I need help
My computer is win10 64 VMWARE15
Stay in the systen is coming up please wait.............
留在系統即將到來請等待.............Attachment 638103
Are there any new guides with links? This is all down.
heres the link for your GTA1 files. Make sure and follow the OP's directions on page 1.
https://mega.nz/#F!qK4V0KZD!CA2ljfjmO1L6xoKRbU-mRw
awesome! appreciate the info
thank you eriknight! finally got it working on my computer.
for fresh installs of GT1/DIS, you need to install INPA. make sure that works and talking with the car before moving on to install GT1.
Hey guys, i installed DIS running on a virtual machine. My diagnostic head however does not get recognized from DIS or SSS. Its likely my EDIABAS file or virtual machine isn't set up right. My Car been sitting for 5 months on a DME swap. help please
m sure its a small fix via teamveiwer
hopefully im not out of place here. is that what I would use to reset my throttle on a 99 bmw. from my understanding I need to reset it if I replace it. Is it difficult to use these programs and where do I purchase? thanks.
Can someone provide a working download link for easydis v44 and VMware 6 / 6.5, maybe even inpa 3.x?
Thanks.
Last edited by Michalp; 05-16-2019 at 01:25 PM.
Anyone have any issues connecting on a windows 7 32bit machine using a true serial port cable to an OBD2 car? I copied my setup from my windows xp machine that worked fine and even went back over DavidMc read this first pdf and I am still unable to get ifhsrv to apply the IP and connect to the car. I have ediabas configured correctly for IP and port as well. INPA works perfectly...
Last edited by purplecty; 07-28-2019 at 03:13 PM.
Nevermind I win... Windows7 ultimate required me to manually apply the IP to the windows side of the tcp/ip v4 connection for the VMnet adapter in the network and sharing center. After this the API Test passed and I was able to communicate with the car using gerts serial cable successfully. It appears windows xp automatically assigned the IP or it's been so long that I missed this step...
hi. iv tiny ads interface and dis v44. DME reads ok, but cant read EGS.
how to fix this ? :|
edit: e36 318 m43 1994, 4l30e automatic gearbox
68253290_2969946179713184_5581459006452400128_n.jpg
68816547_2969946173046518_6802336905250734080_n.jpg
Last edited by 318ia; 08-09-2019 at 12:43 PM.
anyone ?
hi
no, just DME.
this car has no ABS or airbag
Last edited by 318ia; 08-18-2019 at 10:14 AM.
Is your ediabas.ini set to ADS and did you run ADSSetup.exe which is only required once?
exactly
Hello everyone.i have similar problem with same interface as 318ia.i can read all other modules exept egs module.i am using dell d630 wich has some wierd com port or something.replaced ads32.dll file with specially for dell computers modified ads32.dll file.changed so much that now i can read zf 5hp18 egs but not older gearboxes such as e32 4hp22 or e36 325td wich has gm automatic.dis v44 says something like no module found
Make sure it is installed...etc(exactly same error as pictured by 318ia).any ideas please.
Last edited by Nugis316; 09-03-2019 at 06:49 AM.
Quick question. I’m on the last step (installation under administration). If this works, am I going to have to go through this set up every single time I want to use the program?
Reason I ask is because the few times it froze I had to start over and each time I started over I could get a little farther. Will this be locked in once I get through the last step?
EDIT
after pages of reading i got it working, corrected all my issues and passed my vanos test. Thanks.
Last edited by PITT M3 RR; 10-31-2019 at 11:24 AM.
I can't seem to find the files for download, seems all the links are dead. Does anyone know where to get them?
Pm me your email I’ll send you what I have saved. Somehow I got it working and it’s 99% English
i had dis v44 but my hard drive broke and all got lost. cant find working dis or vmware 6.5 anywhere. Ista D would be nice too beacause that works on obd one bmws too? so can someone put links where to dl?
I may have found a link where to download DIS v44. https://www.beemerlab.org/2015/07/wo...on-simple.html
Hi
Like many I'm having some problems with my install, I've read several sets of instructions and searched a lot but to no avail yet.
Any help would be much appreciated.
I managed to get Easy Dis up and running and also to install VMware.
error is when the black "system is starting" page is displayed:
portmapper on server 192.168.68.30 is not responding
Easy DIS tries to start, displays this error and then goes to a blank screen but with the mouse cursor showing (previously it had loaded up)
I've been going into the scoadmin page of Unix and trying different network adapter configurations to no avail.
I tried to look at one of my Intel network adapters on windows device manager (windows XP) and the added a new network card with matching bus and device.
This is on a Dell Latitude D505 laptop...
Driving me nuts!!!!!!!!!
Any pointers??
Bookmarks