I'll be looking for parts to put an LS* into a 2000 E38. May go the e39 sub frame route.
Nisaan Sr20DET to e36 parts for sale!
Custom engine and tranny mounts
Driveshaft shop custom aluminum driveshaft
Wiring specialties custom sr20-e36 wiring harness.
Power steering hose needed
Top mount manifold for stock or gt28 turbo
Custom downpipe.
Selling an ls1 bare intake intake 160 shipped to your door!
Are these still available? PM or email racinjason89@gmail.com
GT40 intake system for your stock mustang 5.0
Looking for some LS swap parts. Let me know if you have anything.
Specifically:
Power Steering retrofit parts
Corvette Filter/regulator and retrofit lines
Throwout bearing with remote bleeder
Steering shaft
Throttle cable
I may be interested in some other parts as well.
I have a Driveshaft designed for the ls1 swap. Only reason im selling is im going to a bigger rear diff which warrants a new driveshaft all together.
The one i have was made by http://www.axle-exchange.com/ is 44.5" long and is steel. Comes with the appropriate 4-bolt flange as well.
Would like to get $400 for it shipped.
Current:
E38 2001 750iL - Current DD.
E36 1995 M3 Coupe - Ls1/t56 - FIXED...now with a Ford 8.8 IRS Rearend
E36 1998 323is Coupe - Back-up DD.
R53: 2005 MCS W/ GP and JCW bits. - Wifes Project Car
Past:
E36 1999 Dinan M3 Coupe AW/Sand Beige - In BMW Heaven.
For an Ls swap right? I'm interested in it. One of the last big pasts on my to buy list.
Ls2 e36 sedan
Still have it make an offer.
- - - Updated - - -
Still have this make offer.IMG_3296 - Copy (1024x683).jpg
Last edited by greenmonster138; 09-18-2015 at 07:04 AM.
SOLD!
Up for sale is my Tilton (Sonic) Bellhousing, clutch/pp/flywheel/TOB , and reverse mount starter setup that was mounted to my e30/LS1 build with a TKO 600 RR transmission. This was sold as a kit through Coleman Racing (part # 20949). It will work with TKO and other similar 4 bolt transmissions with the same spline count.
http://www.colemanracing.com/Driveli...ter-P3610.aspx
The kit includes the follow:
• Sonic Bellhousing for LS (maybe other?) blocks.
• Sonic/Tilton lightweight flywheel
• Sonic/Tilton 3 disk clutch/pressure plate setup
• Extra set of clutch disks
• Tilton hydraulic throwout bearing
• Tilton reverse mount starter
I installed this in my BMW e30/LS1 Racecar, and attended 1 track day to shake down all the changes I had made. The only time since it has had any use was moving the car in and out of the garage to make room to work on other projects. The clutch disks have virtually no wear! My racecar has sat, and I ended up pulling the motor or another project. I had hopes of resurrecting the racecar but as time has set in, the racecar just needs to go away – so parts are going up for sale.
I've got over $1900 invested, I'd like to get $1300 (shipped conus) out of this sale. If someone is interested and doesn't want the spare clutch disks, I'll separate those.
Last edited by iflytii; 12-24-2015 at 12:44 PM.
-------------------------------------------------------
8000 mile LS3, choice of camshaft. $5,500
PM me for details.
Car sold, have a couple LS Parts remaining
Firebird Coil packs and coil pack brackets $50
LS1 aluminum valve covers with gaskets only a couple thousand miles old $50
Mods can delete this post
Last edited by jon volk; 12-24-2015 at 01:13 PM.
95 M3, 5.3 LS, PTE 7675CEA, TH400/Gear Vendors OD
10.4@136 Pump gas at 3530lbs.
Build thread
http://www.bimmerforums.com/forum/sh...LS-Turbo-build
19-Row Oil Cooler! - SOLD!
http://www.bimmerforums.com/forum/sh...oler-10AN-size
Last edited by Inflame; 01-11-2016 at 12:45 PM.
- 96 328is 6.0L. (LS1 to LS2 build thread: http://forums.bimmerforums.com/forum...ad.php?2098938)
- 96 328is 5.7L. (LS1 build thread: http://forums.bimmerforums.com/forum....php?t=1289987)
- 95 ///M3 6.0L. (LS2 build thread: http://forums.bimmerforums.com/forum....php?t=1619249)
- 97 ///M3. (e46 Fender Flares/track car build thread: http://forums.bimmerforums.com/forum....php?t=1727098)
- 96 328is (Dual Fuel Pump to Surge Tank thread: http://www.bimmerforums.com/forum/sh...ad.php?1964025)
E36 T56 Vorshlag transmission mount with nylon spacer...make a reasonable offer.
http://www.vorshlag.com/product_info...roducts_id=161
I have a pair of RevShift poly motor mounts, which fit E36, E46, and E90-92 models. In the "track" 95A hardness. See: http://www.revshift.com/product-p/pmm-r36.htm
I found out these are too tall for my swap, and I had to get the shorter E30 mounts instead.
They were installed for a couple days, but never put in service. They have a tiny bit of discoloration on the bottom surface that touches the subframe, but are otherwise as new.
If one of you has a use for them, I'm offering them out for $60 (half MSRP) plus shipping. Please inquire by PM. Thanks for looking.
I posted my LS2 swapped 97 m3 Sedan for sale in the 3 series car section. I may be willing to sell the engine and trans and Vorshlag Swap kit and various item to complete someone's swap if interested. I won't be selling anything off the car until I sell the engine an trans, so PM me if you have any interest in the cars engine and trans and swap parts. All the info on the car is in the 4 sale Post. ls2 1.jpg ls27.jpgls28.jpg
FS: 3" steel driveshaft for T56 and 210mm diff Fits CX racing engine/trans mounts and 210mm rear diff. Probably won't work with a 188mm diff as the input is a bit shorter. No yoke just shaft and ujoints. 1310 joint in the rear and 1350 up front. $150 picked up in Milford CT Selling because I went with an aluminum shaft.
Last edited by jon volk; 03-26-2016 at 09:49 PM.
95 M3, 5.3 LS, PTE 7675CEA, TH400/Gear Vendors OD
10.4@136 Pump gas at 3530lbs.
Build thread
http://www.bimmerforums.com/forum/sh...LS-Turbo-build
I have a wiring specialties e36 ls1 swap harness for sale. Comes with their flashed ecu, the coolant setup for the stock gauge, and the adapter oil pressure sensor. Only modification to the harness is the maf wires were extended to run the intake on the passenger side. Also comes with electric fan with plug wired to work with pcm
Looking to get $950 or best offer
Also have the rest of the full swap kit pulled from my completed swap
Steel driveshaft with jtr flange and t56 yoke: $400
Jtr headers painted with ceramic header paint: $400
Vorshlag power steering kit:200
Vorshlag t56 throw out bearing and aluminum master cylinder: $400
Replica vorshlag motor and Trans mounts. Trans mount has sent from speed bump but still works: $400
Shipping to be determined
Last edited by AdamE36M; 03-26-2016 at 12:35 PM.
Bookmarks