Page 16 of 16 FirstFirst ... 678910111213141516
Results 376 to 392 of 392

Thread: Laminar's M3 5.0 swap: Fünf-Null

  1. #376
    Join Date
    Mar 2011
    Location
    PNW
    Posts
    551
    My Cars
    LS E46
    Hey genius, the point is snow doesn’t hurt anything. And no one cares where you are. No one was asking.

  2. #377
    Join Date
    Dec 2014
    Location
    Des Moines, IA
    Posts
    754
    My Cars
    '97 M3/4/5.0
    Quote Originally Posted by Tim Mc View Post
    Any consolation - I find myself in snowy Stuttgart for a few years thanks to my families desires.
    Ooo, I had wondered where you were going when you had to pack the M3 away. Living abroad is a very cool experience, I hope you're enjoying it!

  3. #378
    Join Date
    Apr 2012
    Location
    Stuttgart, Germany
    Posts
    440
    My Cars
    1997 M3 / 5.3
    We would have loved to bring the M3 over, but it wouldn't get past the custom docks at Bremerhaven. Disappointing, I just eyeballed a near mint E36 four door...just before it was crushed. Sad - not many junk yards here and seemingly few older models on the road. I've only seen a couple E36's. Many environmental rules - creates challenges for car fun. Heck I can't even wash my car at home...must be at a car wash due to the run off.

    The Cougar is a unique cat! That is an undertaking, but quite satisfying when complete...

  4. #379
    Join Date
    Dec 2014
    Location
    Des Moines, IA
    Posts
    754
    My Cars
    '97 M3/4/5.0
    Back at it! SCCA chapter is doing a dyno day for the Time Trials series, so I'm piggybacking on that to see what kind of massive power my little 5.0 puts down. That's just a few days out, so it would make sense that I finally dig my car out of the snow and tear it apart.

    Since doing the engine work, I noticed that one bank was consistently richer than the other. This could be an exhaust leak before the O2 sensor, or it could be an injector problem. My injectors are 36lb units I bought used off of eBay and slammed straight in the car. I decided to pull and clean them.



    I made up a little block to clamp the injector in place both ways. First, blow cleaner through backwards to clear out anything hiding inside. Then blow through the correct way to see if the spray and pattern look good.



    To cycle the injector, I grabbed a spare pigtail from my stash:



    And wired it up to the #1 injector on the engine. Then I put the Megasquirt in test mode and had it pulse the injector a few hundred times. (sorry, you have to scroll to the right to get to the video)

    https://www.instagram.com/p/Bu7tMPXAtIR/

    I was initially planning to actually flow test the injectors - I started modifying a spare fuel rail to hook up to an external fuel pump and spray into a graduated cylinder for measurement, but I'm not sure I have the time right now.

    I also wanted to address cooling. It got as hot as 230 on the track last summer, so I wanted to do what I could to help it cool down a bit more.





    I'll remake those out of some corrugated polypropylene and fix them in place, hopefully that directs a bit more air to the radiator and helps keep things cool.

    I need to get the intake put back on, change the oil, and dial the tune in before Saturday.
    Last edited by Laminar; 03-13-2019 at 11:13 AM.

  5. #380
    Join Date
    Dec 2014
    Location
    Des Moines, IA
    Posts
    754
    My Cars
    '97 M3/4/5.0
    When the engine got warm last year, I had a badly cycling idle. I tried all of the tuning tricks I could, but I couldn't ever get it to settle down and it would occasionally make the car die.

    With everything apart, I'm trying to eliminate any possible hardware problems. I cleaned and oiled the air filter. I cleaned the MAF sensor. I'm inspecting for vacuum leaks. I'm also looking at the PCV system. Changing cams changes vacuum which messes with the PCV. The valve I had in there was an aftermarket replacement for a carb'd Mustang 302, a part number 2221. When digging around in my bag of hose clamps and vacuum fittings I found another PCV valve stamped "2313 MADE IN USA." Some digging tells me this is for a stock Explorer 5.0. Some more research tells me that all aftermarket PCV valves are garbage.

    I ordered a Motorcraft EV98B, which is for a stock Mustang. It was all of $6 vs. the cheapo $2 aftermarket units. I wish there was more data out there on the factory units and their specs. I know someone makes an adjustable PCV but for $130 I can buy and try a lot of different valves.

    Anyway, I finished up the radiator air routing. I'm still planning to install a splitter which will seal off the bottom of the radiator. Maybe I'll throw some more of the plastic down there to seal it off until then. Couldn't hurt...



    I also changed the oil and did a quick check of the front suspension. I refreshed it all last year and it seems like everything's still tight. Tonight I need to do the same at the rear and take all of the rear camber out for maximum dyno gainz.

    Also I did something dumb.



    The car gets parked outside so I try not to make it too embarrassing for my wife (basically the only thing preventing me from putting a big ol' wing on it). We'll see how long these last.
    Last edited by Laminar; 03-15-2019 at 09:50 AM.

  6. #381
    Join Date
    Oct 2004
    Location
    DeWitt, Michigan
    Posts
    5,869
    My Cars
    '97 540i/6, '97 328i

  7. #382
    Join Date
    Sep 2014
    Location
    North OC, CA
    Posts
    2,442
    My Cars
    E39 530i5 Sport, E39 M5
    The stripes are great. Keep 'em on as long as you can!
    Nate J. - Build Log
    (oOO\(|||)(|||)/OOo)

    Reliable P.O.S. - Green/gray 1995 Camry V6 LE. 255k mi+.
    “Peyton” (WIP) - TiAg/Schwarz Nappa (M1SW) 07-18-2001 M5 Heritage (BZ99672). 164,220mi. Sidelined with a rod knock :'(

    RIP, Seabiscuit. Black Sapphire/Schwarz 03-11-2003 530iA Sport (CK39185). T-boned 03-01-2017 at 155,861mi.
    Take 2 "Otto" - Toledo Blue/Sandbeige 04-25-2002 530iA Sport (CH98032). Sold 11-10-2017 at 147,743mi.
    Take 3 "Manuel" - Toledo Blue/Grau 10-29-2001 530i5 Sport (CE92358). Sold 02-01-2019 at 217,600mi. I'm gonna regret that.

  8. #383
    Join Date
    Apr 2012
    Location
    Stuttgart, Germany
    Posts
    440
    My Cars
    1997 M3 / 5.3
    Agreed!

  9. #384
    Join Date
    Dec 2014
    Location
    Des Moines, IA
    Posts
    754
    My Cars
    '97 M3/4/5.0
    Gassed up and headed out.



    Started by getting it weighed. This is with full interior (driver's seat swapped with racing seat), 3/4 tank of gas, no A/C.



    Tim Mc weighed his stock '97 M3 sedan non-luxury package (manual seats) at 3237 with no fuel. The last time I weighed my car with the iron heads and both stock front seats and almost no fuel it was 3277. So it looks like my head swap/header build/seat swap took out over 100 lbs. If I swapped out the passenger seat and took out the fuel it'd be below 3100.

    And what about power? It was a little less peak than I was hoping for, but still decent for a worn out high mileage junkyard shortblock with some Craigslist parts slapped on. The torque curve is a beauty and exactly what I was going for with the Explorer intake and long tubes - over 300 by 3000rpm and hp carries to about 6000 before dropping off too much. This puts me smack in the powerband from 30-65mph in 2nd gear, perfect for everything but the slowest of turnaround corners. And I have the rev limiter set at 6250 so I can hit 70mph in 2nd for those extra long straights. If I swapped to a 3.73 rear end I'd drop down to about 25mph but top out at 60. That'd be a good tradeoff for the low speed courses we sometimes see but it'd hurt on the fast courses.

    278hp@5200, 312tq@3700.





    Video:
    https://www.instagram.com/p/BvFUS99gyPF/

    Car made the 80 mile round trip without a hiccup!

  10. #385
    Join Date
    Apr 2012
    Location
    Stuttgart, Germany
    Posts
    440
    My Cars
    1997 M3 / 5.3
    Laminar,

    Great update - always a good feeling to see results from your blood, sweat, and tears!

    A 100 pounds is substantial...= more HP.

    I would have topped up the tank before weighing - less variables, but in the big scheme of things likely just +/-20 pounds...

    The E36 is still one of the better looking cars out there.

    Thanks for keeping the thread alive!

  11. #386
    Join Date
    Dec 2014
    Location
    Des Moines, IA
    Posts
    754
    My Cars
    '97 M3/4/5.0
    Quote Originally Posted by Tim Mc View Post
    I would have topped up the tank before weighing - less variables, but in the big scheme of things likely just +/-20 pounds...
    You're right - I didn't even think about weighing the car when I left, I forgot they were doing that. I like to run autocross events at about 1/4-1/2 tank so I put enough in to get me there, back, some tuning, and to my first event.

    Reviewing the datalogs shows I was only running 33 degrees of timing (small block Fords typically are happy with 34-36) and my AFRs were a bit rich at 12.5. Some timing and tuning could release another 5-10hp pretty easily.



    The only thorn in my side right now is the oscillating idle. It's better than it was before, but not perfect, and it likes to die when the revs first drop when the clutch goes in. Once the idle settles it's fine, but the thing died several times while the guy was trying to drive it off the dyno, which was a bit embarrassing.

  12. #387
    Join Date
    Mar 2007
    Location
    Austin, TX
    Posts
    4,320
    My Cars
    18 Colorado Z71, 88 325i
    Nice Car is probably a blast.

  13. #388
    Join Date
    Jul 2012
    Location
    Herndon, VA
    Posts
    453
    My Cars
    98 M3/4/5, RIP 528e
    Congrats on the solid numbers, puts my S52 to shame! But now I'm curious to see if my car makes what I think/hopes it makes. Are you still planning on doing some rally-x events this year?

  14. #389
    Join Date
    Dec 2014
    Location
    Des Moines, IA
    Posts
    754
    My Cars
    '97 M3/4/5.0
    Quote Originally Posted by 95maxrider View Post
    Congrats on the solid numbers, puts my S52 to shame! But now I'm curious to see if my car makes what I think/hopes it makes. Are you still planning on doing some rally-x events this year?
    Good question - for this event I jacked my coilovers all of the way up. You can see from the pics that even at max height it still appears to be lowered. The exhaust hit the lift as he was trying to back it on the dyno. It's...low.

    The front springs are 6" x 525lbs (9.3kg/mm) and the rears are 6" x 700lbs (12.5kg/mm). I could buy springs of the same stiffness but 2" longer. At max height the car would be 2" taller, but the coilovers still have enough adjustment to drop it down to autocross height.

    In reality, RallyCross and Autocross call for very different spring rates. I'm wondering if I could find a compromise that would be stiff enough for road course work but not knock my teeth out offroad. I don't want to change the front springs back and forth, messing up the alignment.

    Apparently they're running a new venue on a local dirt track that's hard-packed and fast. I want to try to make it out there if I can, that's the kind of course I can handle.

  15. #390
    Join Date
    Jul 2012
    Location
    Herndon, VA
    Posts
    453
    My Cars
    98 M3/4/5, RIP 528e
    Quote Originally Posted by Laminar View Post
    Good question - for this event I jacked my coilovers all of the way up. You can see from the pics that even at max height it still appears to be lowered. The exhaust hit the lift as he was trying to back it on the dyno. It's...low.

    The front springs are 6" x 525lbs (9.3kg/mm) and the rears are 6" x 700lbs (12.5kg/mm). I could buy springs of the same stiffness but 2" longer. At max height the car would be 2" taller, but the coilovers still have enough adjustment to drop it down to autocross height.

    In reality, RallyCross and Autocross call for very different spring rates. I'm wondering if I could find a compromise that would be stiff enough for road course work but not knock my teeth out offroad. I don't want to change the front springs back and forth, messing up the alignment.

    Apparently they're running a new venue on a local dirt track that's hard-packed and fast. I want to try to make it out there if I can, that's the kind of course I can handle.
    Wow! How do you still have your front bumper in one piece? I put on the non-M version before even trying to rally-x. I'm running no-name 250lb 12" front springs and 400lb 7" TC Kline in the rear. A big turning point for me was swapping out my former normal coilover-style 7" Hyperco rears to the Klines, which are an OEM beehive-style spring. This completely got rid of the coil binding I was getting, and I was getting it a lot. I'm very curious to know how your car rides in the dirt! What tires do you run for rally-x? We made the switch to a hard packed dirt place last year from loose stuff the years before, and I went from not being in the top 5, to being the season champion. I suggest you go to all the events there that you can!

  16. #391
    Join Date
    Dec 2014
    Location
    Des Moines, IA
    Posts
    754
    My Cars
    '97 M3/4/5.0
    The front bumper may actually be in a couple of pieces...

    I have a set of Blizzak LM-25s in a 205/50-17 with wheels I bought off of Craigslist. That's what I've run in the past. I'm keeping my eyes peeled for something in a 215 or 225 and 50 or 55 to give me a bit more sidewall and ride height.

  17. #392
    Join Date
    Aug 2009
    Location
    Metro DC
    Posts
    815
    My Cars
    79 323i, 94 325is, 13 M3
    Thanks for going to the hassle of doing a dyno and posting it. It's nice to see real numbers. Sorry I was too busy to do it with my stocker with the intake/cam swap.
    If God meant for man to motor-swap LS engines into track cars, He wouldn't have created Corvettes.

Page 16 of 16 FirstFirst ... 678910111213141516

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •