quickly. There was also rumor of a V6 swapped S2000 showing up to run TT4 on Sunday that Dysen would co-drive.



    Amy drove two sessions that day and had a blast, and the car did great. We had battery issues on the vidcam but did get my best lap Saturday, just none of my Sunday laps. I also had some issues with the shifter, on both up and down-shifts, that ruined a few of my best laps. We will address both of these things next season.

    SUNDAY - TT DAY 2

    After sleeping for ten hours the night before (tired!) we woke up early, packed up the hotel room, and headed out Sunday morning to the track. The day started out a little warmer and the sun was out. More drivers and instructors meetings, then I worked on getting my student a check ride (he was more than ready for solo).



    It was still 47°F in our first session but the wind was down so it wasn't painfully cold. Most importantly the track was completely dry now and times started to drop. I was gridded P5 so I didn't have much traffic to deal with, which was a nice change. I was behind the two fast TTC cars and could keep them in sight. And while they both ultimately ran better times than TT4, you have to remember - TTC allows many things that TT4 does not, and these "dyno reclass" builds are going to be a thing of the past next year as TTC goes away. They have been fast all year, no doubt about it, but we will see if these TTC cars get faster - and by how much - next year when they all move to TT4 or TT5.



    That day I ran the first session hard and found a 1:55.975. Dysen's co-drive in the "S3200" (see above) never materialized - they had all sorts of issues on that car - but the owner did enter, ran at least one session, and made some 2:00 laps on street tires. Another M3 came in second but 3 of our entrants from Saturday dropped out, so we only had 3 cars in TT4 with times on the results sheet Sunday (so no Hoosier payouts).

    I went out in the next session looking to run a lower 1:55 lap (a predictive 1:55.8 time popped up earlier) and I started getting greedy with the exit "gators" on T16. I would take it wider and wider out of this last turn before the pit straight to try to gain a tenth, but it wasn't working. I ran a string of 1:56.0 laps then I took T16 exit a bit too wide and clipped the tire wall with the side mirror - BANG! Damn thing popped right off the door mount, hanging from the wires, but did zero damage elsewhere on the car. Whew! I got lucky. I held the dangling mirror in my hand for the next lap of shame and came in...



    Amy had seen and heard the whole thing from the bleachers at the exit of T16 - and she was none too pleased that I almost joined the "Wall of Champions" that had claimed other cars this weekend. I clipped the mirror wires, tossed the busted mirror into the trailer, then went right back out to take my nephew for a few laps in the next DE session. After that the car was all Amy's, and she did take another session that day, running her best lap of a 2:01.0 before we called it a day.



    By this point we had "found the time we were gonna find" and the ambient temps were climbing, while other TT cars slowed down or dropped out due to mechanical issues. One of the remaining TTC S2000s clipped another bit of armco and busted a wheel bearing. Another TTC S2000 broke their trans. Amy had dropped 10 seconds from her Saturday morning times and I found 2 seconds from my best Friday test time. My brush with the tire wall was enough of a warning to "not push my luck", plus we had an 8+ hour tow home and work the next day.



    We stuck around to watch the Blitz race group's last points race for the year, where our customer Jamie wrapped up first place the NASA Texas ST3 Championship - in his rookie year - which was pretty cool. He had "hit a gator" during the first race on Saturday and tore up the front end - but still finished the race. A bunch of us patched it up before the next race, which he went on to win and as well as the points race on Sunday (the car is at our shop now getting fixed up, better and prettier than before).



    We watched the Race Hero live timing app on our way back to Dallas and the 3rd and 4th TT sessions on Sunday didn't throw us any curve balls, so we won on Sunday as well. With only 3 in class there were not contingency payouts from Hoosier, but just winning the 2 tires Saturday was a nice change. The Sunday win had half the class out, but it was still another win - which meant we went 10 for 10 TT first place finishes this season (8 in TTD and 2 in TT4).

    THE GOOD AND BAD

    Overall this was a great race weekend but there were some exceptions. Running with the NASA Texas group for 11 years now I have gotten used to things being done a certain way. Here are some of the things that jumped out at us.

    The bad: There were a lot of incidents in various race groups, and some of the extractions took longer than they anticipated, which led to some delays. We had a lot of 20-30 minute delays sitting on grid after a 3 minute warning in TT. So the schedule was hit or miss. There was also some small level of disorganization - probably due the large number of Texas region folks that came to this "dual region" event. All of the W2W racers were jammed into two groups so they complained of traffic, but that's not my group. Long drive down on some fairly crappy roads, but it was all still well worth the trip.



    The good: The food at the banquet was excellent, and the clubhouse, track, and facilities were top notch. Everyone from NOLA was friendly and welcoming. There were autocrosses going on both days on parking lots within the facility, and some of the TT folks did some karting Saturday night, too. We had no traffic problems on track in TT this weekend, due to gridding so well Saturday and the car just being faster.



    Our 330 was sitting from 3rd to 6th on grid all weekend, which was a nice change. We beat the ST4 track record time but I was 1.2 sec off the TT4 record time, but we did outpace the car and driver that set that record earlier this year. Dysen had run a 1:51.2 in TTB last year but seemed to have slowed down in TT4 trim (just like I think how some of the other "letter class" cars might slow down in "number class" trim). Compared to the TT3 record our TT4 time was too far back, and the TTC record was smashed this weekend, but comparing to C isn't an apples-to-apples comparison. Jamie set the ST3 track record in his last lap of his last race, where he found a bunch of time in the high speed esses (his car has aero).



    The 330 definitely picked up a good bit of time with the added aero, which makes me think that next year we might be more competitive - with less weight, more tire and a lot more power. We shall see - I'm excited to to find out!

    WHAT'S NEXT?

    I've got a track test scheduled at MSR-Cresson for this car in about a week, so we'll see how much time the car picked up at our regular test track from our last set of laps there, again on the 245mm R7 tires. We have a major round of "power upgrades" scheduled for our winter break, and the preliminary 2018 NASA Texas Schedule is posted:
    • January 27-28 – Season Opener – MSR Houston
    • March 10-11 – March Madness – MSR Cresson
    • May 4-6 - NASA at COTA!
    • June 9-10 – Summer Shootout – Hallett
    • September 13-16 - NASA National Championship - COTA!
    • October 27-29 – Crossover event at NOLA Motorsports Park

    There might be another event or two added in the next month, too. Hopefully we will have completed the TT4 power mods by then, but there's not much of a break before 2018 season starts. We're back at it before you know it!

    Until next time,
    Terry Fair @ Vorshlag Motorsports

  16. #66
    Join Date
    Nov 2017
    Location
    PacNorWet
    Posts
    17
    My Cars
    2005 330ci
    Great read. Liking your detail builds.

    Bumping this to see what you have done over the winter ��

  17. #67
    Fair's Avatar
    Fair is offline Senior Member Supporting Vendor
    Join Date
    Oct 2003
    Location
    Dallas, Texas
    Posts
    3,634
    My Cars
    E36 M3, E36 LS1, E30 318
    Project update for October 15th, 2018: Somehow 11 months zoomed by without an update to this E46 BMW development thread. I kept meaning to post something, but things were moving pretty fast this year, and lots of things kept me from writing this until now. Some rules changes enacted because of our latest modifications ruined our 2018 TT4 plans for our red 330.



    So far 2018 has been a busy and tough year, for me and the business, but some long term plans appear to be heading towards the goals we set. We bought land, built a brand new shop, moved the business in a short period. I also bought a new for development + NASA TT (the 2018 Mustang GT, shown above), but also bought some more E46 chassis as well. New equipment at the new shop gives us some more capabilities, and we had some staff changes.



    My red 330 "Fireball" coupe (above) went through some cosmetic changes over the 2017 winter. This car won the NASA Texas Regional TTD championship for 2017 (by a huge margin), and we had moved to TT4 late in the season. While paint work was underway last winter, a big batch of rules changes came down that made all of our TT4 prep work illegal. Since I have to change up my personal cars regularly, to be able to develop new parts, the red 330 was sold this past Spring. I already miss that car...


    Left: Widebody/carbon door/carbon roof E46 coupe I bought (V8 build). Right: My slick top 2001 330Ci (SE46 build)

    Do not fret - we have a half dozen new E46 chassis coming in for various work, and some of those will be complete race cars we build for future customers. Long ago this forum thread outgrew our initial TTD E46 build (Jack Daniels) and since then we have shown various E46 BMWs that we have built, worked on, or raced. Some new E46s have been purchased this year, including the widebody E46 coupe shown above left, which already has carbon doors + roof and a big set of flares on it already. We have some nasty plans for that, plus other plans fpr the slick top white 330 Coupe, and possibly a Z4 (which has E46 bones) as well.

    TEST DAY AT MSR-CRESSON, NOVEMBER 18, 2017



    Let's pick up where the red 330 left off, 3 weeks after the wins at NOLA in late October 2017. The car was working well so on a cold and WINDY Saturday member day, Amy and I took the car to MSR. We had just swapped out the OEM mirrors for some cheap E36 M3 style side mirrors, to replace the one I busted at NOLA (read about that work below). That was the only change from the last round of work.



    Event pics: https://vorshlag.smugmug.com/Racing-...n-Nov-18-2017/

    My hope was to reset our best lap in this car on the 1.7 mile MSR-C CCW course. I had ran a best of a 1:23.789 back in March at the NASA event, in TTD trim, with zero aero. That day had nearly perfect conditions, and I had two days / 8 sessions to set that best lap of the weekend (and set the TTD record). We hadn't run at MSR since March, and never here with the TT4 aero. This is a track that normally responds well to aero downforce so I had high hopes.



    I went out early and had a relatively clear track. But it was very windy - and I think that was what was upsetting the car in some corners, badly. There were head winds, tail winds, but mostly cross winds. This made the car a real bear to drive and it felt like the "full tilt aero" wasn't helping me that day. Unpredictable, changed through the corners, etc. Bitterly cold with the winds, too.



    I went out in the first session and drove 11 laps, but only ran a best of a 1:24.079. Track temps were good, I wasn't fighting traffic, had no excuses other than the cross winds. The tires were fairly fresh, and I felt like I pushed the car to the limits, but I was just a hair slower than the March times. With the high winds Aero was a detriment that day. Other folks in race cars said the same thing that day. I watched my video and didn't see any major mistakes, just wasn't that fast.


    The inside front tire is off the ground here - and there's a lot of bodyroll

    There might have been some impact on loading of the chassis from downforce, it just wasn't consistent on each corner, because of wind direction. As you can see above, the inside front tire above was off the ground in Big Bend, possibly due to DF loads. If we had stuck with this car much longer we would need to increase spring rates a good bit. We saw similar amounts of "chassis compression" at NOLA as well, right after adding the aero. Adding wings and splitters usually requires spring rates to go up by 25-50% or more - with dedicated track testing trying new spring rates.



    Amy went out in the next session in the 330. I kind of hogged the car for many NASA events this year, and she didn't even make any laps in it at NOLA. As a "team" entry she could have, but we were focusing hard on securing a 100% win record for the year and resetting all of the TTD track records for the 2017 season - which we did. She more than deserved some track time today, and I wasn't sure if there was much more in the car with me driving.

    She went out and ran a 1:29.070 after driving for 13 laps. She had fun, but was further off my pace than usual. She hasn't driven a car with real aero since 2015, and the windy conditions gave her fits. It usually only takes a single coaching session with her to get her times within 1-2 seconds of me, or closer. With only 1 session under her belt, she was happy with her times.



    At this point I was super frustrated with my times. The wind wasn't letting up and was going to be there all day. A customer and friend, Scottish Joe, was there with his 2017 Corvette C7 Grand Sport. I hadn't driven his C7 here since August 2016, where I ran a 1:21.89 lap on the OEM MPSS tires. On this day he was on some 300 treadwear Continental street tires, so I suspected it would be slower than the Michelins it came with stock. Joe asked me to go out and set a lap to benchmark by, so Amy hopped in and we went out for 5 laps.



    The extra horsepower this LT1 V8 produces was downright addictive. Just horsing around I put in a best lap of 1:22.322. Sure, it was a hair slower than when I ran it a year earlier on better tires. This car was 1.7 seconds faster than my 330 race car with aero, in stock form and on not ideal street tires, with a passenger. And it was just super easy to do. Horsepower just makes every car better.



    Going faster in a bone stock LT1 Corvette that weighed 500 pounds more, on street tires, made me much less enthusiastic about this M54 powered BMW. As it turned out, this was the last time I ever drove this 330 on track. Its a little sad to end my time with a car on windy, cold test day that didn't pan out like I had hoped.

    2003 325Ci COUPE AUTOMATIC - ROUND 2 OF REPAIRS

    Let's skip over to one of the least impressive E46 cars we have in the fleet - our black 325Ci Daily Driver automatic that my wife has been driving for the last year.



    In the last post we showed a lot of suspension, gasket, wheel, battery, and DISA valve repairs on this car. Shortly after getting it back on the road the transmission started slipping. This car has the ZF automatic - which has outrageous rebuild prices ($4000!), which was more than the car was worth. What to do? There were some Check Engine Light (CEL) codes but we couldn't read them with our OBDII scanner.

    NEW FLUID AND TRANS FILTER

    Step one was to try the easy fix - fresh transmission fluid and a transmission filter. Sometimes a bunch of funky fluid and a clogged filter will cause the trans to shift funny.



    Brad dropped the pan and drained the fluid. Looked like old fluid, maybe original. Pulled off the older filter and rounded up a new one.



    The transmission pan was cleaned, a fresh gasket went on, and the new filter installed. A case of Motul ATF VI synthetic fluid was added, the car started and the fluid level was checked. Time for a test drive.



    Still slipping, badly. Hmm, not good. CEL was back, and again we couldn't read them. This isn't really our area of expertise, so we took the car to a friends BMW repair shop nearby. Michael from Eurauto hooked up to his fancy BMW code checking computer. Code 049 and 053 above had to do with the transmission.

    After talking to Michael and another BMW repair shop owner, it was time for a transmission replacement. The rebuild costs were sky high - I even called a friend with an Eagle Transmission franchise. There was no affordable way to rebuild this ZF automatic. Repairs that cost more than the car is worth - this is the ugly part of German cars ownership sometimes...

    USED TRANSMISSION INSTALL

    I started calling around and a correct E46 ZF auto pullout was found from a friend who owned a BMW repair shop. I horse traded some parts for this used trans, shown below. In hindsight maybe we should have done a little more work and converted this car to the 5-speed manual, but such is life...



    We cleaned that up (pressure washed), swapped over a wiring harness from our car's trans (that was busted on this unit), and the torque converter as well (our car's looked to be in better shape). Here are the technician notes from MyShopAssist on this work:

    MSA: R&R Transmission - Technician: Aaron - Time: 7.23 hours
    Filter Swap + R&R Transmission - 11/6/2017

    -Change fluid and filter in original trans
    -No change, still throwing codes and slipping
    -M12-1.75 x 75MM hardware needed (stripped/stuck), Qty:2
    -Chase M12x1.75 tapped holes in block
    -Power wash replacement pullout trans
    -Repair loom on P/N safety switch/gear indicator on pullout trans
    -Swap existing convertor into pullout transmission
    -Install new transmission mounts
    -Snug oil pan bolts (small leak present)
    -Rear main seal dry, do not R&R
    -Add new filter, pan gasket, fill with fluid, test drive



    Of course nothing is ever easy. Some knuklehead had buggered two holes in the block - probably the shop that did the $800 starter replacement for the previous owner. Since there was still a known oil leak (small), I asked Aaron to check the rear main seal and replace it, if that's where the oil leak was coming from. We had already changed all of the leaky top end engine gaskets in the last round of work. As you can see from his MyShopAssist notes above the rear main was dry - so its gotta be the oil pan gasket. The leak isn't huge, just annoying.



    Yet another new trans filter and another case of Motul ATF fluid went into this used transmission.



    A new driveshaft bushing (guibo) was installed when the driveshaft went on, and Aaron wrapped up this trans swap. The under tray was cleaned up and reinstalled. Fingers were crossed and I took it for another test drive - which was better, but not 100% better. It still throws some codes but the trans is functional. As long as you don't abuse it, it won't slip. For now.

    This is why I hate doing "junkyard swaps" with used parts - its the same work as putting in a new part, but sometimes the replacement used part is not 100% right. This is part of the fun of owning older German cars...

    continued below

  18. #68
    Fair's Avatar
    Fair is offline Senior Member Supporting Vendor
    Join Date
    Oct 2003
    Location
    Dallas, Texas
    Posts
    3,634
    My Cars
    E36 M3, E36 LS1, E30 318
    continued from above

    HEADLIGHT POLISH, INTERIOR AND EXTERIOR CLEAN UP

    Since the E46 was driving better, I went ahead and asked Brad a couple of days later to do a few clean-up tasks, to make this car look a little nicer. He spent about 3 hours to knock out the following.



    The headlights looked great, the leather was conditioned inside, carpets were vacuumed and the car was washed. Amy has been driving the car for the last 11 months. The transmission works, but there are still some other issues with it. It drives fine, and gets her to and from work, which for now is good enough. But we have more work to tackle...

    SMALL INTERIOR UPDATES

    One of my least favorite things on E46 BMWs are the factory cup holders. They suck, and are made for itty bitty cups, or small European soda cans. After time the spring clips that hold the dual cup holder insert into the center console wear out, and the spring loaded tabs inside the cup holders that gently squeeze the tiny little cans wear out. So if you have a teenie tiny can in there, corner hard enough, the can flies out. Or the whole cupholder assembly pops out of the center console, along with whatever was in there. Both situations are irritating.



    This car had a very worn out set of cup holders, and they kept falling out when cornering with a drink in place. Not cool. so I ordered a new OEM setup and popped them in place. But it was still pretty much worthless unless you had an 8 oz can or small drink cup.



    But to hold American size cups - like this Yeti-ish insulated stainless cup - we needed something bigger.



    This "Swigzy" cup holder "extender" works great. The bottom section can fit into the tiny E46 cup holder openings, then you can rotate the upper section and these ribs extend out and lock it into place. The upper portion can hold a giant cup - or your wallet,phone, etc. Very handy.

    ONE MORE POTHOLE, FOR GOOD MEASURE!

    A few weeks into daily driving Amy ran over a massive pothole and bruised a tire and bent another wheel. It was really a big "heave" in a concrete seam she ran over, but luckily the rest of the new suspension took the hit like a champ.



    I ordered two new tires (245/40/17 Firestone Firehawk 200 TW) and had that wheel straightened and refinished.



    These tires work really well, and in fact some endurance road racers have started using these for competition events. The Firestones were cost effective, ride nicely, and have great grip. The new stock suspension parts have made this into a very nice riding, decently handling little coupe.

    Dilemma - so the 2nd ZF auto trans is slowly dying, and you have to baby it to keep it from slipping. The CELs won't go away because they are tied to the slipping trans. this car also has a lingering "ground problem" in the lighting circuit, so the headlights/tail lights/brake lights are all dim. Gotta chase that bad ground. I have too much time invested in this for a slow, slipping trans, CEL lit car we can't drive at night because of the lights.


    PERFECT SEASON + POST SEASON PREP ON RED 330Ci



    Like I stated in the intro, we won the TTD class for 2017 with this car, scoring a perfect 800 points (with drops) for the class. We won every NASA event and even an SCCA Club Trial in this car this year. For NASA we set the TTD track record at MSR-C (both days), set new TTD track records for both the CW and CCW course at Hallett, set the record at TWS (both days), we went to MSR-Houston but it was a wash out (after the track was flooded during Hurricane Harvey), and then - since we had the TTD season wrapped up - we switched to TT4 for the last NASA Texas event of the year at NOLA (and won both days). We won TTD class by the largest TT class win, 645 points, and never lost a single event. It was a perfect season!



    What I had planned over the winter for this car was fairly monumental... I wanted to make this car a real TT4 car, built to the limit of the power-to-weight rules, max aero, go to a wider tire, and more.

    We were already deep into a radical stroker M54 engine build, had planned a custom "average power" tune with a stand alone EFI system to keep the car in TT4. I got wheels and tires to upgrade to 275/40/17 Hoosiers. Found a dry sump oiling system for an S54, which we could retrofit to the M54. And of course started on a complete re-spray of the car using the same Hellrot Red.

    The reality is that TT4 rules changed enough to prevent almost all of this for happening. Once much of our car was made illegal for TT4 we "pushed" on some of this work, other than the re-paint. Let's cover some of this...

    TT4 CLASS RULES CHANGES

    The "nail in the coffin" to further TT4 prep on this 330 was the significant rules changes that were made to ST4/TT4 at the very end of 2017, after only 1 season of this class being in existence. We will cover what changed, and how it affected our car.



    Apparently seeing our car's aero in TT4 prompted some changes to: wing endplate rules, splitter measuring rules, wing placement rules, and more. This was "not what they intended" when they wrote the limited aero rules for TT4. Even if we were deemed legal for the NOLA event, they told us that none of this would be legal for 2018.




    We only did what anyone building to the limit of a class would do - built to the extent of the rules. Can we help it if the rules didn't describe what was desired? It's not like we exploited loopholes or poorly written rules. We maximized the splitter, endplates, and wing placement for what was written. They didn't like that. So right away, none of our aero would be legal for 2018. It would all have to be redone, from scratch. After ONE RACE! I was less than thrilled.




    The other rule change that caught us out was the "standardized tire measuring tools" introduced for 2018 - a bit of a radical move that caught out a lot of racers. No longer would the tire size stamped on the sidewall matter - you would have to measure your mounted wheel and tires with some standard tire checking tools...

    This was done to reign in some tire makers that produced sizes that were wider than the numbers indicated, and to prevent racers from "stretching" a tire on a wider wheel to get more tread on the ground. If you have followed other builds we have done over the years, you might know that I am NOT a fan of skinny tires, but these rules changes were made to "keep costs low" and to prevent racers from using wider tires. The TTD build was always difficult for me, just having to use a 245mm marked tire...



    Of course for both our TTC Corvette and the TTD E46 builds we had done BOTH of those things to exploit tire rules: we picked the widest 245mm tire Hoosier makes (the 245/40/17 R7) and put them on 17x10" wheels for this TTD build. And we had just gotten a second set of 17x10" wheels made for the 2018 season, to have a set as "scrubs" and the "stickers" ready for when we needed more performance.

    I had planned on stepping up to 275mm tires for 2018, which on paper are "legal" for TT4 - but there's no way to mount them and fit within the class limit 282mm wheel checking tool (I bought a complete set of these tools late in 2017 to figure this out - too late). So I've got sticker 275s that I bought, and a 2nd set of 17x10 wheels for them now. Yay.



    So now we had built a car for a class that no longer existed - at least not with any of the mods legal for 2017 done to it. The reasoning was to allow the "Letter" classes to be gone for good in 2017, so the "new for 2017" ST4/TT4 classes needed to line up better with the new for 2018 classes ST5/TT5 as well as and 2019's ST6/TT6 classes.

    I get why they made the changes, it just didn't make me very happy to prep for a class late in 2017 and have exactly ONE RACE in this class before major changes came down the pipe. To be TT4 legal we would have to completely remake the end plates, radically alter the wing's fore-aft placement (brand new uprights), the front splitter would have to be completely remade and get much smaller and we would have to get new wheels to make even the 245s legal, forget about the 275mms I bought.

    This car was already WAY down on power for TT4 in 2017 (we were even down for TTD), and without a radical M54 engine build I'd still be down on power for 2018 PLUS we would have to make all new aero that would make less downforce. And no additional tire over TTD, and in fact less tire with narrower wheels I'd have to buy. So we would have to spend a lot of time and money to go slower. I already had the car at the painter's while all of these rules changes were coming down, very late in 2017, and I was unsure of what to do...

    ABORTED M54 AND S54 BUILDS

    I had hoped that my partners at the engine shop I am a part of would be more excited about developing BMW M54 or S54 engines - after initially being on board with these plans, I had rounded up heads and engine cores for development work, a complete dry sump oiling system, bought some rods to test with, paid for a test crank to check maximum stroke, paid for some tooling, etc.



    There is untapped potential there in the aluminum block M54 (215 hp stock) market. A few overpriced, underwhelming options existed for rebuilding an M54, but most folks just tossed them in the scrap pile and put in junkyard pullouts when they had a problem. We had a test crank made with a different stroke on each cylinder, then a forged aftermarket rod and piston we ordered that we tested in each bore. We had a pretty remarkable stroker combination that we were on the trail of... problem as it was going to be expensive. And the M54 intake, cams, valves, and ports all needed major upgrades to keep up with the added displacement. And the factory EFI was likely unable to support the programming. It was quickly turning into a very pricey unicorn kind of build. Would anyone else ever buy one? All of the development costs were on me.



    So I rounded up an S54, above. These have a heavier iron block but the block is taller, so we could add even more displacement. The S54 cylinder head can support more power (333 hp stock), but it would still need porting, valves, cams, and more. I got the dry sump setup for the S54, and we had lofty goals in mind. But my partners were much more interested in working on LS engines, late model Hemi, Viper V10s and Ford V8s. Can't really blame them, though. There is SO much more potential in any of those pushrod V8 engines than any BMW anything... dollar for dollar we could make a LOT more power with an LS V8 than an expensive, high compression, high revving BMW inline 6.

    With TT4 now out of sight for my car for 2018, I scrapped both the M54 and S54 stroker engine projects for now.

    NEW PAINT FOR 2018 SEASON

    After the November track test I was not "feeling it", and 2018 was looking like we might be further off the pace with the revised TT4 class rules, but at least the car would look good!



    I always intended for this car to look good - to represent Vorshlag well - but we had thrown a lot of changes at the body in 2017. We now had a raw carbon hood, 4 black flares, a bare aluminum splitter, a raw carbon sunroof, unpainted E46 M3 nose, black plastic race roll air dam and tire fairings, and raw carbon wing with bare aluminum endplates and uprights. It was time to get everything painted or coated.



    I found these E36 M3 style side mirrors that fit an E46, purchased those. The plan was to replace the OEM units after I had popped off the driver's mirror when I touched the wall at NOLA. Bonus: the two mirrors dropped 3.4 pounds from the stock power mirrors, and they produce considerably less drag.



    The new mirrors worked out well, but the eBay quality showed when it came to mounting. A bit of work was needed to install them (one of the mounting holes wasn't there), and of course we lost the remote power mirror adjustment. One of the front lower control arms was knocking again, so a Lemforder replacement was ordered and installed, too.



    We were not expecting the major aero/rules changes, so the car was already torn apart and being painted when the rules changes came down very late in 2017. Normally we'd try to make the late January 2018 event that kicks off the NASA Texas calendar each year, but with the new rules making all of our aero work illegal for TT4, I told Heritage Collision to not hurry the paint work.



    When I picked the car up in early February 2018 the paint made the car look AMAZING in every way. I was still unsure of what to do with the car, but at this point I had to do something since we had invested so much into it at this point. TT4 was out, and a build for TT1/2/3 would take even more radical aero and likely (if I was smart) an LS V8 swap.



    While I was deciding what to do with the 330, I had the guys clean up the tubular bumper beam/splitter strut mount and shoot it with silver paint, then reinstall that.

    continued below

  19. #69
    Fair's Avatar
    Fair is offline Senior Member Supporting Vendor
    Join Date
    Oct 2003
    Location
    Dallas, Texas
    Posts
    3,634
    My Cars
    E36 M3, E36 LS1, E30 318
    continued from above



    We had the entire front splitter powder coated in semi-gloss black. Much stronger than paint so they don't look like hammered crap after every event's worth of tire klag and bug hits on the leading edges.



    By this point I knew this car was looking very good, and I had Jon make me a "FOR SALE" graphic for the windshield. I figured I'd take it to some event soon and somebody would see it and maybe want to buy it? My intuition has been wrong before, but I figured it couldn't hurt.



    The endplates were already painted and the wing uprights and splitter were already powder coated when the rules changes were announced, so to change them now would cost not only the additional labor to re-make them but I would lose out on the powder coating and painting costs as well.



    We even had Heritage paint the raw carbon fiber wing, and with the painted aluminum endplates and black uprights the back of the car was looking just as good as the front.

    CLEANED UP AND PICTURES TAKEN

    By now I knew the car was looking pretty good, and selling this would help pay for the new car I just bought and the building that was under construction...



    At this point we left the decals on the panels that weren't painted - the doors and fenders. Everything else got painted in matching Hellrot Red - the nose, hood, mirrors, sunroof panel, wing, endplates, and flares.



    I was wondering if someone would buy this as a dedicated HPDE car that they could maybe drive a little on the street (the aero is the main factor here). I knew from previous builds that keeping the A/C, roll up windows, lights/signals, and some of the interior wasn't hurting us as far as potential buyers were concerned.



    Seeing this was making me have second thoughts... the paint popped, the interior looked great, but I kept saying to myself - how does a super clean dual-purpose car help us further the business? I couldn't find a class that it fit into without major changes and compromises. I was stuck.



    The interior cleaned up nicely, as you can see. The front carpets were vacuumed, the seats spiffed up, and it all looked great.



    Painting carbon wings body color is kind of a new thing, and after seeing what it looked like on our car, it's my new thing! Tired of seeing raw carbon blister or get cloudy from UV damage? Painting the carbon cures all of that.



    After a couple of days of waxing, cleaning, polishing, and even detailing the engine bay, Brad took the time to shoot some really good pics of the car. I was thinking of where to list it for sale at this point. Bring a Trailer? eBay? HPDE Facebook groups?

    SURPRISE WALK-IN SALE + FINAL CUSTOMER TWEAKS

    One of our customers, who had an exotic car in our shop for some custom work, saw the freshly painted and detailed 330 in the Spring of 2018. He asked how much I'd take for the car, and I threw out and number, and he said "Done".



    Of course it is never that easy, and we ended up doing a bit of custom work for him to complete the sale. On the interior he asked for new A-pillar coverings, as the originals had fallen apart and we tossed them a while ago. And with the headliner out, the interior light (above the rear view mirror) was held on with zip ties. So we made this aluminum bracket to finish that off, and keep the lights functional.



    Due to some variables out of my control, our "Daily Driven Track Car" here wasn't driven on the road after we did the custom header/exhaust. So it had no cat, until now. A Magnaflow high flow metal matrix catalyst was added.



    The buyer was no fan of the gold 17x10" wheels, so we swapped on the silver set with identical specs and R7 tires. I still have the gold 17x10" wheels for sale...



    He asked us to remove all of the decals except for the number/letter board on the doors, which we did. Then Brad waxed the rest of the panels where the decals were removed. It looked a little naked, but I have to admit it looked really clean with the all red body now...



    The owner sent a buddy down to pick up the car with a U-haul trailer, and after loading it a couple of times, then flipping it backwards, we were able to fit it onto this short trailer. I loaned them some padded Mac's Tie Downs for the wheels to secure it and off the car went. It has since been seen blasting around COTA, and last I heard - since he wanted more power - an S54 swap was underway. Sounds like fun!

    FROM ZERO TO HERO - 2 YEARS WITH THE 330Ci

    If you remember back we bought this car in 2015, and it was kind of a hood rat car. It had every window tinted with at least one layer of tint. It had a salvage title and all sorts of little problems that are associated with that, which we fixed. We put it together and tested a number of different things for this chassis, and it competed well in NASA TTD competition in 2016 and again 2017, winning regional titles both years.



    We tested three distinctly different suspensions (PSS9, PSS9 with custom springs, MCS RR2 with real springs), but kept the 17x10" wheel/245mm Hoosier R7 tires on each iteration, giving us some good data. Other than some of our very first races in NASA in 2016, it won every time out and usually set the track record for the class. We competed with this car in 13 race weekends, including 11 with NASA and 2 with SCCA Club Trials.



    We weren't quite doing the MSR-Cresson 1.7 testing in stages like we do now with our other builds (like my S550 Mustang and our FR-S), as we didn't get a "baseline stock" time on the OEM suspension and didn't go back to that track after every round of mods. But we did make some headway with the lap times, dropping almost 4 seconds there starting with the PSS9 setup to the MCS RR2 setup, on the same tires. Not bad. And there was time left with the aero setup - just didn't get to run it here with good conditions.

    Lap Times at MSR-C 1.7 CCW
    • 1:27.604 - NASA at MSR-C, March 12, 2016
    • 1:24.566 - SCCA Club Trials at MSR 1.7 CW, May 7, 2017
    • 1:23.789 - NASA at MSR-C, March 11-12, 2017




    The attitude of the car changed a lot from the earliest events (above left) to the later MCS setup (above right), before we even got into aero. I'm more than a little disappointed that we had to endure a sudden point penalty for this chassis right as we got underway, as we could have run full aero in TTD class before the * was added to this chassis - and that would have made the 2016-17 TTD seasons a LOT more fun. Still, for what the class allowed, I'm happy with the results and some of those TTD records will stand forever, as the class has been ended at the end of the 2018 season.

    UPCOMING WIDEBODY E46 BUILD

    In early November 2017 a buddy called and said he knew of a widebody E46 coupe for sale. It supposedly had a full Flossman body kit installed, like the one shown below. It also had ultra-light carbon doors, a carbon roof panel, and came with an E46 M3 rear subframe. This is what this body kit looks like, when done right:


    This is NOT the car I purchased, but rather a good example of what this body kit looks like on an E46 Coupe

    That could hold some serious tire. So I went to go see it. It was buried in a storage unit under a mountain of parts. That made it hard to see all of the details, but the price seemed appropriate for what it had. I could tell the front nose needed a lot of work, and the floor had been modified for a side exhaust (not my favorite mod), but it looked like it was all there.



    Once I had picked up the rolling chassis I could see it had some work that needed to be re-done. Super tall tires from a 5 series were rubbing the "undertray" (which we will cut off and replace with a splitter), so it was hard to steer. But it does have the real carbon doors, and some good bodywork on the flare install. Probably going to have to swap in the floor from a donor car to fix the side exhaust stuff, oh well.



    Yes, it looks very ugly in its natural multi-color paint right now, and sits up like a 4x4, but I have a vision! The carbon roof panel wasn't installed completely and needed some help to go on all the way, but this post is running long so I will show that work next time. Everyone else at Vorshlag thinks I am crazy for buying this one, but my plan is simple: perform an LS swap, add MCS coilovers, 315 mm Hoosiers, cage it, add some aero, and put this one up for sale when its wrapping up.

    WHAT'S NEXT?

    Its sad to see the "Fireball" 330 go, but with the TT4 rules changes and other new projects we have underway already we didn't have a place to race it - and the new owner is enjoying the hell out of it.



    As I am wrapping up this post, we might just have two more E46 Coupe chassis I am doing a deal for. So we should be starting a Spec E46 build with one of those two -or- the slick top white 330Ci chassis I already have. One of two new 330s (the running/driving silver one) could provide a major solution for our black 325Ci daily driver, to. I will continue to show all of our E46 related builds and repairs in this thread. Look for a new post soon!

    Thanks for reading,
    Terry Fair @ Vorshlag Motorsports

  20. #70
    Join Date
    Nov 2017
    Location
    PacNorWet
    Posts
    17
    My Cars
    2005 330ci
    Wow, great work. Sorry to hear about the rule change in TT4

    I too am building my 330ci for SpecE46. Waiting for your next project in that class

  21. #71
    Fair's Avatar
    Fair is offline Senior Member Supporting Vendor
    Join Date
    Oct 2003
    Location
    Dallas, Texas
    Posts
    3,634
    My Cars
    E36 M3, E36 LS1, E30 318
    Project update for April 11th, 2019: Its been about 7 months since my last post in this E46 build thread, but we have finally started a new E46 build - just not any of the ones alluded to on the end of my last post. We have started a project with literally the worst of the 5 "potential" E46 chassis that I own. This new project kicked off last night using this black 2002 330Ci automatic rolling chassis, below.


    Look at this cream puff! Who wouldn't want to make a race car from THIS?

    In this post we will show the first steps of this endurance road race build. Everyone at Vorshlag is working on this E46 after-hours, and all employees who work on and chip in for consumables and some parts will get to race in it. More of a team building exercise than a "we will conquer the world!" type of build. We will keep a sharp eye on the budget and consumables, and share what we learn along the way. We have built several customer endurance race cars before and want to apply what we have learned without any outside interference, other than the class rules. We want to run it primarily with WRL, but also NASA TREC, ChampCar, maybe SCCA Time Trials, and more.

    TEAM ENDURANCE BUILD - WE TRIED THIS BEFORE?

    We have been planning a shop endurance road race car build for years. I bought this clean, running and driving silver 1999 328i Sedan in 2015 with the intention of doing a "team" endurance road race build, with employees working on it after hours. Well, they worked on it once and the plan went kaput.



    The timing just wasn't right - some of our key employees at the time were not on board at the start, and other's lost interest soon after. Only a couple of people kicked in any money or volunteered any time on it (and luckily they still work here). After a while the car just sat, so we abandoned the "team" idea for this 328 chassis and my employees got their money back.



    Eventually I spent money and Vorshlag shop time to finish this into a dual purpose street/track car, built to be sold "on spec". A customer saw it and bought it before we had completely finished it, then had us upgrade a few things like the HARD Motorsport flares, 17x10" wheels, and some other bits he saw on our red 330 that he liked.



    Turned out nice, but not exactly what we had in mind initially - which was a fully caged, dedicated race car, built to the limit of a class, that everyone at Vorshlag could grab a seat in and road race in an endurance series.



    In an ideal world I would foot the bill and just finance a "team" car that my employees could all drive, but "ideally" I would have been born a millionaire and having to "make a profit" wouldn't be a concern! The dollars and cents for a small business like mine just doesn't work out that way. We also have a backlog of customer race car builds, so I cannot take away from our finite amount of 8am-5pm shop labor time to work on "fun cars" for the employees to use - especially ones that are not new product development mules (like our shop S550 and 86, below).



    Theoretically all of my shop-financed "test mule" builds (like my two current ones) should make the company money - with new products we develop and test with them. And for the most part, every test mule shop car we have ever built (other than my white C4) has earned their keep - making the company more than they cost to build, with new parts we can make and sell. Re-selling "other people's parts" (OPP) doesn't make real margins anymore, and building race cars simply on "time + materials" is a good way to go out of business.



    I have to be very careful on these shop builds to not overspend, over-prep, or otherwise make them un-sellable when we are done with them. All of this massively restricts their class competitiveness - every single time. This isn't meant to be an excuse, just the reality of selling our shop test cars at the end of their time here. Full on, purpose built-for-one-class, gutted road race cars are VERY hard to sell.



    My white TTC C4 is a perfect example of that - built it for a class that disappeared, which had a weird set of prep rules, and it took 18 months and I lost money trying to find the right buyer. I easily flushed $30K in billable hours down the toilet on that one. Ouch.

    Again, I'm not a millionaire and cannot afford to build money-losing personal race cars, especially ones that generate ZERO new products (we don't make a damned thing for C4 Corvettes). At least this endurance build doesn't HAVE to "show a profit", since the labor is volunteer and a good chunk of the costs will be shared by 6 people here at Vorshlag.



    So how many new products can we make on yet another E46 build? Well there are actually a number of things I have have thought of Vorshlag making, using some new tools and capabilities we have now - new parts and theories to test - and we will share all of that along the way. BMW made 4 million E46 chassis over this model run, so we won't likely run out of customers for this car any time soon. These are only secondary concerns on this build, unlike our normal "test mule" cars.

    TEAM VORSHLAG E46 ENDURANCE BUILD - PART DEUX

    I bought this hot mess of a 330Ci chassis a few months ago, which I agreed to take it as part of a package deal with another 330Ci (Silver) I bought and a caged Z4 chassis that I sold. This black car had a clear title but had been stripped of everything of value - M54B30 engine, trans (automatic), brake calipers and rotors, front bumper cover, driver's seat, lots of brackets and doo-dads all over the car. To most people, it was worth little more than scrap metal. I reluctantly dragged it to my property and left it outside...



    Andy at Clownshoe (who sold this chassis to me) told me to not build this car into anything like a SpecE46 race car, because it would need too many parts (which he had already picked clean). I took it off his hands for about $100 extra in this multi-car swap, mostly because he wanted the space and I had extra land to store it on at the new shop, outside with the other "potentials". It was a rolling chassis with 3 flat tires, nothing more, and soon forgotten.



    It was a Texas car so it has zero rust, but there is a poorly repaired dent in the left rear quarter panel, no sunroof, and a busted side window - so the remaining interior was already trashed from the elements. The hood and LF fender were already destroyed in a weird accident, which involved gravity, a steep ramp and an immovable object. Again, I didn't care as I have TONS of leftover E46 body parts. The red hood was installed here a few months ago, which was leftover from my red TTD 330Ci (which got a carbon fiber hood). I have several sets of cheap, new E46 coupe front fenders I bought years ago for E36 steel flare jobs so I will donate one of those - and an aftermarket E46 M3 bumper cover.



    After talking about a team build with everyone at Vorshlag for a number of weeks earlier this year, we seemed to all have a better attitude about it. The time seemed right. So we looked at various donor chassis and drivetrain options: NB or NC Miata, S197 Mustang, BMW E36 or E46, SN95 or Fox Mustang, C5 Corvette. We evan found a caged RX8 chassis we could have bought. In the end, I offered up this E46 chassis to the team plus a lot of leftover E46 parts for free, which pushed this car to the front of the pack. We started a shared spread sheet, then entered a bunch of costs and numbers. Talked about it at our group lunches for a couple of weeks...



    On April 10th, 2019 we officially kicked off this build with a "demo day" on the black 330 chassis, after work. Pizza was ordered, beer was chilled, and the car was rolled into the shop for an initial weigh in. Started the night at 2045 pounds as a rolling chassis. It was previously missing: steering column, driver's seat, one door window, brake rotors and calipers, front nose, headlights, and the 72 pound sunroof cassette.



    Everyone in town this week included me, Tim (above left), Evan (above right), Jason (below), and Amy, all worked on it with supervision by Erik from HPR. We took turns working on removing the interior bits inside the cabin, inside the trunk, and some remaining parts underhood.



    We made sure to carefully remove anything we might want to keep, re-use, or resell. I weighed everything that we had not weighed in an E46 build before, especially anything that might go back into this car. The giant HVAC box is a challenge to remove - it is bolted in from the firewall side, behind a couple of plastic panels. The entire dash has to be removed to pull it out, from the cabin side. Not an easily serviced part - thanks BMW! We will replace it with a lightweight motorsports heater core + blower motor, with a metal firewall panel in place of the giant hole there.



    The dash pad took some time to extract, but it came out cleanly, as did the dash bar structure behind it. We will likely re-use part of the dash pad, with all of the HVAC ducting removed. And we may or may not use the dash bar (if we do it will be incorporated into the cage). One thing I am insisting on is a clean, professional looking car, inside and out. A complete dash, even just the shell, makes a huge difference in how the interior looks - as well as reduces glare for the driver. We all want a good looking car - no "born to lose" jankiness that rolled out of the junkyard (even if this was a $100 scrap chassis and is being built affordably).



    The interior bits and extraneous wiring FILLED the dumpster I hauled the Dumpster over next to the shop door with the tractor, to make loading the funky interior bits easy. #TractorTherapy



    Engine bay was cleared out, but there wasn't much in there to begin with. I donated an entire E46 M3 rear subframe, one of my 210mm E46 M3 differentials (LSD 3.62 geared), some leftover prototype E46 long tube headers, and a couple of Magnaflow 3" mufflers leftover from a job we didn't need them for.



    I've also got a set of 17x10" wheels from the red car, this gold set I used exactly ONCE. The buyer of the red 330 car wanted the silver wheels, and these only fit a non-M E46 with flares - so they haven't been easy to sell. We will likely use another set of HARD Motorsport flares, since we have installed those several times and know the tricks. Price is right, too.



    At the end of about 3 hours of work we had the car 376 pounds lighter, with the carpet, rear seats, passenger seat, and the chassis wiring removed. We will likely NOT use any of the old BMW wiring, but I kept the harness for spare plugs and such we might need on other builds. The 1669 pound rolling chassis still has the driver's side door glass, window motors, both doors to gut, and some rear shelf bits to remove. Lots to go back in, of course. We need to pick the drivetrain, but knowing me it will likely be a rotary, with turbos. #ThisIsaBlatentLie

    WHAT'S NEXT?

    Just wanted to fire up this thread with a quick E46 project update, and I will follow up here after our work nights, especially when we finish something significant - like a cage, or brakes, or a new part we are testing. We will try to get this car up and going quickly, to get it on track for some initial testing, hopefully getting to a WRL event before the end of the year? Look for more build pics, weights, and drivetrain pics in the coming weeks. I will also post more frequently to the newly created "E46 Track Cars" Facebook page, if you are interested in these cars - join there.

    Thanks for reading,
    Terry Fair @ Vorshlag Motorsports

  22. #72
    Fair's Avatar
    Fair is offline Senior Member Supporting Vendor
    Join Date
    Oct 2003
    Location
    Dallas, Texas
    Posts
    3,634
    My Cars
    E36 M3, E36 LS1, E30 318
    Project update for July 29th, 2019: Its been more than 3 months since my last post here - 2 months of that was due to an outage with our forum. A server change forced an update to vBulletn, which forced a server upgrade and move, then we had weeks of DNS name change server issues. Finally, in late July we got our forum back up and I'm catching up on project posts. We have had many of our weekly employee team volunteer work nights on the Vorshlag Team endurance E46 build, so I will catch us up to current time in this post.

    FLOOR PANEL PREP FOR CAGE INSTALL

    We already removed all of the carpets, dash, door panels and other useless interior bits in the first week of work back in April 2019.



    What we were left with inside was a LOT of floor pan sheet metal covered in this adhesive sound deadening material, which I will refer to henceforth as "tar paper". Its really more complex than that, but tar paper is easier to write. We would fight getting this heavy, sticky, brittle crap out of the BMW for weeks, employing a number of removal techniques. Some here have even called it the Tar Paper Wars. One technique worked better than others...

    DRY ICE SLURRY METHOD on EVO X

    We did a cage job back in early 2018 on this EVO X, which had a welded 4-point roll bar we had to cut out and got a proper 6 point roll cage installed in it's place. This car still had all of the tar paper installed, which we had to remove since the entire interior and cage would later be painted grey.



    The method we used to remove this tar paper was suggested by one of our fab guys at the time, Aaron, who had used it successfully on Japanese cars before. The idea is the dry ice gets the adhesive holding the tar paper to the sheet metal so cold that the adhesive breaks loose, and then the tar paper comes off in whole sheets! I wanted to see this witchcraft in person, so we gave it a go on the EVO.



    With a 5 gallon bucket filled with crushed dry ice, isopropyl alcohol was added to make a chunky slurry that looked like a witches caldron. This slurry was carefully poured onto the top of the tar paper (the flat portions), then was allowed to sit and chill a bit, then light percussion with a hammer or scraper was used...



    It was like magic. This stuff just popped out in whole sheets! I never would have believed it, but damn, the results were real. In this EVO. This one time...

    DRY ICE SLURRY METHOD on BMW?

    We had high hopes and bought two 8 pound blocks of dry ice and a butt load of isopropyl alcohol to try this again on our E46 BMW's floors.



    At first we tried a twist - putting the dry ice + alcohol slurry into a black trash bag, that could let us re-use the stuff in several sections, as well as the vertical paper applied at the front firewall, transmission tunnel, and back seat shelf around the fuel tank.



    Well we gave up quickly on the trash bag, as it did not work at all. We went to straight dry ice + alcohol applied directly to the tar paper, as we did on the EVO. Problem was it was not working well on this car. Not at all.



    We tried this method again another work night, with two more blocks of ice and more alcohol. And more "percussive" persuasion. After many hours over two work nights, $100 worth of dry ice and alcohol, we barely had the passenger and driver seat flat floor sections done, and it looks like a 12 year old's patchy beard. This just did not work on this BMW, maybe due to more advanced age or possibly different tar/adhesive materials the Germans used? I give this a solid FAIL rating.



    I can NOT recommend this method to be used on a BMW. Not to mention that the alcohol poured out of the many plugged drain holes in the floor and trashed my new polished & coated concrete floors. I was less than happy about this - the alcohol/dry ice method is now banned in my shop.

    "GIVE ME SOME HEAT" METHOD

    We were still fighting this battle weeks later, and on the 3rd work night attempt to remove the tar paper, I insisted on trying my old proven method that we have used on dozens of BMWs in the past - a heat gun + scraper.



    This worked so much better on this car. With heat applied to a small section of tar paper for a number of seconds, a 1.5" wide putty knife was used as a scraper, and this stuff peeled right off. Not in entire sheets like on the EVO, but in manageable chunks and in a timely manner.



    The work went much faster than the dry ice, and no hammering was involved, just gentle scraping. It was like peeling fondant frosting off a wedding cake... came off in long chunks, after the heat nuked the adhesive.



    The video above shows this heat technique used on some vertical sections of the transmission tunnel - which would be nearly impossible to do with dry ice, even if it even worked. Like all methods, this still leaves an adhesive residue behind, which we cleaned up on other work nights.



    Tim tried a number of adhesive removers, from Acetone, to Goof Off Pro Strength, Brake Parts Cleaner, and finally Mineral Spirits/Paint Thinner. The Goof Off worked well enough, but its $15/gallon. The cheaper $7/gallon Mineral Spirits / Paint Thinner worked the best - just apply liberally to a blue shop paper towel, wipe it onto the adhesive, use some elbow grease, and the brown stuff comes off. Sometimes it took some work with a red ScotchBrite pad soaked in the same stuff as well.



    I wouldn't call this adhesive removal step "easy" by any stretch of the imagination - its not a "spray on / wipe off" kind of effort. You gotta get in there, use some pressure, and a lot of heavy duty paper towels and a little ScotchBrite to get it off. Just takes time.



    And sure, we could have used some power tools and abrasive discs or wire wheels, but that would have made a giant mess and we would have to prime the floors to prevent them from rusting before the interior is painted (after the cage is installed). I have heard from others that blasting or sanding this stuff only turns it into a fine mist of tar, which re-applies itself to the floorpan and other areas. As well as all over you and your shop. This heated peel + paint thinner method keeps the stock paint/primer clean and intact on the inside. We will just remove the paint near the "mounting feet" of the roll cage.

    MORE WEIGHT REMOVAL

    During some of the April and May work nights, while some of the crew was working on Tar Paper Removal, the rest of us worked on removing dead weight from the chassis. We would much rather overshoot our final weight goals on the light side and ballast up, than have to go back in chasing weight later, after the cage is installed. We also have 5-7 people on any given work night and we cannot all be working on the same area.



    Pulling the doors off allowed two of us to work while 3+ people were inside the car peeling tar paper and cutting/cleaning. One of the heaviest single assemblies on a BMW are the doors. These hold the side glass, an electric power window motor + tracks, and high strength steel side impact "crash beams". It is also one of the easiest places to lose weight on a road race car that is getting a roll cage.



    After removing the side glass, Evan used the plasma cutter to remove the bulk of the steel inner structure. Then I used the cut off wheel on a die grinder to trim out the hard to reach bits, as well as carefully cut out the side impact structure. This structure is tack welded into places we cannot reach, so it was sliced off at the ends, carefully avoiding damage to the outer door skin. Then the adhesive strip along the middle of the door was sliced with a putty knife and the crash structure peeled away.



    I left the front structure in place for the side mirror mounts, and some of the inner structure around the perimeter (to give the door some structure) as well as near the door latch and hinge mounts. This will allow us to still open and close the doors. The final weight was still 29.0 pounds per side, which makes the 8 pound carbon doors on our widebody E46 look that much more attractive. I didn't get a before weight (doh!) on a stock E46 coupe door, but I will make a point to before the next update.



    The front and rear glass were removed by a local windshield guy for $50 - he came by one weekend and used some specialized tooling to get these out cleanly. We can re-use the double thick safety glass front windshield (28.2 pounds) but we will replace the 18.9 pound tempered rear glass with Lexan.



    There are two "cavities" at the back of the engine bay, made with some sheet metal structures, that seal two the underside of the hood of a BMW E46. These are made to house the brake booster + master cylinder + main power circuits/relays on one side and the ABS system (or sometimes a battery on diesels) on the other side. The bits inside can be switched left to right for different markets, depending on which side the steering wheel is on.



    Well we plan on re-wiring the whole car, and the ABS pump and computer will not be in the OEM locations, so we can get rid of the sheet metal structure on both sides. A few minutes with a Saws-All took care of the bulk of the work.



    The rest was removed more carefully with a cut off wheel and even a spot weld cutter. The structure shown here on the left (driver's) side of the engine bay was more completely removed, as it makes room for the exhaust on the engine we have planned.



    You can see initial work on the "spot weld removal" above at left. The additional structure these pieces provide is negligible when you have a caged race car. Also, about 80% of the the "rear deck" structure (which the back seat uprights connect to) was removed, which was a little over 12 pound when we weighed it. Some classes don't let you remove that type of structure, but all the classes we plan to run will.

    POWER WASH CHASSIS

    This was a good time to stop and power wash the chassis, while it still could be rolled outside. On one of the work nights (during the middle of the "tar paper wars" above) we rolled the E46 outside and pressure washed everything.



    Under hood, inside the cabin and trunk, exterior - all the things.



    As you can see below, this is with some of the "rear seat" deck structure is removed.



    So much nicer working on a car that has the stinky interior removed, grease and other nasty "road funk" washed out.

    MUSHROOMED STRUT TOWER REPAIRS

    Something we commonly see on E30, E36 and E46 BMWs is the front strut towers - which are supposed to be flat - get worn over time to have a curved "mushroom" headed shape.



    This happens due to a somewhat thin sheet metal used to make the stamping for the strut tower plus the smaller, softer aluminum strut top mount that transfers load into the tower. If you hit enough big potholes over time, to the point of bottoming the suspension, the larger diameter strut tower will deform around the smaller strut top mount. The 3 studs from the top mount will also "splay outwards" like above. The two towers in this car were badly deformed...



    The fix is rather low tech - I like using a piece of 2x6" lumber a a 3 pound sledge hammer to flatten the upper portion back into shape. Light rapping downward with this flat edge, walking around and pressing laterally next to around the inner ring. I fixed both towers in about 45 minutes, then we could install a camber plate on that side (during suspension and wheel mockups, which I will show next time).



    This video clearly shows the technique on flattening the towers. Of course the front struts need to be out of the car to do this, and there are some tips to keep the towers from deforming again in the video.

    WHAT'S NEXT?

    We have a lot more work we have done over the last 3 months of weekly work nights to cover, but this update is getting long so I am going to save that for next time.



    We have researched, ordered and fitted some big flares, which will work with a wide tire package. We also developed a custom big brake kit (which will test on this car), that fits inside 17" diameter wheels. And of course the engine and transmission have been picked. Yep, swapping in a Mazda Miata 1.6L with a super charger! #ThisIsAnotherLie



    The air filter will be mounted as shown above, if that gives you any hint to the real engine we're using. Oh and we have a low cost "home brew" cool suit cooler we will share. Should save $500 or more over buying pre-made bits.

    Until next time!
    Last edited by Fair; 07-29-2019 at 04:28 PM.
    Terry Fair @ Vorshlag Motorsports

  23. #73
    Fair's Avatar
    Fair is offline Senior Member Supporting Vendor
    Join Date
    Oct 2003
    Location
    Dallas, Texas
    Posts
    3,634
    My Cars
    E36 M3, E36 LS1, E30 318
    Project update for November 29th, 2019: Another long gap since I updated this thread, but we have been busy working on several E46 cars.



    This time we have three E46 chassis we are going to touch on. The first is my 2003 325Ci that has been around for two years but was recently sold. The next is our Team Endurance build, the E46 coupe shown above. There has been a lot going on behind the scenes since my July update - as well as a significant delay that was out of our control.



    Lastly we will talk about this gorgeous Imola red ZHP 6-spd 330 sedan above, which I bought from a customer recently. It has some little issues and CELs that won't be easy to fix. Our plans have already been effected by how hard the black 325 was to restore and sell. So let's catch up!

    2003 BMW 325Ci SOLD

    I bought this clean E46 coupe automatic from a customer in May 2017 - a car we had worked on for him in the past, but when we moved our shop he started going elsewhere for repairs.



    After a few "random" repair shops milked a lot of repair jobs from him over a few years, it got too expensive to drive and for him to maintain in a perfectly functional, super clean form. This is the fate of many E46 models in 2019 - they have aged a bit now, can become plagued with electrical and sensor issues, inevitably they get some problem that throws a CEL (Check Engine Light), and other lights on the dash start to freak people out.



    This car was handed down to one of his college age kids, which did the 325 no favors. It got a bent wheel and delayed maintenance until it just stopped running at one point. I bought it for a good price but if you read the extensive repairs we have detailed here you know I had a lot of time and money in this car. All of the suspension, lots of underhood repairs, the tires and brakes, interior updates, swapped the transmission, etc. It had a CEL that we kept chasing, and I finally threw my hands up.



    This car was never going to be a good candidate for a race car build, as it was a 325 with a slush box. The AC worked but with a CEL it was virtually unsellable. We cleaned it up extremely well, posted some really nice pics and details on Craigsligt then FB Marketplace... all we got was tire kickers and trash pickers. $1000 and $1500 offers, sight unseen - we never even had one person show up to look at and drive it. Sad.

    The car was super clean, and drives great. One of my employees needed a daily so I sold it to him cheap, and lost a bundle on this. But my wife drove it for about a year, so I have to just look at that as "the cost of driving a car". Moral of the story here is: don't buy that "cheap E46" you see for sale, thinking you can fix it up and flip it. This was a 100% Texas car (rust free), straight, super clean inside and out, had D-Force 17x8.5" wheels plus great tires... but with 151K miles and a CEL it was hard to sell. It was sold for half what I had in it. Lesson learned.

    E46 BLOWER MOTOR REPAIR

    Of course this car's HVAC blower motor quit working almost immediately after he bought it, so we fixed that on my dime. Blower motor & blower resister are both a "high failure item". There are detailed links below on both tasks:

    Since I was already selling the car at a loss, we tried the less expensive part that potentially had more labor hours first - the resistor.



    You can access this behind the glove box, and this trick saved some Brad a lot of time on this task. After about 90 minutes the resistor was replaced and immediately started to work, and has worked ever since.

    REPLACING A FRONT FENDER

    This should be an easy one, but I re-learned a lesson here. The left front fender was smashed when we got this rolling chassis for a song - not a big deal, as I keep a couple of pairs of front E46 steel fenders in stock to use for metal flare jobs on E36 chassis (for before - when there were not good flare options). But it had been a number of years since I had bought these fenders...



    Again, we haven't done a steel E36 flare job like this in years - because there are so many good flares and widebody options for the E36 now. The E46 is no different, as I will show below. But I had forgotten that we utilized E46 non-M SEDAN front fenders for our E36 flare jobs. It came down to the recessed trim section in the sedan fenders was further back and "out of the flare" section. That made the welded steel flare jobs on E36 cars easier. We would cut out the fender flare portion of these E46 fenders then graft them to the E36 (see above right). It was a bunch of work but could turn out nice with a little bodywork and paint.



    So when the smashed coupe fender was removed, I grabbed one of these SEDAN fenders, not remembering it wasn't a COUPE front fender. It was on the car for a couple of months - because with the front nose and left side door off it wasn't obvious it was the wrong one. If you look at this fender installed, above right, you will notice the body lines from the A-pillar don't match up - that's all that was visible... So when we test fit the Extreme Dimensions flares (shown further below) it "didn't fit".



    Again - a weird mistake, and it would have been immediately evident if the door was installed. Luckily replacement coupe fenders are still cheap for these cars and I found some for $58 shipped. I used to pay closer to $33 for these import fenders from a local Certifit store, but that's a 3 hour round trip in traffic to save maybe $20. This is one of the few things eBay is good for - cheap used parts or import body parts. Probably won't be the last fender we will need on an endurance car, hehe.

    MOUNTING THE NOSE + TUBULAR BUMPER BEAM

    We aren't 100% done with this step but I will show some progress. The "M3 style" front bumper cover is an import unit designed for use on a Non-M coupe chassis. This is often used by Spec E46 users, and we will utilize this item for the better grill openings and flatter bottom - which makes adding a splitter easier.



    At this point we have the bumper cover mocked up - we needed that for the flare fitment tests. The factory plastic brackets at the tub are holding the receiving "cups" on the bumper cover, with the weight held up by a bucket for now. The cover needs a bumper beam to mount to, with brackets to hold it in place. We plan to have a rolled radiator that is feeding the radiator from the lower grill opening only. to make room for that a tubular bumper beam is a trick we often use to make more room. Here's an example of what we have planned, which we built this year for my wife's LS swapped 86...

    TUBULAR BUMPER BEAM ON 86

    We almost always start with our tubing roller (below left), install the appropriate dies, and then pick a piece of 1.50 x .095" wall, 1.75" x .095" wall or 1.75 x .120" wall seamless DOM tubing. We cut this to length and then bend the main curve to match the bumper cover.



    On this car we were using a carbon fiber aftermarket nose, which had both a curve and needed two bends to kick in for the portions outside of the radiator. Some folks will stop their tubular bash bar at the frame rails, like most OEM beams do. We have seen car-to-car contact rip bumper covers off, destroy headlights, and more. With our full width bumper beams on other cars we have seen our customers "come out on top" of any contact.


    Above left you can see how closely this tubular bumper beam matches the shape of the nose we are using - again, necessitating a couple of bends to kick in outside of the frame rails and under the headlights. This FULL WIDTH beam is much stronger and protective than the "half bumpers" we see some build. The mounting plates are cut on our CNC plasma table then the bar is mocked up underneath the bumper cover to figure out the lengths for the tubing mounts. These are fish mouthed and added to the mounting plates and beam. It is all tacked up on the car but finish TIG welded on the fab bench, above right.



    These pictures above show the rolled radiator - its also only fed from the lower grill opening, and mounted way forward and down. This makes venting the hood much more effective, and we will do the same thing on our E46. The upper and lower radiator mounts will be custom made, of course. We may or may not make a duct box to the hood opening behind the radiator, but we will definitely make the lower grill opening ducted to the front side of the radiator and oil cooler.



    This is as far as we've gotten. On our next weekly work night we should have this tubular beam welded to the mounting plates at the frame stubs, visible behind the bumper in the pic above. Then we will add twin tow hooks to the font, some simple brackets from the tube to the bumper cover, spec the radiator, and build brackets for the radiator and oil cooler. Much more on this task next time.


    FRONT SUSPENSION MOCK-UP

    We bought this car on very worn OEM struts, springs and "mushroomed" top mounts. After some initial work on one of our 2-post lifts this car was moved to a back corner of the shop for the next phase of work, and the OEM struts were tossed. They were total junk. We needed wheels on the car to test fit the fender flares and for our design work on the Brembo BBK, but the OEM stuff was so long that the ride heights would be totally wack.



    Luckily we had an extra Ohlins E46 coilover strut so we found a coilover spring, added a Vorshlag camber plate, and mounted that to the left front. This is not likely our final suspension but close enough for mock-up testing.



    One small downside to inverted struts is the spring and body lengths make it harder to fit "the spring above the tire", which limits how far inboard the wheel can fit. Not an issue with most wheel setups on these cars but "We're going to eleven". We need ALL of that room and more. We mounted one of my E46 17x10" Forgestar wheels and 10.2" wide Hoosiers for the next steps.

    MORE DOOR LIGHTENING



    In my last post I showed how we got the doors down to 29.0 pounds with some serious cutting, gutting, and removal of the window glass and associated mechanisms. We used a variety of cutting tools to get this structure out - including the plasma cutter and some cut off wheels in a pneumatic die grinder. Both methods are loud, noisy, and messy. Plasma cutter is probably the worst way to do this work, as it leaves a super rough edge that we then had to grind or cut away.



    We foolishly forgot to weigh the full weight doors with glass so I don't have a good starting point to reference - but this 29.0 pound weight still seemed heavy for a gutted door, to me. Something didn't "feel" right about that weight. A buddy of mine (Andy) owns Clownshoe Motorsports and said his doors were lighter, so I stopped by their shop one Saturday.



    I can't show many of the endurance racing secrets he shared with me that day, but we did measure some various tires, and noted the technique he uses to gut doors. They leave more of the upper structure but remove ALL of the lower structure, and much of the door striker bits. So we took our 29.0 pound doors and went to town on our next work night.



    Tim and Jason got to work with the Saws-all and it proved to be a more efficient, less messy tool for cutting the door structures. Leaves a much cleaner edge, too. We cut off the ugly edge left by the plasma cutter and then started to work on the metal below the latch plate.



    I then used some extreme care with the cut off wheel and took the upper "crash structure" out at the top of the door, on the inside. The slotted, 3D shape shown in the picture above left. We took this out of the passenger door, and it is heavy. All told we found another 2.1 pounds, which isn't a lot. We had already taken the main crash beam, glass, and regulator out of the door. We were starting to hit a big "diminishing return" type of task.



    Tim suggested we KEEP the upper structure on the driver's door (shown with a red box around it, above left). He crews for two different pro level road race teams that have driver changes, and he has noticed that they tend to lean on the upper part of the door during stops. So we left that in the left door, and it is only 1.1 pounds heavier at 28.0 lbs (above left). This door was weighed after cutting some of the inner structure out and with the window + regulator removed, but the diagonal "crash beam" in place at 34.7 pounds (above right).



    I made sure we weighed the full weight door (above right) on our 2015 Mustang road race project, which is going on a SERIOUS diet and getting an LS swap. 84.2 pounds for a door is extreme, but keep that in mind when you are gutting your door. We might find another pound in these BMW doors, but we have kept structure at the hinges, striker latch, side mirror mount and along the top of the driver's door. Any additional weight removed is going to make the remaining door compromised... I think we are there.

    continued below

  24. #74
    Fair's Avatar
    Fair is offline Senior Member Supporting Vendor
    Join Date
    Oct 2003
    Location
    Dallas, Texas
    Posts
    3,634
    My Cars
    E36 M3, E36 LS1, E30 318
    continued from above

    BREMBO E46 BIG BRAKE KIT

    I teased this last time, and I'm not going to share everything now - because this brake kit is currently untested. We could have just bolted on E46 330 brakes, which are an 1" larger in diameter from the base 325/318/328 brakes, as shown below. We've done this cheap upgrade on a number of 325/328 cars before. But this car is going to be in WRL GTO class (more on that below), with V8 power and 315mm tires... it needs MORE BRAKES.



    We started developing this swap kit last June and tested 6 different rotors and a few calipers. I bought a number of rotors, including the E46 M3 325x28mm, the ZCP competition M3 2-piece rotor which is 345x28mm (and $$$), and some other rotors. We mocked up the Powerbrake caliper on a number of these but the prices start ti get extreme if we use that caliper.



    We kept coming back to a particular Brembo 4-piston caliper, which we have a lot of experience with. This is not a radial mount Brembo like the Porsche calipers some BBKs are based on. Those Porsche calipers need to be machined and still require a somewhat expensive caliper + core to work.



    We attempted to use this with the E46 M3 rotors but the spacing for the Brembo, but with the somewhat "small" diameter 12.8" E46 M3 rotor, the spindle mount spacing just didn't work well for this caliper's mounts. And honestly we wanted a bigger rotor for endurance racing - which is where we see this kit working well, as the E46 is a popular endurance race car chassis. We actually made a bracket to where this Brembo to this M3 rotor but the caliper had to scoot "up" enough that part of the pad sat above the rotor. That's going to make the pads wear poorly so we abandoned this M3 rotor. Shame.



    Next we tested a number of larger non-BMW rotors with the same 5x120mm bolt patterns, including this 1-piece 13.6" (345mm) above left and a 1-piece 14.0" (355mm) rotor above right. Even though we would be going to an 18" diameter wheel for our car, we knew many endurance E46 racers wanted to stick with 17" wheels, so we used our 17x10" Forgestar as the "go / no go" gauge for our brake fitment testing. We even tried a 14.5" rotor but it was too tight for safe use inside this 17" wheel.



    The best fit for the 4 piston Brembo caliper on the E46 non-M spindle was on the 14.0" diameter rotor (355mm x 32mm), which is a monster. It had the right bolt pattern but we had to slightly re-machine the opening to fit over the BMW hub. Myles used our CNC lathe to make this cut and it worked perfectly. This rotor weighed 24.0 pounds before we machined the hub and chamfer. Very cost effective.



    I am not showing our E46 mounting bracket just yet - we made prototype brackets that bolt-on without mods, but they aren't production quality looking yet. Once we get some laps on this brake setup, and if they work as well as they should, we will sell this as a kit (rotor, caliper, bracket and hose). Gives us BIG brakes, affordable calipers and rotors, with a massive pad selection. Fits within some 17" and all 18" wheels. Stay tuned for more.

    DURAFLEX E46 M3 WIDEBODY KIT

    I teased this last time as the widebody kit had just arrived but we hadn't mocked it up well yet. We needed the bumper cover, left door, a wheel and suspension, and the correct left fender mounted to test flares these completely. All of those other other steps have been completed so now we could finally test fit these bits properly at all 4 corners.


    We were excited to try a widebody kit that we could buy for so little. This looked good for both clearance and minimal drag. The aero of a fender or flare matters, especially when you are bombing down the back straight at COTA going 150+ mph. We found out later that the images used by Duraflex on their website are only 3D renderings, and even those are from a competitor.



    We got the kit that we ordered (we are a dealer) and the fit and finish was pretty good - we have used a number of items from this brand and quality can be a bit "all over the place", but this was one of the better fitting setups. We spent several weeks rounding up a LF fender, mounting the nose and hood, getting the driver's door on, and mounting the suspension/wheel/tire/brakes - before we could mock these up properly.



    These are made to work with the M3 nose and M3 lower skirts, so we had a gap at the bottom where the skirt was supposed to be. But we have some M3 skirts laying around, that won't be a big issue. The fronts and rears both fit surprisingly well. The rear had plenty of tire clearance...



    ...but the front will only clear a 275mm tire. That's the problem with looking at the drift or stance communities for flare options - they never run a lot of actual tire WIDTH, just going for the stance or a tire that makes lots of smoke.

    WIDEBODY KIT FOR SALE!

    These flares won't fit over our 18x11" wheels up front, but for a racer or team running a 275mm tire on a 10" wheel, this should be ideal. Interested? We'd sell this whole kit at a loss for $400 shipped - call us at the shop if you want this set. Only mocked up, never drilled or bolted on.

    ORDERING A CAGE KIT

    Many of you know that Vorshlag is known for making higher end roll cages in road race cars. But if you have read this post titled "we make roll cages" you might realize that our cages cost a bit of money. Because they take a long time to plan, prep, bend, notch, fit, and weld. 60-75 hours is normal for a car like this.



    Spending 75 hours building a cage from scratch - after hours and in our free time - could takes several months to complete. We tried to shortcut this time by ordering a "cage kit" from a reputable shop known for perfect fitting BMW cages. These are pictures of the kit built for our car, remotely, using another E46 coupe chassis to build within.



    Back in May the team voted on this option, and then paid for this E46 kit from Hanksville Hot rods. They build their kits inside the same chassis as you ordered - but it took longer than expected to round up an E46 coupe to use. And longer still to complete the kit. Stuff happens.



    This was an experiment to see how many hours we could save by ordering a kit and just doing the final welding here. It likely will save a 40+ hours of fab time, once it is complete and in the car, but our 6 month wait to get the kit built did nothing beneficial for our build's timeline. We had hoped to be on track in the Fall of 2019 but we are now pushing into Spring of 2020. We will show more of this kit being installed into our chassis next time, then many things staged behind this will follow.

    SEARCH FOR NEW FLARES - CLINCHED

    After the Duraflex kit proved to be too small up front for us we immediately started looking for an option that could clear our 18x11" wheel and 315/30/18 tire we will be using. Since 2017 "Clinched" has been making some stancey widebody kits and flares. They make a series of "universal" flares from thermo-plastic, which are formed on a vacuum table - a technique which we have used in the past.



    We had started to see these show up on legit road race and autocross cars with BIG wheels. A buddy had purchased a set of their "Euro" style flares with 100mm (4") widths. They worked to clear a 335mm tire on his Subaru track car (below left) and the same units on this CTS-V road race car looked pretty good. This style is made to be trimmed to fit, then bolted on.



    We borrowed this 100mm Euro flare and mocked it up on both ends of our E46 coupe. They have more room than the front Duraflex widebody kit.



    This won't be as clean of an install as the E46 specific widebody kit, but it will give us full coverage on the protruding part of each tire, and we can vent behind each tire by trimming the flares short on the back side. We became a Clinched dealer a month ago and ordered a set of flares this week for use on this car. We will show that installation work in a future post.

    GTO CLASS + BUILDING THE ENGINE

    We have been staying quiet about the engine, but it's Vorshlag - what did you think we'd build? Of course an LS swap is in order for our E46! Look how good an LS V8 fits under the hood of an E46...



    An old prototype set of our stainless long tubes was rounded up, we built some mounts, have a brand new transmission which we will test (which I cannot talk about yet), have an E46 M3 rear subframe and diff to use, and more.



    Once we agreed upon the class we wanted to run (GTO) then the engine we would use became obvious - an LS V8 engine.



    Even running the highest class in WRL (GTO) we are still limited to a fairly tame 9 pound per whp. And unlike NASA ST/TT classes, they calculate with no driver (but full of fuel). We need to know what the car will weigh then figure out how much power we can make...



    We haven't done a W2W prepped E46 LS build yet, but we did build a caged E36 with a 427" LS engine and T56 Magnum before. This was our "Alpha" E36 LS build, which we raced from 2006 to 2009. Fully caged, with a fire system, aluminum LS, full exhaust, oil cooler, big radiator, Accusump, heavy 17x11" CCWs, all of the factory glass except the doors (which were gutted), and a single racing seat it tipped the scales at 2508 pounds, without fuel. The E46 chassis is a little bit heavier, plus it will have full aero + driver cooling system - so lets call it 2750 pounds full of fuel and race ready.

    2750 lbs / 9.0 = 305 whp

    This peak number of just over 300 makes a BMW M54 based engine out of the question. And yes, we could have built a higher strung S54 E46 M3 engine for this car, those aren't exactly inexpensive or known for massive reliability in endurance racing. Costs for an LS are much lower for us, and we are known for LS powered BMWs, which pushed us to an aluminum LS. We could make this with the smallest displacement 4.8L truck engine, or easily with a stock 5.3L. But we are going to "overshoot" our power goals, then dial it back with a using a custom "flat tune" by way of a factory Drive By Wire (DBW) throttle body. You could do the same thing with a physical restrictor in front of the throttle body, too.

    continued below

  25. #75
    Fair's Avatar
    Fair is offline Senior Member Supporting Vendor
    Join Date
    Oct 2003
    Location
    Dallas, Texas
    Posts
    3,634
    My Cars
    E36 M3, E36 LS1, E30 318
    continued from above

    SOURCING THE CYLINDER HEADS

    We had just pulled a 5.3L LS based iron block engine from the dead carcass of my old shop truck, a 1999 GMC Sierra 1500, #TruckNorris. This truck was smashed into while I was sitting in traffic by a 1 ton van going 60 mph. Destroyed my truck, bent the frame, shoved me into a parked truck and trailer also stopped in traffic ahead of me. Don't text and drive, kids!



    That "LM7" series 5.3L is still an LS based engine, and the "706" castings are a small-valve "cathedral port" aluminum head. This article describes the 706 heads pretty well. They are probably some of the worst performing factory aluminum LS heads out there, but we can still make them work well enough to easily exceed 305 whp - and beyond. This is part of a test...



    Erik at Horsepower-Research (HPR, where I am one of the managing partners) is helping us build this car, and will co-drive in endurance races. He disassembled these heads, then we cleaned them up in the aqueous parts washer before running them for about 15 minutes in the Ultrasonic parts cleaner. The flat stone shown above right was used to knock some of the carbon deposits off the block surface, as well as check for flatness. The heads checked out great even after 273K miles of truck use. The ports still had some carbon but the CNC work will take all of that out.



    Most of the valvetrain will not be re-used, and the now bare castings have been sent off to a head porter we use for a "single pass" CNC port program. These will be assembled with steel (not titanium) valves, for our fairly modest power goal. HPR is known for BIG displacement LS engines, but these heads will be a test for an LS engine we want to develop for more economical endurance racing use.

    THE INTAKE MANIFOLD

    The intake manifold we use for cathedral port heads - along with the camshaft - will determine where in the RPM range the engine will make the most power, and can unleash more on top with aftermarket designs like the Fast or MSD. We might cut the hood later, but we wanted to stick with a low profile "car" style LS intake to start with.



    We cannot fit the taller Truck style LS intake (above left) under the hood of an E46, but they do make good power even with a smaller 75mm throttle body limitation. The 75mm mechanical throttle body versions of the LS1 and LS6 intakes are a bit snug to the E46 hood, but we made 490 whp on a 427" LS engine (above right) that was in our Alpha E36, back in 2008 - also built by Erik Koenig.



    The other low profile cathedral port intake we can use is from the LS2. These use a 90mm DBW (Drive By Wire) throttle body, which is significantly larger than the LS1 or LS6 intakes' 75mm throttle body. The LS2 DBW throttle body setup is also much "shorter" (front to back) than the later LS6 Corvette DBW TB, and the 90mm LS2 style is very cost effective, too. We have seen a good power bump by going to ever larger throttle bodies... there is almost no limit of how big you can go. 102mm is common and we've seen our 468" LS engine pick up power at 105, 108, and even 112mm throttle bodies.

    I did a bit of research on the Dorman brand of replacement LS intake manifolds and this 615-901 "LS2" model with a 90mm TB opening was a real bargain. I hadn't seen much online about this new Nylon intake offering from Dorman so I bought one and we took a closer look. It arrived and looked pretty much just like an LS2 intake. This Dorman intake is only $215.99, and its brand new. A lot of the used LS2 intakes we see for sale have cracked bosses because they are all 10-14 years old. Plastic ages...



    The Dorman 615-901 intake's casting looked pretty good except for two locations: There was a weird "protrusion" in one corner of the intake port near the cylinder head (above left), plus the throttle body opening had a lot of weird casting flaws and gaps (above right).



    I had engine builder Erik take a look and he said he could fix the flaw in each of the 8 intake ports, then we could port then epoxy the small gaps at the throttle body area. At one of our Team work nights he used a long reach porting carbide cutter and smoothed out the protrusion.



    We think this was a flaw in the internal casting dies - something shifted, and nobody bothered to fix it. Same goes for the throttle body section of the casting, where it meets the main plenum portion of the manifold. Just not a smooth transition there, lots of casting flash that had to be removed.



    The part is even made in the USA, which is weird. Maybe Dorman will have this worked out at some point - just know this LS2 unit might need some work. He was done porting the intake ports and throttle body opening in about 90 minutes, and I cleaned the intake in the parts washer at HPR later that week.

    THE BLOCK WORK

    We wanted to start with an aluminum LS block, as these are 80+ pounds lighter than the cheaper iron LS blocks. We could have sourced an aluminum 5.3L truck engine, which has a 3.780" bore. This is as small as any LS engine (4.8L is the same), and restricts the size of the intake and exhaust valves. So we looked for one of the 3.900" bore LS engines (LS1, LS6), which I happened to have. The 4.000" bore LS2 or 4.065" LS3 blocks would be even better, but those are more costly and I had a clean LS6 block I donated to the cause.



    The block was equipped with the OEM 6-bolt main caps (they are worthless without mains!) and it was mounted to an engine stand to take those off.



    Once you get the bolts out these mains are a bit tricky to remove cleanly. Erik has this custom set of main cap pullers one of his employees made years ago and I used it to pop the mains out out of the block. Each main was stamp marked before removal, of course. The thrust bearing is on the 3rd main, as shown in the middle of the block in the above left pic. The main bolts were kept but will likely be replaced with ARP studs.



    We mounted the block to Erik's mill, which he has setup for block work. The goal was to clearance this block for a 4.00" stroke crank, up from the stock 3.622" stroke crank used in the 5.3L or the 5.7L LS6. If you want to do the math, it's easy:

    ((3.900" bore ^2) x Pi / 4) x 4.000" stroke x 8 cylinders = 382.3" or 6.3L

    This extra displacement only makes the engine more reliable at the power level we are targeting - as we can make more torque at lower RPMs with the added displacement. We do this "make it bigger" trick normally to make more total power, which it does. But on any engine, more RPMs = more problems, and on an endurance engine, we can make the same power goal at lower RPMs. We ran his crank clearance program for this LS6 block and a 4.0" stroke, which takes about 45 to 60 minutes. This is to allow the connecting rod to clear the bottom of the block's cylinder casting with the additional stroke.



    Next up the block was mounted to the surfacer, and the decks were surfaced the bare minimum to make sure they were perfectly flat and square to the bore centerline. With less than .005" removed the block cleaned up perfectly. There are more steps - line hone, bearing checks cleaning - but I will show more of the shortblock work next time. And we have a second engine, an aluminum 5.3L, that we are setting up as a back-up engine as well.

    2004 330i ZHP

    Another customer tired of dealing with lots of little issues like CELs reached out to me this month and wanted to unload this Imola Red 6-speed ZHP sedan. It is out of inspection and registration, and the AC is blowing hot, so it's pretty much unsellable in Texas.



    This is a one owner Texas car, however, and it has some tasty upgrades. A 3.64 geared limited slip diff, coilover suspension he bought from us over 10 years ago, 18x9" wheels, Michelin Pilot Sports, a Setrab oil cooler, and more.



    With 162K miles, the AC system on the fritz, and these CEL issues it isn't worth a lot of money as it sits - and I don't want to fall into another "let's just find the issue and sell it" trap, as the risks of these being easy fixes are nil. We went and drove the car, however, and it is really nice. Super clean inside and out - this was owned by a BMWCCA member who cared for this car - until it became more of a burden than a joy to drive. I brought a trailer to tow it back home, since it had no plates.



    Not really sure what we are going to do with this car - we take it to lunch on nice days and it gives me bad ideas. How about a nice daily driver with a 500 whp V8? I bought this E46 M3 rear subframe (and we have a 210mm LSD M3 diff) just in case we move forward with a swap.

    WHAT'S NEXT?

    That seems to be enough for this time, but we will have much more to show on the next update. We should have some progress to show on the Team Car ...



    We have a few 210mm M3 LSDs and it is cheaper to use one of these than convert the medium case 188mm E46 non-M diff. So I donated an E46 M3 rear subframe (not the same one that I bought for the ZHP) for this E46 endurance car. This has had the bushings pressed out and bead blasted - next time we will show the reinforcements we are adding and the new bushings going in.



    We will also show the sealed spherical bushing we installed in the RTAB location, which is pretty slick. Also the cage install, electric assist steering column, and more. Lots to do!

    Until next time...
    Terry Fair @ Vorshlag Motorsports

Page 3 of 4 FirstFirst 1234 LastLast

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •