What did you buy for your e36 M3 this week v3.0

[M3Dynamic]

dr. vanos

[jesus619]

Motor mounts, trans mounts, guibo, center support bearing and idler pulleys

[M3Dynamic]

Motor mounts, trans mounts, guibo, center support bearing and idler pulleys

make sure you tq that guibo... ask me how i know

[jesus619]

make sure you tq that guibo... ask me how i know

How do you know? Lol jk. Def gonna tq that sucker, thanks for the tip. Point me in the right direction for ss headers or raceland better? All I need is headers, bbtb and cat delete to be full bolt ons lol

[M3Cosmos]

Activated carbon canister shut off valve + 4 O2 sensors to get rid of check engine light. Seat belt tensioner to get rid of airbag light. New door handle trim. New flasher relay so hopefully my turn signals will work again.

[mboor]

just picked up a set of DS2's in near mint condition. Been wanting a set since i bought my M. i'll keep the contours for track tires (if i ever have time to make it to the track)

[SamGrant951]

3.0 euro cluster, new bulbs, new pin/wire for oil temp, rally road oil block, VDO sender, Z3M ASC delete boot, z3m idle valve hose.

[TriniSpeC]

Condor speed differential and subrame bushings, new armrest.

[mchang]

99 M3 coupe

[jpineda504]

M50 manifold!!!

[havasusteve1]

Actually bought picked this up from Amir @ Avus earlier this week. Waited until it was tested and true at the track (today). Beautiful piece, well constructed and functional. Some of the best money spent! In combination with true R-Comp tires and a 3.64 differential, I bettered my best time by 3.9 seconds today @ Auto Club Speedway.

Cheers

[GG///M3]

Where did you pick up the 3.64?

I purchased these.

[havasusteve1]

[QUOTE=GG///M3;28334086]Where did you pick up the 3.64?[quote]

a guy in SoCal who buys them, tears them apart, inspects them, builds them to spec, replaces what needs to be replaced (e.g. Pinion gear; clutch pack etc.) and re-specs the tolerances then re-seals them.

Sergio: (818) 261-6876

[RRSperry]

Mcoupemindy in Virginia builds diffs too.

[doktor b]

Actually bought picked this up from Amir @ Avus earlier this week. Waited until it was tested and true at the track (today). Beautiful piece, well constructed and functional. Some of the best money spent! In combination with true R-Comp tires and a 3.64 differential, I bettered my best time by 3.9 seconds today @ Auto Club Speedway.

Cheers

i get the feeling you don't run any kind of undertray except the splitter?
TIA

[havasusteve1]

i get the feeling you don't run any kind of undertray except the splitter?
TIA

Yeah, no fender liners and just this. Well, actually I have brake duct lines and an oil cooler, but the setup allows for the 4-nut only front fender removal.

[doktor b]

^^^awesome.
i may just build a gnarly splitter for my M instead of messing around with an under tray and then a splitter.

[SamGrant951]

3.0 Euro cluster in, mileage recoded, oil temp wired in, ASC deleted and a new vent piece above the glovebox as all the tabs on mine were broke, hopefully that cures the saggy glovebox. S54 Z3M radiator also arrived.

[M3Dynamic]

Bosch 24lb injecotrs

[mboor]

just bought a new set of staggered PSS's.

[SamGrant951]

glovebox fix success, no more sag. If anyone wants to fix it correctly just buy a new vent piece (all 4 of my plastic clips were broken on that piece). $61.70 from ECS.

[D Unit]

Thanks for posting this!!!

glovebox fix success, no more sag. If anyone wants to fix it correctly just buy a new vent piece (all 4 of my plastic clips were broken on that piece). $61.70 from ECS.

[Santai]

glovebox fix success, no more sag. If anyone wants to fix it correctly just buy a new vent piece (all 4 of my plastic clips were broken on that piece). $61.70 from ECS.

I apologise, but what parts from ECS do you mean? I don't understand.

[MikeH914]

KW Variant 1s, Rogue Engineering RTAB, and a Momo steering wheel hub with nardi adaptor.

[Edsta74]

new shift knob..