FS: TT(Nick G) stage 3 Turbo Tune

[vollosso]

I would really like to get this sold to free up some cash for parts so im going to include the maf and harness.

You will need to purchase injectors! LINK (http://www.amazon.com/SIEMENS-Injector-107961-Chrysler-Mitsubishi/dp/B008RA6XWY)

575$ shipped for ecu/maf/harness

or 560$ paypal gift.

Would trade for certain turbos/certain intercoolers.
________________________________________

Link to original thread: LINK (http://www.bimmerforums.com/forum/showthread.php?1999686-FS-TT-stage-3-Turbo-Tuning-Package)

Up for sale is a TT/Nick G software.

This is by far the most reliable turbo tune you can have on your car. This set up was used on an S52 with a GT3582R and made 553 whp / 578 wtrq at 20 psi.

Stage 3 from NickG is for a GT35R, 60# injectors, 8.5:1 compression, 20 psi boost.

The tune also deletes secondary O2 sensors, and SAP system.

This tune should work for most any setup running low compression and a 35r.

PLEASE PM ME OR EMAIL ME FOR FURTHER DETAILS.

Asking 500$ OBO, Vollosso@gmail.com / PM me.

Q/A:

1. you can use any fuel pump with these injectors as long as its not running over your fpr. AKA a walbro 255 with OEM FPR will be Great!
2. considering its a MAF system it should work for varying turbos, anything that will spool in the same ranges: 6262, 6266, 6466, s360, gtx35r etc etc.
3. The ecu is ews locked. I can include software to synch this to your car in 3 minutes or you can go to any GT1 software owner or and dealer etc etc.
4. this turbo tune should work for any compatible setups including frankenstein engines and 9:1 engines.

[Keith1054]

PM sent

[chikinhed]

This was my old tune if you have an questions. It ran great.

Sent from my GTX3582R

[m3mods]

Are you including the maf and injectors or just the dme?

[vollosso]

Just the dme i could also sell the maf.

[vollosso]

Bump.

[Butters Stoch]

Just the dme i could also sell the maf.

This needs harness as well.

[vollosso]

This needs harness as well. the 6-pin harness will be included with the maf.

[gnarfy]

is it the same MAF as stage 2 ? was it used with a Walbro 255lph fuel pump, or it need to be upgraded ?

[vollosso]

is it the same MAF as stage 2 ? was it used with a Walbro 255lph fuel pump, or it need to be upgraded ?

Yes i believe it is the same as stage 2 maf.

And yes i think it was a walbro 255 but it may have been a aeromotive 340. Chikinhed may chime in or i will Ask him. Regardless as long as your fpr is handling the pump properly it will work with this tune.

[chikinhed]

^ What he said.

I was using a Walbro 255 and then upgraded the lines to -6 and pump to a Walbro 400.

Sent from my GTX3582R

[gnarfy]

interested, what about 500$ shipped to canada ?

[gnarfy]

anyone tried the stage 3 tune with 60# on stock motor with lower compression gasket (TT S2)? it run perfect as now, but I'm not too sure if the engine would hold over 15psi with GTX or GTW and 60#...

really interested, I might buy and upgrade later when my 60-1 will need to be replaced...

[Butters Stoch]

anyone tried the stage 3 tune with 60# on stock motor with lower compression gasket (TT S2)? it run perfect as now, but I'm not too sure if the engine would hold over 15psi with GTX or GTW and 60#...

really interested, I might buy and upgrade later when my 60-1 will need to be replaced...

Buy this.
Its blowing my mind that its still available.

[gnarfy]

good idea Butters, you just convinced me.. volosso, send me your paypal email, I'll transfer you the money as soon as I get it...

[Butters Stoch]

good idea Butters, you just convinced me.. volosso, send me your paypal email, I'll transfer you the money as soon as I get it...

Great, then call me and we will get you a new turbi

[gnarfy]

Great, then call me and we will get you a new turbi

Yep, I'll try to save for a GTX3582r, if I can't afford I'll take a gtw.. but I'll let you know for sure !