Page 11 of 11 FirstFirst ... 234567891011
Results 251 to 274 of 274

Thread: EWS sync without installing EDIABAS/INPA/DIS using a $10 vagcom cable

  1. #251
    Join Date
    Jan 2011
    Location
    Northern CA
    Posts
    1,988
    My Cars
    1998 M3/4/5
    Quote Originally Posted by cartoonz View Post
    Any chance this'll work with an E31, DWS II and motronic 1.7 DME's ?
    Probably not, looks like Motronic 1.7 uses K line for TX and L line for RX. You would likely need a pc with a real COM1 serial port and ADS interface to use with DIS or Tool32 (recommended).

    With Tool32 you would run the isn_lesen for motronic 1.7 and feed the value into isn_schreiben for EWS.
    S54 swap DME flashing - $100
    S54 swap CAN interface board (for proper A/C & check engine light) - $275
    e36 SAP sim/secondary air pump simulator:
    $75 - standard or $170 - plug & play
    e36 post-cat O2 sims: $115 shipped, plug & play

  2. #252
    Join Date
    Sep 2008
    Location
    Santa Barbara
    Posts
    3,462
    My Cars
    91 Dinan860 & 91 850 6sp
    thought so, but I had to check
    '91 Dinan 860 Stage III (new 6L engine)
    '91 Dinan 850 TT stage III (brand new engine) 21st Century Tech meets 18th Century Dinan...
    '91 850i 6sp (mint) (sold)
    '90 Dinan 750iL TT stage III (Guido - The Beast)
    '94 850 CSi The Detroit Auto Show car (restored to factory perfect) (sold)
    '96 850Ci, The George Carlin car
    ''73 3.0 csi, '08 535i, '03 X5 4.6is
    ...and a few other non BMW cars

  3. #253
    Join Date
    Sep 2016
    Location
    Montreal
    Posts
    47
    My Cars
    E36 m3
    @gpetersom

    Thanks a lot ! It worked like a charm. It gave me a check engine at first (4a63 BMW Fault Code – EWS Tampering or EWS Manipulation) but erased it and never came back.


    Sent from my iPhone using Tapatalk

  4. #254
    Join Date
    Aug 2014
    Location
    kentucky
    Posts
    671
    My Cars
    '98 Z3 M Roadster
    Cable is correct, drivers installed, now program keeps crashing.

    description: stopped working

    problem event name: CLR20r3
    problem signature 01: ewssync.ews
    problem signature 02: 1.0.0.0.
    problem signature 03: 5169ed2
    problem signature 04: mscorlib
    problem signature 05: 2.0.0.0
    problem signature 06: 53a11de1
    problem signature 07: 2591
    problem signature 08: 0
    problem signature 09: system.io.filenot foundexception
    OS version: 6.1.7601.2.1.0.256.1
    locale ID: 1033
    • Built S52 w/Dinan ISR-3 kit, NickG Stage 2+ Tune, Dinan Vortech V2 Supercharger, Dinan Air to Air Intercooler, Dinan CAI, Porsche 803 HFM, Buldogge 6" crank pulley, Griptec 2.90" blower pulley, Eurosport UD pulleys, Dinan 3.38 Diff, Dinan front/rear Swaybars, Dinan springs, Koni Yellow Sport Struts, Ground Control end links, South Bend Clutch Stage 3 Organic, AASCO Light Weight Flywheel 18.5#, Zionsville Radiator & Oil Cooler, Riot Racing BBTB, Schrick Intake Manifold, 42# Injectors, Schrick cams 264/256, Forged Wiseco pistons 9.0 comp., Forged Eagle rods, Supertech dual valve springs & valves, VAC crank & bearings, Supersprint mufflers, Euro Z3 midpipe, Raceland euro headers, Walbro 255, Bevauto ignition coils, Vortech Mondo bypass, Bailey Diverter DV30, Ireland Rear Subframe Bushings, Mason Engineering Strut Brace, Mason Engineering Clutch Petal, Apex 18" EC-7 Wheels, Full Custom Sound System, two trunk lids (with & without OE spoiler), Hardtop, Trunk full of AK's...

  5. #255
    Join Date
    Mar 2013
    Location
    Texas
    Posts
    182
    My Cars
    98' Hellrot M3
    Worked perfect on my Ti s52 swap, took a couple seconds to sync thanks!! @gpeterson
    Last edited by Grimm5698; 11-07-2018 at 02:38 PM.

  6. #256
    Join Date
    Jan 2011
    Location
    Northern CA
    Posts
    1,988
    My Cars
    1998 M3/4/5
    Quote Originally Posted by bubbafett View Post
    Cable is correct, drivers installed, now program keeps crashing.

    description: stopped working

    problem event name: CLR20r3
    problem signature 01: ewssync.ews
    problem signature 02: 1.0.0.0.
    problem signature 03: 5169ed2
    problem signature 04: mscorlib
    problem signature 05: 2.0.0.0
    problem signature 06: 53a11de1
    problem signature 07: 2591
    problem signature 08: 0
    problem signature 09: system.io.filenot foundexception
    OS version: 6.1.7601.2.1.0.256.1
    locale ID: 1033
    What version of Windows are you running? Any idea if .NET is installed?

    - - - Updated - - -

    Quote Originally Posted by Grimm5698 View Post
    Worked perfect on my Ti s52 swap, took a couple seconds to sync thanks!! @gpeterson
    Awesome, glad it worked for you.

  7. #257
    Join Date
    Nov 2018
    Location
    Laredo, Tx
    Posts
    8
    My Cars
    1998 323is (x2)
    Awesome program, hoping to use this on my 98 323is. I’m ordering the vag com cable and adapter right now, hopefully I’ll have it ready in a week or two

  8. #258
    Join Date
    Nov 2018
    Location
    Laredo, Tx
    Posts
    8
    My Cars
    1998 323is (x2)
    Worked on 98 323is 👍🏻

  9. #259
    Join Date
    Jul 2019
    Location
    Canada
    Posts
    601
    My Cars
    BMW E39 528i 1998
    It worked on my E39.
    Unfortunately my key is still not recognized and the car wont even crank

  10. #260
    Join Date
    Jan 2011
    Location
    Northern CA
    Posts
    1,988
    My Cars
    1998 M3/4/5
    Quote Originally Posted by Bmwe39528i1998 View Post
    It worked on my E39.
    Unfortunately my key is still not recognized and the car wont even crank
    You may want to check the wiring for the ring antenna, transmitter/receiver module (if present on your car), and park/neutral or clutch switch unless you have reason to believe something happened to your key. INPA would be helpful to see what your EWS and DME are thinking. The EWS has a relay that will interrupt the starter unless the key matches and it thinks the car is in park/neutral or clutch pushed in.

    There is info available at http://www.e38.org/EWS.pdf.

  11. #261
    Join Date
    Jan 2015
    Location
    AUSTRALIA
    Posts
    4
    My Cars
    1997 BMW 328iC Man.
    Hi all!
    I am 12 months into my issues that I have outlined earlier. One thing i thought to post/query is - does the difference in being manual or auto make a diff with this terrific little app?
    Reason I ask is; I have 2x 328i verts; one manual, one auto. I mixed up the ews modules at one stage and then ended up with both having conflicting signals. My DD was unable to be driven for 2 wks while I sought a solution, downloaded INPA etc and no success until I tripped over this program. It did not respond to my auto- write to ecu conf.. but it did to my manual!. I am back in the same place again with the auto..trying to start it and will not write to the ecu (both cars are Siemens MS41.0.
    I bought a Julie emulator but got bogged down in the technical side some time back...not an easy solution it appears if you are not coding proficient.
    The car originally ran A1 as it has only 60kmiles on it but I have to push it to move it and I am tiring of the issue!
    any input much appreciated on both issues..the Julie and the diff between auto/manual.
    Cheers
    wintech

  12. #262
    Join Date
    Dec 2019
    Location
    Virginia
    Posts
    1
    My Cars
    1997 bmw 328i
    Anyway to use a chromebook for progran or is there a chromebook version available

  13. #263
    Join Date
    Jan 2011
    Location
    Northern CA
    Posts
    1,988
    My Cars
    1998 M3/4/5
    Quote Originally Posted by AsunderTech174 View Post
    Anyway to use a chromebook for progran or is there a chromebook version available
    No, not currently.

  14. #264
    Join Date
    Dec 2019
    Location
    US
    Posts
    108
    My Cars
    1997 328i
    So i have finally got the program on windows 10. It only allows com port 3 regaurdless of which port vag com is in than when you hit read isn it just freezes does nothing and i cant get inpa to properly install to see if dme has vin and can be read. I do have CEL on

    Sent from my LG-AS993 using Tapatalk

  15. #265
    Join Date
    Jun 2014
    Location
    Austin, Texas
    Posts
    3
    My Cars
    97 civic sedan, 98 328is
    I have .NET framework 4.7 but the install wizard says I need 3.5. When I try to skip .NET installation the wizard just shuts down. Anyone else have this issue?

  16. #266
    Join Date
    Jun 2014
    Location
    Austin, Texas
    Posts
    3
    My Cars
    97 civic sedan, 98 328is

    Post

    Quote Originally Posted by munozisdead View Post
    I have .NET framework 4.7 but the install wizard says I need 3.5. When I try to skip .NET installation the wizard just shuts down. Anyone else have this issue?

    Scratch that. Dumb. Laptop just messing up.

  17. #267
    Join Date
    Oct 2018
    Location
    Hong Kong
    Posts
    1
    My Cars
    E39
    Thanks, the tool worked great for my e39 (3/98) which has a ms41.0 and an ews 3.2

    Of course it can be done with inpa too. But your tool is much more convenient.

    ps: the last 4 digits of the dme production number are equal to the ISN. Must be converted to hex and if >4096 (decimal) need to subtract 4096 first

  18. #268
    Join Date
    Mar 2021
    Location
    Portugal
    Posts
    1
    My Cars
    e36 318is
    @gpeterson do you think this cable will work? Thx!
    https://a.aliexpress.com/_mPquS2B

  19. #269
    Join Date
    Jul 2020
    Location
    Long Beach Ca
    Posts
    7
    My Cars
    e36 325i
    it worked for me thank man!
    I used these under hood port

    CABLE
    https://www.amazon.com/dp/B017IG81SQ...vopqNqPon2Ni_g

    adapter 20pin
    https://www.amazon.com/dp/B07D8RQWKL...U_FVRrk2NwnmpI

    and your software !!!!!!!!!!!!

  20. #270
    Join Date
    Jan 2022
    Location
    covasna
    Posts
    1
    My Cars
    1997 bmw m3 e36
    Hi

    can anyone help me find ISN from dump m5.2
    which address to convert to what?
    thank you for any help!!

  21. #271
    Join Date
    Aug 2022
    Location
    Indonesia
    Posts
    2
    My Cars
    1997 BMW E39 528i
    Quote Originally Posted by bram2011 View Post
    Thanks for the software.

    Testing has been successful in DME MS41 5WK90322 and EWS2 61.35-8 375 840

    I use WinXp Sp3 and INPA cable.

    Attachment 452958
    Quote Originally Posted by CityHunt3R View Post
    it worked for me thank man!
    I used these under hood port

    CABLE
    https://www.amazon.com/dp/B017IG81SQ...vopqNqPon2Ni_g

    adapter 20pin
    https://www.amazon.com/dp/B07D8RQWKL...U_FVRrk2NwnmpI

    and your software !!!!!!!!!!!!
    Nice. I guess it works with K+DCAN cable too.
    Great information. I may test this with my unsync e39

  22. #272
    Join Date
    Feb 2017
    Location
    UK
    Posts
    1
    My Cars
    bmw e39
    Hii guys
    trying to download this tread but no succes:http://e36-electronic.com/photos/EWSSync.exe
    Any one can help
    Thanks

  23. #273
    Join Date
    Feb 2022
    Location
    New York
    Posts
    5
    My Cars
    1995 E36 M3 Luxury
    So I have a 1995 e36 M3 with a suspected unaligned ews2 and DME. With the proper cabling and a windows laptop will this software work for my car. It is obd1 with ews2

  24. #274
    Join Date
    Mar 2014
    Location
    Mexico Distrito Federal
    Posts
    5
    My Cars
    X5 E70
    You can download? on my case the problem is from antivirus.

Page 11 of 11 FirstFirst ... 234567891011

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •