i was hoping somebody here could help me out a bit. I have 18" breyton magics i recently got but they were spray painted flat black. Does anyone know how to remove the spray paint safely?Thanks in advance
It will probably be tricky, do you know if the wheels were sanded or not before they were sprayed? Acetone, mineral spirits or lacquer thinner would pull the paint off without immediately damaging the original paint, but it would take a really long time on those wheels
'88 s54 e30, '00 m5
I don't know of any way that is safe but I do know a quick way
buy some aircraft stripper/aluminum stripper from autozone or Kragen/O'Reilly. It's basicaly acid in an aerosol can. You spray a coat on and watch the paint bubble up and seperate from the aluminum then just scrap the loose paint off.
Do not breath or have this stuff contact any part of your skin. Even if a little speck of it lands on your arm you will feel it burning immediately. Water neutralizes it. It's also known to cause cancer(says in the back). But its pretty damn good at rippin through paint!
yep. just strip them to bare aluminum.
then repaint /powdercoat/polish as you want.
thanks i think i will try the aircraft and see how that works
or just paint over the black
No current BMWs.
1994 Roadmaster Wagon
1974 Alfa Romeo Berlina
Better to remove the paint with the suggest paint stripper, you never know if the PO did a good job on the paintjob before you and if he didn't the new paint going onto it is gonna be as bad as that, if it's starting to fall off at some time or cracking up. I know.. i've seen it!
Aircraft stripper is the $hit! I use it often. Only other ideal way would be to have them bead blasted.
If it's a difficult wheel then media blasting or professional stripping is your best bet.
By the time you are done with stripper and F'ing around until your fingers bleed you'll still be out $25 or better in materials.
It cost me $20 a pop(blasting) last time.
If you can leave two black stripes from the exit of one corner to the braking zone of the next, you have enough horsepower. - Mark Donohue
or sand blast them ........lol
93BMW 525i -16"momo, KN filter ,Daily driver
Wire Wheel acid. Spray on let sit and rinse off no elbow grease required
1996 332IS
Built 3.2
CES/Steed TS Precision 6466, spraying a "$π!℅" load of meth.
Technique Tuning 80# tune.
1/4 mile 10.84 @ 136.72
Your 1 and only stop for all your BMW performance needs
WWW.CESMOTORSPORT.COM
I haven't tried the aircraft brand, but I've use Jasco aresol stripper, which is the best I've tried. It will take spray paint off in a heartbeat, but is almost completely innefective against factory wheel paint (style 5 specifically). It will take the clear off the rims with enough applications, but not the center paint. I finally had the sandblasted, which left a rough finish because it takes a very aggressive sand to remove that tough paint. Next time I would just paint over it. You can't get it off, it's definitely not going to fall off.
Brake fluid will work too ...lol
1996 332IS
Built 3.2
CES/Steed TS Precision 6466, spraying a "$π!℅" load of meth.
Technique Tuning 80# tune.
1/4 mile 10.84 @ 136.72
Your 1 and only stop for all your BMW performance needs
WWW.CESMOTORSPORT.COM
I had spray painted my rims as a theft deterrent after my original rims were stolen last December. Stupid move! At them time, I had no intention of selling my car, a 2008 Honda Accord. Now I am trying to sell it. I learned today that simple adhesive remover will remove the paint. Other possibilities are paint thinner and graffiti remover. Try those first before resorting to the stronger stuff. The paint may not be as difficult to remove as you think.
Great bump. A+ thread, would read again
I own mostly junk. Except the Porsche, that's kind of cool.
All the motorcycles are trash which you can read about at
http://oneguytwowheels.blogspot.com/
I'll update it eventually
Thansk
We have a stripper that charges $25 a wheel to soda wash the wheels. Not abrasive like sand blasting. The wheel comes out ready for polish and paint without the pits that sand blasting can cause. Media blasting with something like walnut shells is much better than sand if you want to go with blasting them.
Cheers,
Jim
1990 M3
1995 E34 540/6
1992 525it
Bookmarks