There has been interest in a heat shield for the valve cover to keep ignition coil wiring from melting, so I made up a few shields to try out. They are made of aluminum, and will fit both OBD1 and OBD2 valve covers. I've gone through a few iterations and found dimensions that fit nice and snug without rattling. Also included would be knurled nuts to mount these to the stock studs (I have extended studs in the pictures for testing fitment. Included nuts will sit flat on the cover).
There are many options for colors/finishes:
Raw
Polished
Red, Black, White etc (high quality paint that comes on industrial sheet metal).
Powdercoated (would be a little more cost added - probably around $20-30)
Pricing is $110 shipped.
I can get raw, polished, and painted ones shipped starting about one week. Powdercoated would take a little bit more time, and will only happen if there is enough interest to do a batch, so I will gauge interest on that. Thanks.
Last edited by cj.surr; 04-17-2015 at 01:07 AM.
I'd take a polish 1 for ob2 ..asap
Good work.
If you build it, they will come.
"
I'll take one, raw obd1. PM me your paypal.
She's built like a steakhouse but handles like a bistro
I'll take one 0d1 need paypal info
Are you still making these? Or do you have any for sale?
I'm interested in one as well if they're still available
Likewise I would like one as well if still avail
Me too
96 M3, GT4094R, Arrow Rods, CP Pistons, Elring HG, cutring 87mm, 10 mm ARP studs,MS3pro, EMC Intercooler, n54 6 speed with Motiv twin disk, ZT-2 wideband, Zionsville Radiator, X-brace, H&R springs with bilstien shocks, QTP electronic cutout, Line Locks, stock exhaust 455rwtq, 453rwhp at 14 psi 91 octane.......684rwtq, 681rwhp at 24 psi running flex fuel E60 at time of dyno tune.
I've had a lot more interest as of late (it must be getting hot out) so I've decided to do another run of these. About 1 week to ship Priority Mail.
Please PM me or email at cj.surrusco (that's a gmail) if you would like to order one.
Thanks, CJ
Last edited by cj.surr; 07-20-2016 at 08:30 AM.
All orders have shipped out. I have made a few extra that are available (pictured on right), they can be given a brushed or polished finish. Two of them do not have the small bend on the bottom (mostly cosmetic).
13978391_579004112303458_169995656_o by Cj Surrusco, on Flickr
I will take the one with the bend at the bottom.
Comes with the hardware to install?
Old set up: 520RWHP & 500RWTQ @ 20PSI 1/4 mile as of 7/26/15 12.5 @ 125MPH - 19PSI
New set up: Steedspeed Twinscroll, Wiseco Pistons 8.8:1 CR, K1 Rods, Blueprinted and Balanced, ARP Main Studs, o-ring block, GTR 12mm head studs, GT35R with 86mm HTA billet compressor wheel (GT3586RHTA) TwinScrol 1.06 exhaust housing, Nick G custom tuning, 6 Speed Transmission, UUC Twin Disc Clutch, UUC EVO III, UUC DSSR 109mm, EVO 6 Speed Driveshaft, HFS-6 W/M injection, Zeitronix data logger, 3" SS full exhaust, Rallyroad strut bar, X brace, Race coilovers.
Bump, I still have the last few left if anyone is interested.
Forgot it about this!
Still have the one with the bend at the bottom?
Old set up: 520RWHP & 500RWTQ @ 20PSI 1/4 mile as of 7/26/15 12.5 @ 125MPH - 19PSI
New set up: Steedspeed Twinscroll, Wiseco Pistons 8.8:1 CR, K1 Rods, Blueprinted and Balanced, ARP Main Studs, o-ring block, GTR 12mm head studs, GT35R with 86mm HTA billet compressor wheel (GT3586RHTA) TwinScrol 1.06 exhaust housing, Nick G custom tuning, 6 Speed Transmission, UUC Twin Disc Clutch, UUC EVO III, UUC DSSR 109mm, EVO 6 Speed Driveshaft, HFS-6 W/M injection, Zeitronix data logger, 3" SS full exhaust, Rallyroad strut bar, X brace, Race coilovers.
Great seller, great product. Had some shipping Issues and CJ handled it immediately. Highly recommended. Thanks
I had no issues with fitment or shipping. This is an awesome piece!
Do you think you can make a fuel rail cover to match?
Old set up: 520RWHP & 500RWTQ @ 20PSI 1/4 mile as of 7/26/15 12.5 @ 125MPH - 19PSI
New set up: Steedspeed Twinscroll, Wiseco Pistons 8.8:1 CR, K1 Rods, Blueprinted and Balanced, ARP Main Studs, o-ring block, GTR 12mm head studs, GT35R with 86mm HTA billet compressor wheel (GT3586RHTA) TwinScrol 1.06 exhaust housing, Nick G custom tuning, 6 Speed Transmission, UUC Twin Disc Clutch, UUC EVO III, UUC DSSR 109mm, EVO 6 Speed Driveshaft, HFS-6 W/M injection, Zeitronix data logger, 3" SS full exhaust, Rallyroad strut bar, X brace, Race coilovers.
PM'd you for one with the bend on the bottom
98 Fern Green M3/2 - Precision 6870/AR Designs Twin Scroll/RK/E85
2017 Toyota Tundra Crewmaxx - Family Whip
2011 Pierce 75' Quint - Fire Apparatus West Islip FD
Bump for a good human.
Still making these CJ?
Sent from my iPhone using Tapatalk
THE TIME DRAWS NEAR!
really wish someone was still making these
Bookmarks